Hi,
A few comments, see below please.
2013-12-07 05:52, Gary Rookard:
This is the fifth patch of a series.
Signed-off-by: Gary Alan Rookard <garyrook...@gmail.com>
---
On branch staging-next
drivers/staging/bcm/DDRInit.c | 270 +++++++++++++++++++++---------------------
1 file changed, 135 insertions(+), 135 deletions(-)
diff --git a/drivers/staging/bcm/DDRInit.c b/drivers/staging/bcm/DDRInit.c
index cb4dd53..1a08b17 100644
--- a/drivers/staging/bcm/DDRInit.c
+++ b/drivers/staging/bcm/DDRInit.c
@@ -5,15 +5,15 @@
#define DDR_DUMP_INTERNAL_DEVICE_MEMORY 0xBFC02B00
#define MIPS_CLOCK_REG 0x0f000820
- //DDR INIT-133Mhz
-#define T3_SKIP_CLOCK_PROGRAM_DUMP_133MHZ 12 //index for 0x0F007000
-static struct bcm_ddr_setting asT3_DDRSetting133MHz[] = {// # DPLL Clock
Setting
+ /* DDR INIT-133Mhz */
+#define T3_SKIP_CLOCK_PROGRAM_DUMP_133MHZ 12 /* index for 0x0F00700 */0
+static struct bcm_ddr_setting asT3_DDRSetting133MHz[] = { /* # DPLL Clock
Setting */
Why not remove the '#'? It is useless and never used anywhere else.
There is a /0 after... Have you build-test it?
@@ -29,17 +29,17 @@ static struct bcm_ddr_setting asT3_DDRSetting133MHz[] = {//
# DPLL Clock Se
{0x0F007010, 0x01000000},
{0x0F007014, 0x01000100},
{0x0F007018, 0x01000000},
- {0x0F00701c, 0x01020001},// POP - 0x00020001 Normal 0x01020001
- {0x0F007020, 0x04030107}, //Normal - 0x04030107 POP - 0x05030107
+ {0x0F00701c, 0x01020001},/* POP - 0x00020001 Normal 0x01020001 */
+ {0x0F007020, 0x04030107}, /* Normal - 0x04030107 POP - 0x05030107 */
{0x0F007024, 0x02000007},
{0x0F007028, 0x02020202},
- {0x0F00702c, 0x0206060a},//ROB- 0x0205050a,//0x0206060a
+ {0x0F00702c, 0x0206060a},/* ROB- 0x0205050a,0x0206060a */
{0x0F007030, 0x05000000},
{0x0F007034, 0x00000003};
- {0x0F007038, 0x110a0200},//ROB - 0x110a0200,//0x180a0200,// 0x1f0a0200
- {0x0F00703C, 0x02101010},//ROB - 0x02101010,//0x02101018},
- {0x0F007040, 0x45751200},//ROB - 0x45751200,//0x450f1200},
- {0x0F007044, 0x110a0d00},//ROB - 0x110a0d00//0x111f0d00
+ {0x0F007038, 0x110a0200},/* ROB - 0x110a0200,0x180a0200,0x1f0a0200 */
+ {0x0F00703C, 0x02101010},/* ROB - 0x02101010,0x02101018}, */
+ {0x0F007040, 0x45751200},/* ROB - 0x45751200,0x450f1200}, */
+ {0x0F007044, 0x110a0d00},/*ROB - 0x110a0d00.0x111f0d00 */
No space after '/*'
@@ -112,19 +112,19 @@ static struct bcm_ddr_setting asT3_DDRSetting80MHz[] =
{// # DPLL Clock Settin
{0x0F007080, 0x00000000},
{0x0F007084, 0x00000000},
{0x0F007094, 0x00000104},
- //# Enable start bit within memory
controller
+ /*# Enable start bit within memory
controller */
Again, no space and there is that '#' which looks pretty bad.
--
Regards,
Levente Kurusa
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
