Hi Jason and Sebastian, Sebastian Hesselbarth <[email protected]> writes:
> With DT support for mv643xx_eth board specific init for some boards now > is unneccessary. Remove those board files, Kconfig entries, and > corresponding entries in kirkwood_defconfig. > > Signed-off-by: Sebastian Hesselbarth <[email protected]> > --- > Note: board-km_kirkwood.c is also removed, as Valentin Longchamp confirmed > the lock-up is not caused by accessing clock gating registers but rather > non-existent device registers. This will be addressed by dtsi separation > for kirkwood and bobcat SoC variants. > > Changelog: > v3->v4: > - remove more boards that don't require board specific setup > > Cc: David Miller <[email protected]> > Cc: Lennert Buytenhek <[email protected]> > Cc: Jason Cooper <[email protected]> > Cc: Andrew Lunn <[email protected]> > Cc: Benjamin Herrenschmidt <[email protected]> > Cc: [email protected] > Cc: [email protected] > Cc: [email protected] > Cc: [email protected] > --- > arch/arm/configs/kirkwood_defconfig | 16 ---- > arch/arm/mach-kirkwood/Kconfig | 117 > ------------------------- > arch/arm/mach-kirkwood/Makefile | 16 ---- > arch/arm/mach-kirkwood/board-dnskw.c | 7 -- > arch/arm/mach-kirkwood/board-dockstar.c | 32 ------- > arch/arm/mach-kirkwood/board-dreamplug.c | 35 -------- > arch/arm/mach-kirkwood/board-dt.c | 62 +------------ > arch/arm/mach-kirkwood/board-goflexnet.c | 34 ------- > arch/arm/mach-kirkwood/board-guruplug.c | 33 ------- > arch/arm/mach-kirkwood/board-ib62x0.c | 29 ------ > arch/arm/mach-kirkwood/board-iconnect.c | 10 --- > arch/arm/mach-kirkwood/board-iomega_ix2_200.c | 34 ------- > arch/arm/mach-kirkwood/board-km_kirkwood.c | 44 ---------- > arch/arm/mach-kirkwood/board-lsxl.c | 16 ---- > arch/arm/mach-kirkwood/board-mplcec4.c | 14 --- > arch/arm/mach-kirkwood/board-ns2.c | 35 -------- > arch/arm/mach-kirkwood/board-openblocks_a6.c | 26 ------ > arch/arm/mach-kirkwood/board-readynas.c | 6 -- Just a stupid note: With Thomas ongoing work to get mvebu-pcie driver in place and enabled for kirkwood, some boards setup files will also lose their pcie init routines, which may allow you to kill those additonal files soon. For instance 6bd98481ab34 (arm: kirkwood: NETGEAR ReadyNAS Duo v2 init PCIe via DT) currently sitting in jcooper/mvebu/pcie_kirkwood removes the PCIE init routine in board-readynas.c, and yours remove ge00 init. With both applied, the whole file can go away. AFAICT, this may be the case soon for: arch/arm/mach-kirkwood/board-iconnect.c (36e5722089) arch/arm/mach-kirkwood/board-mplcec4.c (9470fbfb8d) arch/arm/mach-kirkwood/board-nsa310.c (40fa8e5da2) arch/arm/mach-kirkwood/board-readynas.c (6bd98481ab) arch/arm/mach-kirkwood/board-ts219.c (259e234608) Anyway, thanks for this work Sebastian. Cheers, a+ -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
