Hi Lee, I have checked in Snowball schematics and I can confirm that the fixed 3.3V regulator is GPIO26 on AB8500 not DB8500, so its numero is MOP500_AB8500_PIN_GPIO(26) and you have first to update the upstream gpio-ab8500 driver.
BR, Philippe On 08/24/2012 02:48 PM, Lee Jones wrote: > The SMSC911x Ethernet chip requires a fixed-regulator in order to > function correctly. We have previously provided a means to obtain > this during a Device Tree boot, however nothing has been put into > place when booting with a non-DT kernel. This patch aims to change > that. > > Signed-off-by: Lee Jones <lee.jo...@linaro.org> > --- > arch/arm/mach-ux500/board-mop500-regulators.c | 17 +++++++++++++++++ > arch/arm/mach-ux500/board-mop500-regulators.h | 1 + > arch/arm/mach-ux500/board-mop500.c | 21 +++++++++++++++++++++ > arch/arm/mach-ux500/board-mop500.h | 2 +- > 4 files changed, 40 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c > b/arch/arm/mach-ux500/board-mop500-regulators.c > index 52426a4..139f31e 100644 > --- a/arch/arm/mach-ux500/board-mop500-regulators.c > +++ b/arch/arm/mach-ux500/board-mop500-regulators.c > @@ -13,6 +13,23 @@ > #include <linux/regulator/ab8500.h> > #include "board-mop500-regulators.h" > > +#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE > +static struct regulator_consumer_supply gpio_en_3v3_consumers[] = { > + REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), > +}; > + > +struct regulator_init_data gpio_en_3v3_regulator = { > + .constraints = { > + .name = "EN-3V3", > + .min_uV = 3300000, > + .max_uV = 3300000, > + .valid_ops_mask = REGULATOR_CHANGE_STATUS, > + }, > + .num_consumer_supplies = ARRAY_SIZE(gpio_en_3v3_consumers), > + .consumer_supplies = gpio_en_3v3_consumers, > +}; > +#endif > + > /* > * TPS61052 regulator > */ > diff --git a/arch/arm/mach-ux500/board-mop500-regulators.h > b/arch/arm/mach-ux500/board-mop500-regulators.h > index 9499215..78a0642 100644 > --- a/arch/arm/mach-ux500/board-mop500-regulators.h > +++ b/arch/arm/mach-ux500/board-mop500-regulators.h > @@ -18,5 +18,6 @@ extern struct ab8500_regulator_reg_init > ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS]; > extern struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS]; > extern struct regulator_init_data tps61052_regulator; > +extern struct regulator_init_data gpio_en_3v3_regulator; > > #endif > diff --git a/arch/arm/mach-ux500/board-mop500.c > b/arch/arm/mach-ux500/board-mop500.c > index 42e1759..c7f0973 100644 > --- a/arch/arm/mach-ux500/board-mop500.c > +++ b/arch/arm/mach-ux500/board-mop500.c > @@ -23,6 +23,7 @@ > #include <linux/spi/spi.h> > #include <linux/mfd/abx500/ab8500.h> > #include <linux/regulator/ab8500.h> > +#include <linux/regulator/fixed.h> > #include <linux/mfd/tc3589x.h> > #include <linux/mfd/tps6105x.h> > #include <linux/mfd/abx500/ab8500-gpio.h> > @@ -75,6 +76,25 @@ static struct platform_device snowball_led_dev = { > }, > }; > > +#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE > +static struct fixed_voltage_config snowball_gpio_en_3v3_data = { > + .supply_name = "EN-3V3", > + .gpio = SNOWBALL_EN_3V3_ETH_GPIO, > + .microvolts = 3300000, > + .enable_high = 1, > + .init_data = &gpio_en_3v3_regulator, > + .startup_delay = 5000, /* 1200us */ > +}; > + > +static struct platform_device snowball_gpio_en_3v3_regulator_dev = { > + .name = "reg-fixed-voltage", > + .id = 1, > + .dev = { > + .platform_data = &snowball_gpio_en_3v3_data, > + }, > +}; > +#endif > + > static struct ab8500_gpio_platform_data ab8500_gpio_pdata = { > .gpio_base = MOP500_AB8500_PIN_GPIO(1), > .irq_base = MOP500_AB8500_VIR_GPIO_IRQ_BASE, > @@ -585,6 +605,7 @@ static struct platform_device *snowball_platform_devs[] > __initdata = { > &snowball_led_dev, > &snowball_key_dev, > &snowball_sbnet_dev, > + &snowball_gpio_en_3v3_regulator_dev, > }; > > static void __init mop500_init_machine(void) > diff --git a/arch/arm/mach-ux500/board-mop500.h > b/arch/arm/mach-ux500/board-mop500.h > index 9e9dd5a..d3a02d5 100644 > --- a/arch/arm/mach-ux500/board-mop500.h > +++ b/arch/arm/mach-ux500/board-mop500.h > @@ -13,6 +13,7 @@ > #include <linux/amba/mmci.h> > > /* Snowball specific GPIO assignments, this board has no GPIO expander */ > +#define SNOWBALL_EN_3V3_ETH_GPIO 26 No it's MOP500_AB8500_PIN_GPIO(26) > #define SNOWBALL_ACCEL_INT1_GPIO 163 > #define SNOWBALL_ACCEL_INT2_GPIO 164 > #define SNOWBALL_MAGNET_DRDY_GPIO 165 > @@ -76,7 +77,6 @@ > #define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) > /* SYSCLKREQ6/GPIO4 */ > #define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) > /* PWMOUT3/GPIO16 */ > #define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) > /* SYSCLKREQ7/GPIO24 */ > -#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* > GPIO26 */ keep this line > > struct device; > struct i2c_board_info; -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/