Michal, All, [Sorry for duplicates, I inadvertently sent HTML]
On Tuesday 25 June 2013 11:21:53 Yann E. MORIN wrote: > On Tuesday 25 June 2013 10:55:20 Sedat Dilek wrote: > > Not sure what's going on, but I get this with today's Linux-Next. > > ( Yesterday's next-20130624 was OK. ) > > > > $ LANG=C LC_ALL=C yes "" | make oldconfig && LANG=C LC_ALL=C make > > silentoldconfig </dev/null > [--SNIP--] > > RapidIO support (RAPIDIO) [Y/n/?] y > > IDT Tsi721 PCI Express SRIO Controller support (RAPIDIO_TSI721) [Y/n/?] y > > Discovery timeout duration (seconds) (RAPIDIO_DISC_TIMEOUT) [30] 30 > > Enable RapidIO Input/Output Ports (RAPIDIO_ENABLE_RX_TX_PORTS) [N/y/?] n > > DMA Engine support for RapidIO (RAPIDIO_DMA_ENGINE) [Y/n/?] y > > RapidIO subsystem debug messages (RAPIDIO_DEBUG) [N/y/?] n > > Enumeration method [M/y/?] (NEW) aborted! > > > > Console input/output is redirected. Run 'make oldconfig' to update > > configuration. > > Yes, the same error as reported by Fengguang earlier: > http://marc.info/?l=linux-kbuild&m=137214773928335&w=4 > > And caused by (yet once more): > 8357b48: kconfig: fix randomising choice entries in presence of > KCONFIG_ALLCONFIG > > Basically, the issue is: > > - 'Enumeration method' is a tristate choice > - for tristate choices, it is possible to select zero, one or more of the > symbols in the choice > - if no symbol is selected (randomly or otherwise) in a tristate choice, > then the choice symbol itself has no assigned 'value' > - then silentoldconfig whines > > It worked so far as a side effect of another bug (which 8357b48 tries to > fix), and now this new one has been exposed. OK, after battling on this during my lunch-break, I now better understand the root cause. Consider this trivial Kconfig snippet: ---8<--- BEGIN Ktest ---8<--- config MODULES bool "Modules" choice tristate "test" config A tristate "A" config B tristate "B" config C tristate "C" endchoice ---8<--- END Ktest ---8<--- Now, this choice "test" is a tristate, so it can be either 'M' or 'Y'. But since this is a choice _prompt_ *and* it does not have a symbol associated, then its value is not stored in .config. On a sub-sequent run of a kconfig utility, the Ktest file is parsed, and the .config is read, associating read values to the symbols. But since the choice prompt has no symbol, no value is assigned to it, so it is believed to be new, and since it can be either 'M' or 'Y', it is asked for. Furthermore, even if the choice had a symbol, it would not be saved to the .config either. And we'd be back to square-1. > This one is starting to drive me crazy, really... :-( Yes, it is! (head spining frantically, toons-like) ;-) My lunch-break is over now, so more on this when I'mn back home, in ~6h. Regards, Yann E. MORIN. -- .-----------------.--------------------.------------------.--------------------. | Yann E. MORIN | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: | | +0/33 662376056 | Software Designer | \ / CAMPAIGN | ^ | | --==< O_o >==-- '------------.-------: X AGAINST | /e\ There is no | | http://ymorin.is-a-geek.org/ | (*_*) | / \ HTML MAIL | """ conspiracy. | '------------------------------'-------'------------------'--------------------' -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
