On Thu, 2012-11-29 at 11:03 +0100, Rafael J. Wysocki wrote: > On Wednesday, November 28, 2012 06:15:42 PM Toshi Kani wrote: > > On Wed, 2012-11-28 at 18:02 -0700, Toshi Kani wrote: > > > On Thu, 2012-11-29 at 00:49 +0100, Rafael J. Wysocki wrote: > > > > On Wednesday, November 28, 2012 02:02:48 PM Toshi Kani wrote: > > > > If we disabled exposing > > > > acpi_eject_store() for memory devices, then the only way would be from > > > > the > > > > notify handler. So I wonder if driver_unbind() shouldn't just > > > > uninstall the > > > > notify handler for memory (so that memory eject events are simply > > > > dropped on > > > > the floor after unbinding the driver)? > > > > > > If driver_unbind() happens before an eject request, we do not have a > > > problem. acpi_eject_store() fails if a driver is not bound to the > > > device. acpi_memory_device_notify() fails as well. > > > > > > The race condition Wen pointed out (see the top of this email) is that > > > driver_unbind() may come in while eject operation is in-progress. This > > > is why I mentioned the following in previous email. > > > > > > > So, we basically need to either 1) serialize > > > > acpi_bus_hot_remove_device() and driver_unbind(), or 2) make > > > > acpi_bus_hot_remove_device() to fail if driver_unbind() is run > > > > during the operation. > > > > Forgot to mention. The 3rd option is what Greg said -- use the > > suppress_bind_attrs field. I think this is a good option to address > > this race condition for now. For a long term solution, we should have a > > better infrastructure in place to address such issue in general. > > Well, in the meantime I've had a look at acpi_bus_hot_remove_device() and > friends and I think there's a way to address all of these problems > without big redesign (for now). > > First, why don't we introduce an ACPI device flag (in the flags field of > struct acpi_device) called eject_forbidden or something like this such that: > > (1) It will be clear by default. > (2) It may only be set by a driver's .add() routine if necessary. > (3) Once set, it may only be cleared by the driver's .remove() routine if > it's safe to physically remove the device after the .remove(). > > Then, after the .remove() (which must be successful) has returned, and the > flag is set, it will tell acpi_bus_remove() to return a specific error code > (such as -EBUSY or -EAGAIN). It doesn't matter if .remove() was called > earlier, because if it left the flag set, there's no way to clear it afterward > and acpi_bus_remove() will see it set anyway. I think the struct acpi_device > should be unregistered anyway if that error code is to be returned.
I like the idea! It's a good intermediate solution if we need to keep the bind/unbind interface. That said, I still prefer to go with option 3) for now. I do not see much reason to keep the bind/unbind interface for ACPI hotplug drivers, and it seems that the semantics of .remove() is .remove_driver(), not .remove_device() for driver_unbind(). So, I think we should disable the bind/unbind interface until we settle this issue. > [By the way, do you know where we free the memory allocated for struct > acpi_device objects?] device_release() -> acpi_device_release(). > Now if acpi_bus_trim() gets that error code from acpi_bus_remove(), it should > store it, but continue the trimming normally and finally it should return that > error code to acpi_bus_hot_remove_device(). > > Now, if acpi_bus_hot_remove_device() gets that error code, it should just > reverse the whole trimming (i.e. trigger acpi_bus_scan() from the device > we attempted to eject) and notify the firmware about the failure. > > If we have that, then the memory hotplug driver would only need to set > flags.eject_forbidden in its .add() routine and make its .remove() routine > only clear that flag if it is safe to actually remove the memory. > > Does this make sense to you? In high-level, yes. Rollback strategy, such as we should continue the trimming after an error, is something we need to think about along with the framework design. I think we need a good framework before implementing rollback. > [BTW, using _PS3 in acpi_bus_hot_remove_device() directly to power off the > device is a nonsense, because this method is not guaranteed to turn the power > off in the first place (it may just put the device into D3hot). If anything, > acpi_device_set_power() should be used for that, but even that is not > guaranteed to actually remove the power (power resources may be shared with > other devices, so in fact that operation should be done by acpi_bus_trim() > for each of the trimmed devices.] I agree. I cannot tell for other vendor's implementation, but I expect that _EJ0 takes care of the power state after it is ejected. Thanks, -Toshi -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
