Correct spelling typos in Documentations/devicetree/bindings Signed-off-by: Masanari Iida <standby2...@gmail.com>
--- Documentation/devicetree/bindings/gpio/mrvl-gpio.txt | 2 +- Documentation/devicetree/bindings/mfd/s2mps11.txt | 2 +- Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt | 2 +- Documentation/devicetree/bindings/video/atmel,lcdc.txt | 4 ++-- 4 files changed, 5 insertions(+), 5 deletions(-) diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 6641626..99daf57 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -12,7 +12,7 @@ Required properties: gpio_mux. - interrupt-names : Should be the names of irq resources. Each interrupt uses its own interrupt name, so there should be as many interrupt names - as referenced interrups. + as referenced interrupts. - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index c9332c6..31f952f 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -41,7 +41,7 @@ sub-node should be of the format as listed below. regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us - BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly + BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly regulator-ramp-delay = <0> can be used for them to disable ramp delay. In absence of regulator-ramp-delay property, default ramp delay will be used. diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index cdcebea..5486655 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt @@ -16,7 +16,7 @@ Required Properties: each child-node representing a supported slot. There should be atleast one child node representing a card slot. The name of the child node representing the slot is recommended to be slot@n where n is the unique number of the slot - connnected to the controller. The following are optional properties which + connected to the controller. The following are optional properties which can be included in the slot child node. * reg: specifies the physical slot number. The valid values of this diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt index 1ec175e..47981dd 100644 --- a/Documentation/devicetree/bindings/video/atmel,lcdc.txt +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt @@ -39,8 +39,8 @@ Atmel LCDC Display ----------------------------------------------------- Required properties (as per of_videomode_helper): - - atmel,dmacon: dma controler configuration - - atmel,lcdcon2: lcd controler configuration + - atmel,dmacon: dma controller configuration + - atmel,lcdcon2: lcd controller configuration - atmel,guard-time: lcd guard time (Delay in frame periods) - bits-per-pixel: lcd panel bit-depth. -- 1.8.4.rc3.2.g2c2b664 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/