On Thu, Oct 25, 2012 at 12:00:08PM +0530, [email protected] wrote: > From: Vineet Gupta <[email protected]> > > Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys) > FPGA Boards such as ARCAngel4/ML50x > > Signed-off-by: Vineet Gupta <[email protected]> > --- > drivers/tty/serial/Kconfig | 25 ++ > drivers/tty/serial/Makefile | 1 + > drivers/tty/serial/arc_uart.c | 747 > ++++++++++++++++++++++++++++++++++++++ > include/uapi/linux/serial_core.h | 2 + > 4 files changed, 775 insertions(+), 0 deletions(-) > create mode 100644 drivers/tty/serial/arc_uart.c > > diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig > index 2a53be5..efee7fe 100644 > --- a/drivers/tty/serial/Kconfig > +++ b/drivers/tty/serial/Kconfig > @@ -1423,4 +1423,29 @@ config SERIAL_EFM32_UART_CONSOLE > depends on SERIAL_EFM32_UART=y > select SERIAL_CORE_CONSOLE > > +config SERIAL_ARC > + bool "ARC UART driver support" > + select SERIAL_CORE > + default y > + help > + Driver for on-chip UART for ARC(Synopsys) for the legacy > + FPGA Boards (ML50x/ARCAngel4)
Unless you will break a user's box, NEVER define a default value for a new configuration option as y. And why can't I select this driver as a module? > + > +config SERIAL_ARC_CONSOLE > + bool > + select SERIAL_CORE_CONSOLE > + depends on SERIAL_ARC=y > + default y > + help > + Enable system Console on ARC UART > + > +config SERIAL_ARC_NR_PORTS > + int 'Number of ports' > + range 1 3 > + default 1 > + depends on SERIAL_ARC > + help > + Set this to the number of serial ports you want the driver > + to support. > + > endmenu > diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile > index 4f694da..df1b998 100644 > --- a/drivers/tty/serial/Makefile > +++ b/drivers/tty/serial/Makefile > @@ -82,3 +82,4 @@ obj-$(CONFIG_SERIAL_XILINX_PS_UART) += xilinx_uartps.o > obj-$(CONFIG_SERIAL_SIRFSOC) += sirfsoc_uart.o > obj-$(CONFIG_SERIAL_AR933X) += ar933x_uart.o > obj-$(CONFIG_SERIAL_EFM32_UART) += efm32-uart.o > +obj-$(CONFIG_SERIAL_ARC) += arc_uart.o > diff --git a/drivers/tty/serial/arc_uart.c b/drivers/tty/serial/arc_uart.c > new file mode 100644 > index 0000000..9215bf4 > --- /dev/null > +++ b/drivers/tty/serial/arc_uart.c > @@ -0,0 +1,747 @@ > +/* > + * ARC On-Chip(fpga) UART Driver > + * > + * Copyright (C) 2010-2012 Synopsys, Inc. (www.synopsys.com) > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * vineetg: July 10th 2012 > + * -Decoupled the driver from arch/arc > + * +Using platform_get_resource() for irq/membase (thx to bfin_uart.c) > + * +Using early_platform_xxx() for early console (thx to > mach-shmobile/xxx) > + * > + * Vineetg: Aug 21st 2010 > + * -Is uart_tx_stopped() not done in tty write path as it has already been > + * taken care of, in serial core > + * > + * Vineetg: Aug 18th 2010 > + * -New Serial Core based ARC UART driver > + * -Derived largely from blackfin driver albiet with some major tweaks > + * > + * TODO: > + * -check if sysreq works > + */ > + > +#if defined(CONFIG_SERIAL_ARC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) > +#define SUPPORT_SYSRQ > +#endif Are you sure this works? Don't you usually need to include some .h files before you check these config values? > + > +#include <linux/module.h> > +#include <linux/serial.h> > +#include <linux/console.h> > +#include <linux/sysrq.h> > +#include <linux/platform_device.h> > +#include <linux/tty.h> > +#include <linux/tty_flip.h> > +#include <linux/serial_core.h> > +#include <linux/io.h> > + > +/************************************* > + * ARC UART Hardware Specs > + ************************************/ > +#define ARC_UART_TX_FIFO_SIZE 1 > + > +/* > + * UART Register set (this is not a Standards Compliant IP) > + * Also each reg is Word aligned, but only 8 bits wide > + */ > +#define R_ID0 0 > +#define R_ID1 1 > +#define R_ID2 2 > +#define R_ID3 3 > +#define R_DATA 4 > +#define R_STS 5 > +#define R_BAUDL 6 > +#define R_BAUDH 7 > + > +/* Bits for UART Status Reg (R/W) */ > +#define RXIENB 0x04 /* Receive Interrupt Enable */ > +#define TXIENB 0x40 /* Transmit Interrupt Enable */ > + > +#define RXEMPTY 0x20 /* Receive FIFO Empty: No char receivede */ > +#define TXEMPTY 0x80 /* Transmit FIFO Empty, thus char can be written into */ > + > +#define RXFULL 0x08 /* Receive FIFO full */ > +#define RXFULL1 0x10 /* Receive FIFO has space for 1 char (tot space=4) */ > + > +#define RXFERR 0x01 /* Frame Error: Stop Bit not detected */ > +#define RXOERR 0x02 /* OverFlow Err: Char recv but RXFULL still set */ > + > +/* Uart bit fiddling helpers: lowest level */ > +#define RBASE(uart, reg) ((unsigned int *)uart->port.membase + reg) > +#define UART_REG_SET(u, r, v) writeb((v), RBASE(u, r)) > +#define UART_REG_GET(u, r) readb(RBASE(u, r)) What happens when you run sparse on this driver? thanks, greg k-h -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
