linux-omap, linux-arm-list should also be CCed, Benoit needs to be addressed for allowing him to merge,
I have not done a proper schematics Vs data manual review yet (apologies on that), but, a couple of comments: On 08/13/2013 12:42 AM, Keerthy wrote: > The Patch adds nodes for TPS659038 PMIC for DRA7 boards. > > It is based on: > http://comments.gmane.org/gmane.linux.ports.arm.omap/102459. > > Documentation: Documentation/devicetree/bindings/mfd/palmas.txt > Documentation/devicetree/bindings/regulator/palmas-pmic.txt > > > Tested on DRA7 Board, 3.11-rc5 plus the above patch-set. > > Signed-off-by: Keerthy <j-keer...@ti.com> > --- > arch/arm/boot/dts/dra7-evm.dts | 118 > ++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 118 insertions(+) > > diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts > index b270e24..96f409f 100644 > --- a/arch/arm/boot/dts/dra7-evm.dts > +++ b/arch/arm/boot/dts/dra7-evm.dts > @@ -93,6 +93,124 @@ > pinctrl-names = "default"; > pinctrl-0 = <&i2c1_pins>; > clock-frequency = <400000>; > + > + tps659038: tps659038@58 { > + compatible = "ti,tps659038"; > + reg = <0x58>; > + interrupt-controller; > + #interrupt-cells = <2>; Where is the interrupt line to MPU? if it is not hooked up, why the interrupt controller? > + > + tps659038_pmic { > + compatible = "ti,tps659038-pmic"; > + > + regulators { > + smps123_reg: smps123 { > + /* VDD_MPU */ ^^ tab issue? > + regulator-name = "smps123"; > + regulator-min-microvolt = < > 600000>; > + regulator-max-microvolt = > <1500000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + smps45_reg: smps45 { > + /* VDD_DSPEVE */ > + regulator-name = "smps45"; > + regulator-min-microvolt = < > 600000>; > + regulator-max-microvolt = > <1310000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + smps6_reg: smps6 { > + /* VDD_GPU - over VDD_SMPS6 */ > + regulator-name = "smps6"; > + regulator-min-microvolt = > <600000>; > + regulator-max-microvolt = > <13100000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + smps7_reg: smps7 { > + /* VDDS_CORE */ > + regulator-name = "smps7"; > + regulator-min-microvolt = > <600000>; > + regulator-max-microvolt = > <1310000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + smps8_reg: smps8 { > + /* VDD_IVAHD */ > + regulator-name = "smps8"; > + regulator-min-microvolt = < > 600000>; > + regulator-max-microvolt = > <1310000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + smps9_reg: smps9 { > + /* VDD_1V8 */ > + regulator-name = "smps9"; > + regulator-min-microvolt = > <1800000>; > + regulator-max-microvolt = > <1800000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + ldo1_reg: ldo1 { > + /* LDO1_OUT --> SDIO */ > + regulator-name = "ldo1"; > + regulator-min-microvolt = > <1800000>; > + regulator-max-microvolt = > <3300000>; > + }; > + > + ldo2_reg: ldo2 { > + /* VDD_RTCIO */ > + regulator-name = "ldo2"; > + regulator-min-microvolt = > <3300000>; > + regulator-max-microvolt = > <3300000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + ldo3_reg: ldo3 { > + /* VDDA_1V8 PHYs */ > + regulator-name = "ldo3"; > + regulator-min-microvolt = > <1800000>; > + regulator-max-microvolt = > <1800000>; > + }; > + > + ldo9_reg: ldo9 { > + /* VDD_RTC */ > + regulator-name = "ldo9"; > + regulator-min-microvolt = > <1000000>; > + regulator-max-microvolt = > <1000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldoln_reg: ldoln { > + /* VDDA_1v8: PLLs */ > + regulator-name = "ldoln"; > + regulator-min-microvolt = > <1800000>; > + regulator-max-microvolt = > <1800000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + ldousb_reg: ldousb { > + /* VDDA_3V_USB: VDDA_USBHS33 */ > + regulator-name = "ldousb"; > + regulator-min-microvolt = > <3250000>; > + regulator-max-microvolt = > <3250000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + }; > + }; > + }; Who are using these LDOs? Example SDIO LDO should be linked up with MMC instance, no? how about the PLLs and PHYs? > }; > > &i2c2 { > -- Regards, Nishanth Menon -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
