On 11/22/2012 06:42 PM, Minchan Kim wrote:
Now zram document syas "set disksize is optional"
but partly it's wrong. When you try to use zram firstly after
booting, you must set disksize, otherwise zram can't work because
zram gendisk's size is 0. But once you do it, you can use zram freely
after reset because reset doesn't reset to zero paradoxically.
So in this time, disksize setting is optional.:(
It's inconsitent for user behavior and not straightforward.
This patch forces always setting disksize firstly before using zram.
Yes. It changes current behavior so someone could complain when
he upgrades zram. Apparently it could be a problem if zram is mainline
but it still lives in staging so behavior could be changed for right
way to go. Let them excuse.
Signed-off-by: Minchan Kim <minc...@kernel.org>
---
drivers/staging/zram/zram.txt | 7 +++--
drivers/staging/zram/zram_drv.c | 57 ++++++++++++++-----------------------
drivers/staging/zram/zram_drv.h | 5 +---
drivers/staging/zram/zram_sysfs.c | 6 +---
4 files changed, 27 insertions(+), 48 deletions(-)
diff --git a/drivers/staging/zram/zram.txt b/drivers/staging/zram/zram.txt
index 5f75d29..00ae66b 100644
--- a/drivers/staging/zram/zram.txt
+++ b/drivers/staging/zram/zram.txt
@@ -23,10 +23,9 @@ Following shows a typical sequence of steps for using zram.
This creates 4 devices: /dev/zram{0,1,2,3}
(num_devices parameter is optional. Default: 1)
-2) Set Disksize (Optional):
+2) Set Disksize
Set disk size by writing the value to sysfs node 'disksize'
- (in bytes). If disksize is not given, default value of 25%
- of RAM is used.
+ (in bytes).
Disksize can now be set using K/M/G suffixes also (see Sergey's change:
handle mem suffixes in disk size ...). So, this should be documented as:
2) Set Disksize
Set disk size by writing the value to sysfs node 'disksize'.
The value can be either in bytes or you can use mem suffixes.
Examples:
# Initialize /dev/zram0 with 50MB disksize
echo $((50*1024*1024)) > /sys/block/zram0/disksize
# Using mem suffixes
echo 256K > /sys/block/zram0/disksize
echo 512M > /sys/block/zram0/disksize
echo 1G > /sys/block/zram0/disksize
# Initialize /dev/zram0 with 50MB disksize
echo $((50*1024*1024)) > /sys/block/zram0/disksize
@@ -67,6 +66,8 @@ Following shows a typical sequence of steps for using zram.
(This frees all the memory allocated for the given device).
+ If you want to use zram again, you should set disksize first
+ due to reset zram.
This frees all the memory allocated for the given device and resets the
disksize to zero. You must set the disksize again before reusing the device.
Please report any problems at:
- Mailing list: linux-mm-cc at laptop dot org
diff --git a/drivers/staging/zram/zram_drv.c b/drivers/staging/zram/zram_drv.c
index fb4a7c9..9ef1eca 100644
--- a/drivers/staging/zram/zram_drv.c
+++ b/drivers/staging/zram/zram_drv.c
@@ -104,35 +104,6 @@ static int page_zero_filled(void *ptr)
return 1;
}
-static void zram_set_disksize(struct zram *zram, size_t totalram_bytes)
-{
- if (!zram->disksize) {
- pr_info(
- "disk size not provided. You can use disksize_kb module "
- "param to specify size.\nUsing default: (%u%% of RAM).\n",
- default_disksize_perc_ram
- );
- zram->disksize = default_disksize_perc_ram *
- (totalram_bytes / 100);
- }
-
- if (zram->disksize > 2 * (totalram_bytes)) {
- pr_info(
- "There is little point creating a zram of greater than "
- "twice the size of memory since we expect a 2:1 compression "
- "ratio. Note that zram uses about 0.1%% of the size of "
- "the disk when not in use so a huge zram is "
- "wasteful.\n"
- "\tMemory Size: %zu kB\n"
- "\tSize you selected: %llu kB\n"
- "Continuing anyway ...\n",
- totalram_bytes >> 10, zram->disksize
- );
- }
-
- zram->disksize &= PAGE_MASK;
-}
-
static void zram_free_page(struct zram *zram, size_t index)
{
unsigned long handle = zram->table[index].handle;
@@ -497,6 +468,9 @@ void __zram_reset_device(struct zram *zram)
{
size_t index;
+ if (!zram->init_done)
+ goto out;
+
zram->init_done = 0;
/* Free various per-device buffers */
@@ -523,8 +497,9 @@ void __zram_reset_device(struct zram *zram)
/* Reset stats */
memset(&zram->stats, 0, sizeof(zram->stats));
-
+out:
zram->disksize = 0;
+ set_capacity(zram->disk, 0);
}
void zram_reset_device(struct zram *zram)
@@ -540,13 +515,26 @@ int zram_init_device(struct zram *zram)
size_t num_pages;
down_write(&zram->init_lock);
-
if (zram->init_done) {
up_write(&zram->init_lock);
return 0;
}
- zram_set_disksize(zram, totalram_pages << PAGE_SHIFT);
+ BUG_ON(!zram->disksize);
It shouldn't cause a crash if user sets disksize to zero; a noop seems
better.
Thanks,
Nitin
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/