__spi_async(), which starts every SPI message transfer, initializes
the bits_per_word and max speed for every transfer in the message.
Since the conditional test in ep93xx_spi_process_transfer() will
always succeed just remove it and always call ep93xx_spi_chip_setup()
to configure the hardware for each transfer in the message.
Remove the redundant ep93xx_spi_chp_setup() in ep93xx_spi_process_transfer()
which just initializes the hardware to the "default" based on the SPI
device.
Signed-off-by: H Hartley Sweeten <hswee...@visionengravers.com>
Cc: Ryan Mallon <rmal...@gmail.com>
Cc: Mika Westerberg <mika.westerb...@iki.fi>
Cc: Mark Brown <broo...@kernel.org>
Cc: Grant Likely <grant.lik...@linaro.org>
---
drivers/spi/spi-ep93xx.c | 43 ++++++++++---------------------------------
1 file changed, 10 insertions(+), 33 deletions(-)
diff --git a/drivers/spi/spi-ep93xx.c b/drivers/spi/spi-ep93xx.c
index cad30b8..11e2b99 100644
--- a/drivers/spi/spi-ep93xx.c
+++ b/drivers/spi/spi-ep93xx.c
@@ -708,38 +708,20 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi
*espi,
struct spi_transfer *t)
{
struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi);
+ int err;
msg->state = t;
- /*
- * Handle any transfer specific settings if needed. We use
- * temporary chip settings here and restore original later when
- * the transfer is finished.
- */
- if (t->speed_hz || t->bits_per_word) {
- struct ep93xx_spi_chip tmp_chip = *chip;
-
- if (t->speed_hz) {
- int err;
-
- err = ep93xx_spi_calc_divisors(espi, &tmp_chip,
- t->speed_hz);
- if (err) {
- dev_err(&espi->pdev->dev,
- "failed to adjust speed\n");
- msg->status = err;
- return;
- }
- }
+ err = ep93xx_spi_calc_divisors(espi, chip, t->speed_hz);
+ if (err) {
+ dev_err(&espi->pdev->dev, "failed to adjust speed\n");
+ msg->status = err;
+ return;
+ }
- if (t->bits_per_word)
- tmp_chip.dss = bits_per_word_to_dss(t->bits_per_word);
+ chip->dss = bits_per_word_to_dss(t->bits_per_word);
- /*
- * Set up temporary new hw settings for this transfer.
- */
- ep93xx_spi_chip_setup(espi, &tmp_chip);
- }
+ ep93xx_spi_chip_setup(espi, chip);
espi->rx = 0;
espi->tx = 0;
@@ -783,9 +765,6 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi
*espi,
ep93xx_spi_cs_control(msg->spi, true);
}
}
-
- if (t->speed_hz || t->bits_per_word)
- ep93xx_spi_chip_setup(espi, chip);
}
/*
@@ -838,10 +817,8 @@ static void ep93xx_spi_process_message(struct ep93xx_spi
*espi,
espi->fifo_level = 0;
/*
- * Update SPI controller registers according to spi device and assert
- * the chipselect.
+ * Assert the chipselect.
*/
- ep93xx_spi_chip_setup(espi, spi_get_ctldata(msg->spi));
ep93xx_spi_cs_control(msg->spi, true);
list_for_each_entry(t, &msg->transfers, transfer_list) {
--
1.8.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
