These bindings can be used to register Maxim ModelGauge ICs fuel gauge
(MAX17040/41/43/44/48/49/58/59)
Signed-off-by: Vladimir Barinov <vladimir.bari...@cogentembedded.com>
---
Documentation/devicetree/bindings/power_supply/modelgauge_battery.txt | 82
++++++++++
1 file changed, 82 insertions(+)
Index:
battery-2.6/Documentation/devicetree/bindings/power_supply/modelgauge_battery.txt
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++
battery-2.6/Documentation/devicetree/bindings/power_supply/modelgauge_battery.txt
2014-01-09 15:09:38.035138887 +0400
@@ -0,0 +1,82 @@
+modelgauge_battery
+~~~~~~~~~~~~~~~~~~
+
+Required properties:
+ - compatible : should contain one of the following:
+ - "maxim,max17040" for MAX17040
+ - "maxim,max17041" for MAX17041
+ - "maxim,max17043" for MAX17043
+ - "maxim,max17044" for MAX17044
+ - "maxim,max17048" for MAX17048
+ - "maxim,max17049" for MAX17049
+ - "maxim,max17058" for MAX17058
+ - "maxim,max17059" for MAX17059
+
+Optional properties:
+ - maxim,empty_alert_threshold : Capacity threshold where an interrupt is
+ generated on the ALRT pin;
+
+ - soc_change_alert : /* alert for 1% soc change */
+ - hibernate_threshold : Hibernate threshold (crate), where IC
+ enters hibernate mode
+ - active_threshold : Active threshold (mV), where IC exits
+ hibernate mode
+ - undervoltage : Voltage (mV), when IC alerts while
battery
+ voltage less then undervoltage
+ - overvoltage : Voltage (mV), when IC alerts while battery
+ voltage greater then overvoltage
+ - maxim,resetvoltage : Voltage threshold (mV) below which the IC
+ resets itself. Used to detect battery removal
+ and reinsertion;
+ - maxim,empty_adjustment : Capacity charge empty design value;
+ - maxim,full_adjustment : Capacity charge full design value;
+ - maxim,rcomp0 : ModelGauge RCOMP parameter, used for
+ temperature compensation;
+ - maxim,temp_co_up : ModelGauge TempCoUp parameter, used for
+ temperature compensation;
+ - maxim,temp_co_down : ModelGauge TempCoDown parameter, used for
+ temperature compensation;
+ - maxim,ocvtest : ModelGauge OCVTest parameter, used for
+ verification of Custom Model calibration data
+ loaded into IC RAM;
+ - maxim,soc_check_a : ModelGauge SOCCheckA parameter, used for
+ verification of Custom Model calibration data
+ loaded into IC RAM;
+ - maxim,soc_check_b : ModelGauge SOCCheckB parameter, used for
+ verification of Custom Model calibration data
+ loaded into IC RAM;
+ - maxim,bits : ModelGauge Bits parameter, used as
+ scaling parameter in Custom Model algorithm;
+ - maxim,model_data : ModelGauge ModelData data,
+ Custom Model calibration data.
+
+Example:
+
+modelgauge@36 {
+ compatible = "maxim,max17058";
+ reg = <0x36>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <107 0x2>;
+
+ maxim,empty_alert_threshold = /bits/ 8 <15>;
+ maxim,resetvoltage = /bits/ 16 <0>;
+ maxim,empty_adjustment = /bits/ 8 <0>;
+ maxim,full_adjustment = /bits/ 8 <100>;
+ maxim,rcomp0 = /bits/ 8 <175>;
+ maxim,temp_co_up = <(-1100)>;
+ maxim,temp_co_down = <(-4000)>;
+ maxim,ocvtest = /bits/ 16 <56144>;
+ maxim,soc_check_a = /bits/ 8 <241>;
+ maxim,soc_check_b = /bits/ 8 <243>;
+ maxim,bits = /bits/ 8 <19>;
+
+ maxim,model_data = /bits/ 8 <
+ 0x9B 0x70 0xAB 0x30 0xB5 0xA0 0xB9 0xD0
+ 0xBB 0xA0 0xBC 0x00 0xBC 0xB0 0xBD 0x00
+ 0xBD 0x60 0xBE 0x40 0xBF 0x40 0xC1 0xF0
+ 0xC5 0x60 0xC8 0xA0 0xCD 0x00 0xD1 0x50
+ 0x00 0xE0 0x01 0x80 0x18 0x60 0x1C 0x20
+ 0x54 0x00 0x6A 0xC0 0x79 0x20 0x65 0xC0
+ 0x0B 0xE0 0x2A 0xC0 0x1D 0x00 0x17 0xE0
+ 0x15 0xE0 0x11 0xE0 0x11 0x00 0x11 0x00>;
+};
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
