On Wed, July 10, 2013, Doug Anderson wrote: > If the WAKEUP_INT is asserted at wakeup and not cleared, we'll end up > looping around forever. This has been seen to happen on exynos5420 > silicon despite the fact that we haven't enabled any wakeup events. > > Signed-off-by: Doug Anderson <diand...@chromium.org> > --- > Changes in v2: > - Use suspend_noirq as per James Hogan. > > drivers/mmc/host/dw_mmc-exynos.c | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/drivers/mmc/host/dw_mmc-exynos.c > b/drivers/mmc/host/dw_mmc-exynos.c > index f013e7e..36b9620 100644 > --- a/drivers/mmc/host/dw_mmc-exynos.c > +++ b/drivers/mmc/host/dw_mmc-exynos.c > @@ -30,6 +30,7 @@ > #define SDMMC_CLKSEL_TIMING(x, y, z) (SDMMC_CLKSEL_CCLK_SAMPLE(x) | \ > SDMMC_CLKSEL_CCLK_DRIVE(y) | \ > SDMMC_CLKSEL_CCLK_DIVIDER(z)) > +#define SDMMC_CLKSEL_WAKEUP_INT BIT(11) > > #define SDMMC_CMD_USE_HOLD_REG BIT(29) > > @@ -102,6 +103,27 @@ static int dw_mci_exynos_setup_clock(struct dw_mci *host) > return 0; > } > > +/** > + * dw_mci_exynos_resume_noirq - Exynos-specific resume code > + * > + * We have seen cases (at least on the exynos5420) where turning off the INT > + * power rail during suspend will leave the WAKEUP_INT bit in the CLKSEL > + * register asserted. This bit is 1 to indicate that it fired and we can > + * clear it by writing a 1 back. Clear it to prevent interrupts from going > off > + * constantly. > + */ As I know this bit is auto-cleared. Did you find the cause of this problem? How about your GPIO setting in sleep? Currently, we don't know why the problem is happened. At least, we should make it clear.
Thanks, Seungwon Jeon > + > +static int dw_mci_exynos_resume_noirq(struct dw_mci *host) > +{ > + u32 clksel; > + > + clksel = mci_readl(host, CLKSEL); > + if (clksel & SDMMC_CLKSEL_WAKEUP_INT) > + mci_writel(host, CLKSEL, clksel); > + > + return 0; > +} > + > static void dw_mci_exynos_prepare_command(struct dw_mci *host, u32 *cmdr) > { > /* > @@ -165,6 +187,7 @@ static const struct dw_mci_drv_data exynos_drv_data = { > .caps = exynos_dwmmc_caps, > .init = dw_mci_exynos_priv_init, > .setup_clock = dw_mci_exynos_setup_clock, > + .resume_noirq = dw_mci_exynos_resume_noirq, > .prepare_command = dw_mci_exynos_prepare_command, > .set_ios = dw_mci_exynos_set_ios, > .parse_dt = dw_mci_exynos_parse_dt, > -- > 1.8.3 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in > the body of a message to majord...@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/