PHY reset is necessary after some hw settings. However, it would
cause the linking down, and so does the set_speed function. Combine
the PHY reset with set_speed function. That could reduce the frequency
of linking down and accessing the PHY register.
Signed-off-by: Hayes Wang <hayesw...@realtek.com>
---
drivers/net/usb/r8152.c | 57 ++++++++++++++++++++++++++++++++++++++-----------
1 file changed, 45 insertions(+), 12 deletions(-)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index c7bae39..b3155da 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -436,6 +436,7 @@ enum rtl8152_flags {
RTL8152_SET_RX_MODE,
WORK_ENABLE,
RTL8152_LINK_CHG,
+ PHY_RESET,
};
/* Define these values to match your device */
@@ -1796,6 +1797,29 @@ static void r8152_power_cut_en(struct r8152 *tp, bool
enable)
}
+static void rtl_phy_reset(struct r8152 *tp)
+{
+ u16 data;
+ int i;
+
+ clear_bit(PHY_RESET, &tp->flags);
+
+ data = r8152_mdio_read(tp, MII_BMCR);
+
+ /* don't reset again before the previous one complete */
+ if (data & BMCR_RESET)
+ return;
+
+ data |= BMCR_RESET;
+ r8152_mdio_write(tp, MII_BMCR, data);
+
+ for (i = 0; i < 50; i++) {
+ msleep(20);
+ if ((r8152_mdio_read(tp, MII_BMCR) & BMCR_RESET) == 0)
+ break;
+ }
+}
+
static void rtl_clear_bp(struct r8152 *tp)
{
ocp_write_dword(tp, MCU_TYPE_PLA, PLA_BP_0, 0);
@@ -1854,6 +1878,7 @@ static void r8152b_hw_phy_cfg(struct r8152 *tp)
}
r8152b_disable_aldps(tp);
+ set_bit(PHY_RESET, &tp->flags);
}
static void r8152b_exit_oob(struct r8152 *tp)
@@ -2042,6 +2067,8 @@ static void r8153_hw_phy_cfg(struct r8152 *tp)
data = sram_read(tp, SRAM_10M_AMP2);
data |= AMP_DN;
sram_write(tp, SRAM_10M_AMP2, data);
+
+ set_bit(PHY_RESET, &tp->flags);
}
static void r8153_u1u2en(struct r8152 *tp, bool enable)
@@ -2295,12 +2322,26 @@ static int rtl8152_set_speed(struct r8152 *tp, u8
autoneg, u16 speed, u8 duplex)
bmcr = BMCR_ANENABLE | BMCR_ANRESTART;
}
+ if (test_bit(PHY_RESET, &tp->flags))
+ bmcr |= BMCR_RESET;
+
if (tp->mii.supports_gmii)
r8152_mdio_write(tp, MII_CTRL1000, gbcr);
r8152_mdio_write(tp, MII_ADVERTISE, anar);
r8152_mdio_write(tp, MII_BMCR, bmcr);
+ if (test_bit(PHY_RESET, &tp->flags)) {
+ int i;
+
+ clear_bit(PHY_RESET, &tp->flags);
+ for (i = 0; i < 50; i++) {
+ msleep(20);
+ if ((r8152_mdio_read(tp, MII_BMCR) & BMCR_RESET) == 0)
+ break;
+ }
+ }
+
out:
return ret;
@@ -2364,6 +2405,10 @@ static void rtl_work_func_t(struct work_struct *work)
if (test_bit(RTL8152_SET_RX_MODE, &tp->flags))
_rtl8152_set_rx_mode(tp->netdev);
+
+ if (test_bit(PHY_RESET, &tp->flags))
+ rtl_phy_reset(tp);
+
out1:
return;
}
@@ -2459,7 +2504,6 @@ static void r8152b_enable_fc(struct r8152 *tp)
static void r8152b_init(struct r8152 *tp)
{
u32 ocp_data;
- int i;
rtl_clear_bp(tp);
@@ -2491,14 +2535,6 @@ static void r8152b_init(struct r8152 *tp)
r8152b_enable_aldps(tp);
r8152b_enable_fc(tp);
- r8152_mdio_write(tp, MII_BMCR, BMCR_RESET | BMCR_ANENABLE |
- BMCR_ANRESTART);
- for (i = 0; i < 100; i++) {
- udelay(100);
- if (!(r8152_mdio_read(tp, MII_BMCR) & BMCR_RESET))
- break;
- }
-
/* enable rx aggregation */
ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_USB_CTRL);
ocp_data &= ~RX_AGG_DISABLE;
@@ -2569,9 +2605,6 @@ static void r8153_init(struct r8152 *tp)
r8153_enable_eee(tp);
r8153_enable_aldps(tp);
r8152b_enable_fc(tp);
-
- r8152_mdio_write(tp, MII_BMCR, BMCR_RESET | BMCR_ANENABLE |
- BMCR_ANRESTART);
}
static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
--
1.8.4.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
