From: Maxime Ripard <maxime.rip...@free-electrons.com>
The IM pins of the HX8357 controller are used to define the interface used to
feed pixel stream to the LCD panel.
Most of the time, these pins are directly routed to either the ground or the VCC
to set their values.
Remove the need to assign GPIOs to these pins when we are in such a case.
Signed-off-by: Maxime Ripard <maxime.rip...@free-electrons.com>
---
drivers/video/backlight/hx8357.c | 53 +++++++++++++++++++++++-----------------
1 file changed, 31 insertions(+), 22 deletions(-)
diff --git a/drivers/video/backlight/hx8357.c b/drivers/video/backlight/hx8357.c
index a0482b5..69f5672 100644
--- a/drivers/video/backlight/hx8357.c
+++ b/drivers/video/backlight/hx8357.c
@@ -76,6 +76,7 @@ struct hx8357_data {
unsigned reset;
struct spi_device *spi;
int state;
+ u8 use_im_pins;
};
static u8 hx8357_seq_power[] = {
@@ -250,9 +251,11 @@ static int hx8357_lcd_init(struct lcd_device *lcdev)
* Set the interface selection pins to SPI mode, with three
* wires
*/
- gpio_set_value_cansleep(lcd->im_pins[0], 1);
- gpio_set_value_cansleep(lcd->im_pins[1], 0);
- gpio_set_value_cansleep(lcd->im_pins[2], 1);
+ if (lcd->use_im_pins) {
+ gpio_set_value_cansleep(lcd->im_pins[0], 1);
+ gpio_set_value_cansleep(lcd->im_pins[1], 0);
+ gpio_set_value_cansleep(lcd->im_pins[2], 1);
+ }
/* Reset the screen */
gpio_set_value(lcd->reset, 1);
@@ -424,26 +427,32 @@ static int hx8357_probe(struct spi_device *spi)
return -EINVAL;
}
- for (i = 0; i < HX8357_NUM_IM_PINS; i++) {
- lcd->im_pins[i] = of_get_named_gpio(spi->dev.of_node,
- "im-gpios", i);
- if (lcd->im_pins[i] == -EPROBE_DEFER) {
- dev_info(&spi->dev, "GPIO requested is not here yet,
deferring the probe\n");
- return -EPROBE_DEFER;
- }
- if (!gpio_is_valid(lcd->im_pins[i])) {
- dev_err(&spi->dev, "Missing dt property: im-gpios\n");
- return -EINVAL;
+ if (of_find_property(spi->dev.of_node, "im-gpios", NULL)) {
+ lcd->use_im_pins = 1;
+
+ for (i = 0; i < HX8357_NUM_IM_PINS; i++) {
+ lcd->im_pins[i] = of_get_named_gpio(spi->dev.of_node,
+ "im-gpios", i);
+ if (lcd->im_pins[i] == -EPROBE_DEFER) {
+ dev_info(&spi->dev, "GPIO requested is not here
yet, deferring the probe\n");
+ return -EPROBE_DEFER;
+ }
+ if (!gpio_is_valid(lcd->im_pins[i])) {
+ dev_err(&spi->dev, "Missing dt property:
im-gpios\n");
+ return -EINVAL;
+ }
+
+ ret = devm_gpio_request_one(&spi->dev, lcd->im_pins[i],
+ GPIOF_OUT_INIT_LOW,
+ "im_pins");
+ if (ret) {
+ dev_err(&spi->dev, "failed to request gpio %d:
%d\n",
+ lcd->im_pins[i], ret);
+ return -EINVAL;
+ }
}
-
- ret = devm_gpio_request_one(&spi->dev, lcd->im_pins[i],
- GPIOF_OUT_INIT_LOW, "im_pins");
- if (ret) {
- dev_err(&spi->dev, "failed to request gpio %d: %d\n",
- lcd->im_pins[i], ret);
- return -EINVAL;
- }
- }
+ } else
+ lcd->use_im_pins = 0;
lcdev = lcd_device_register("mxsfb", &spi->dev, lcd, &hx8357_ops);
if (IS_ERR(lcdev)) {
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
