-----Original Message----- From: Robert Hancock [mailto:hancock...@gmail.com] Sent: Wednesday, November 28, 2012 7:35 PM To: Justin Piszcz Cc: 'Bjorn Helgaas'; 'Bruno Prémont'; supp...@supermicro.com; linux-kernel@vger.kernel.org; 'Dan Williams' Subject: Re: Supermicro X9SRL-F - channel enumeration error & ACPI/firmware bug question
What does lspci -vv show on that controller? Not sure what actual chipset that controller is, but there's a known issue with some Marvell 6Gbps SATA controllers with DMAR enabled - it seems the device issues memory read/write requests from the wrong PCI function ID and the IOMMU rightly denies access as the function listed in the requests doesn't have any mapping to that memory. I don't think there's presently a workaround other than disabling DMAR. We could (and likely should) be detecting that device and adding some kind of quirk for it. That sounds likely... It is shown below: Card name: HighPoint Rocket 620 Dual Port SATA 6 Gbps PCI Express 2.0 Host Adapter lspci -vv output: 84:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9123 PCIe SATA 6.0 Gb/s controller (rev 11) (prog-if 01 [AHCI 1.0]) Subsystem: Marvell Technology Group Ltd. 88SE9123 PCIe SATA 6.0 Gb/s controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 119 Region 0: I/O ports at e000 [size=8] Region 1: I/O ports at dc00 [size=4] Region 2: I/O ports at ec00 [size=8] Region 3: I/O ports at e800 [size=4] Region 4: I/O ports at e400 [size=16] Region 5: Memory at cfeee000 (32-bit, non-prefetchable) [size=2K] Expansion ROM at cfef0000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee20000 Data: 4076 Capabilities: [70] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 256 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: ahci > > -- > > > ==> Further issues with the X9SRL-F -- does this board support ASPM or is > this a Linux/ASPM implementation issue? > [ 0.632170] pci0000:ff: ACPI _OSC support notification failed, disabling > PCIe ASPM > [ 0.632239] pci0000:ff: Unable to request _OSC control (_OSC support > mask: 0x08) What's the full dmesg from this machine (or is it already posted somewhere)? It is now available here: http://home.comcast.net/~jpiszcz/20121128/dmesg.txt Justin. -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/