On Wed, 2013-12-04 at 19:50 +0900, Chanwoo Choi wrote:
> Hi Krzysztof,
>
> On 12/04/2013 07:40 PM, Krzysztof Kozlowski wrote:
> > Add document describing device tree bindings for MAX14577 MFD driver.
> >
> > Signed-off-by: Krzysztof Kozlowski <k.kozlow...@samsung.com>
> > Signed-off-by: Kyungmin Park <kyungmin.p...@samsung.com>
> > ---
> > Documentation/devicetree/bindings/mfd/max14577.txt | 48
> > ++++++++++++++++++++
> > 1 file changed, 48 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/mfd/max14577.txt
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt
> > b/Documentation/devicetree/bindings/mfd/max14577.txt
> > new file mode 100644
> > index 000000000000..f4fd16360b6b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mfd/max14577.txt
> > @@ -0,0 +1,48 @@
> > +MAXIM MAX14577 multi-function device
> > +
> > +MAX14577 is a Multi-function device with Micro-USB Interface Circuit, Li+
> > +Battery Charger and SFOUT LDO output for powering USB devices. It is
> > +interfaced to host controller using I2C.
> > +
> > +Required properties:
> > +- compatible : Must be "maxim,max14577".
> > +- reg : I2C slave address for the max14577 chip.
> > +- interrupts : IRQ line for the max14577 chip.
> > +- interrupt-parent : The parent interrupt controller.
> > +
> > +Optional nodes:
> > +- regulators :
> > + Required child node properties:
> > + - compatible : "maxim,max14577-regulator"
> > +
> > + Optional child nodes:
> > + Each child node representing a regulator, following standard regulator
> > + bindings. Valid names for a regulator are: "CHARGER" and "SAFEOUT".
> > + The SAFEOUT is a constant voltage regulator so there is no need to
> > specify
> > + voltages for it.
> > +
> > + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt
> > +
> > +Example:
> > + max14577@25 {
> > + compatible = "maxim,max14577";
> > + reg = <0x25>;
> > + interrupt-parent = <&gpx1>;
> > + interrupts = <5 0>;
> > +
> > + regulators {
> > + compatible = "maxim,max14577-regulator";
> > +
> > + safeout_reg: safeout@1 {
> > + regulator-compatible = "SAFEOUT";
> > + regulator-name = "SAFEOUT";
> > + };
> > + charger_reg: charger@0 {
> > + regulator-compatible = "CHARGER";
> > + regulator-name = "CHARGER";
> > + regulator-min-microamp = <90000>;
> > + regulator-max-microamp = <950000>;
> > + regulator-boot-on;
> > + };
> > + };
>
> I prefer to add dt data about max14577-muic on following:
> If extcon consumer driver need to use muic device, dts should provide
> following dt data.
>
> muic: max14577-muic {
> compatible = "maxim, max14577-muic";
> };
> > + };
> >
> For example,
> If fuel-gauge want to use extcon subsystem, dt data of fuel-gauge add
> 'extcon' property as following:
>
> fuel-gague@ {
> compatible = "...";
> extcon = <&muic>;
> }
>
Hi,
The extcon driver itself does not use the binding. It is only needed for
consumers. Is it a common practice to add to documentation such notice
for consumers only?
Best regards,
Krzysztof
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
