On 26/09/13 15:02, Thierry Reding wrote: > On Thu, Sep 26, 2013 at 01:13:18PM +0300, Tomi Valkeinen wrote: >> On 11/09/13 14:40, Mike Dunn wrote: >>> On 09/10/2013 10:21 AM, Thierry Reding wrote: >> >>>> Do you have a real setup that actually needs multiple GPIOs? Usually >>>> such a setup requires some kind of timing or other additional constraint >>>> which can't be represented by this simple binding. >>>> >>>> Looking at the Palm Treo code it seems like the reason why multiple >>>> GPIOs are needed is because one is to enable the backlight, while the >>>> other is in fact used to enable the LCD panel. >>> >>> >>> There are actually four GPIOs involved! (There is an embarrasingly horrible >>> hack in arch/arm/mach-pxa/palmtreo.c that handles the others.) One is >>> almost >>> certainly simply backlight power. The other three are probably LCD related. >> >> When you say "power", do you mean the gpio enables a regulator to feed >> power to the backlight? If so, wouldn't that be a regulator, not gpio, >> from the bl driver's point of view? >> >> Generally speaking, this same problem appears in many places, but for >> some reason especially in display. I'm a bit hesitant in adding "free >> form" gpio/regulator support for drivers, as, as Thierry pointed out, >> there are often timing requirements, or sometimes the gpios are >> inverted, or sometimes the gpio is, in fact, a reset gpio, where you'll >> assert the gpio for a short moment only. > > I sent out another series a few days ago that somewhat obsoletes this > patch. What it does is basically add a single enable GPIO that can be > used to turn the backlight on and off. In a separate patch, support is > added for a power regulator. The combination of both should be able to > cover the majority of use-cases.
But Mike's case required 4 GPIOs? Or can that be reduced to one gpio and one regulator? > That series doesn't handle any timing requirements, but again, for the > majority of the setups supported by a power supply and enable GPIO the > timing doesn't matter. > >> I haven't seen new versions for the power sequences framework (without >> DT support), I think it could help us here a bit by simplifying how we >> present the sequences inside the driver. But we still need multiple >> drivers or the same driver supporting multiple devices. > > I'm not sure if power sequences will be very helpful here. There was an > attempt to get those merged, but the patches were NAKed in the end. I'm > not aware of any work currently being done on them. I thought the NAK was for the DT parts, not for the sequences as such. I don't remember anyone shooting down the idea of defining power sequences inside a driver. > But as I said above, the combination of an enable GPIO and power supply > should be enough to get a lot of use-cases supported. Yep. >> And I also think that the model where we have just one driver for, say, >> backlight may not be enough. There may be multiple hardware components, >> that used together will generate the backlight. And each component >> requires specific management. > > I'm not sure what other components you are talking about here. Can you > elaborate? I don't have any specific case in mind, and maybe these are quite rare. But there could be some kind of mix of muxes, regulators, gpios and whatnot that need to be managed in certain way to make backlight (or display) work. I'm making this up, so I'm not sure if this is sensible, but consider a board where there's a mux to select where a backlight gets its PWM input, and the mux is controlled via i2c. And maybe insert some kind of level shifter in between, enabled with a GPIO. And some third component, as this hypothetical board is a development board, and hardware people seem to love to make bizarre designs, that work in theory but the SW is almost impossible to design... So to enable the backlight, we might need to do multiple different things, depending on which components this particular board has. Especially for a mux controlled via i2c it would make sense to have a separate driver. Having just a single backlight driver might not be enough. Sometimes, or hopefully often, that kind of complexity can be hidden behind common frameworks. For example, enabling a gpio could result in the gpio driver enabling a regulator, sending i2c messages, or whatever. But I don't think that's possible in all cases. Anyway, this was really more of "thinking out loud" than any suggestion. Tomi
signature.asc
Description: OpenPGP digital signature
