> Hello,
>
> I have MPC880 microprocessor based board with single 24C02 I2C EEPROM,
> connected to the I2C bus.
>
Yes, it is embedded, yes it is not INTEL arch ... but PLEASE - READ ON ! ;-)
>
> Currently booting of the board hangs in the I2C driver after invocation of
> interruptible_sleep_on( )
> function call in cpm_iic_tryaddress( ) function (in i2c-algo-8xx.c
> file).
>
> Is it appropriate to use the interruptible_sleep_on( ) function at the
> kernel booting stage ?
> (I personally do not think so - since such usage prevents further kernel
> booting - as observed).
> What should be done in this code to avoid sleeping forever - how to put
> time out on this sleep ?
>
> I presume that the usage of the interruptible_sleep_on( ) function would
> be appropriate if the
> I2C would be configured as a module (after the kernel booting is
> completed) ?
> Follow up question: is it really expected to do I2C initialization ONLY
> as a module after the kernel booting ?
> (is it documented anyplace ?)
>
> The (end of) log buffer shows following:
> ....
> <6>i2c /dev entries driver.
> <7>device class 'i2c-dev': registering.
> <7>bus i2c:add driver dev_driver.
> <7>i2c-core: driver dev_driver registered
> <6>i2c-rpx: i2c MPC8xx driver.
> <7>DEV: registering device: ID ='i2c-0'.
> <7>CLASS: registering class device: ID= 'i2c-0'.
> <7>i2c_adapter i2c-0:Registered as minor 0.
> <7>CLASS:registering class device: ID = 'i2c-0'
> <7>i2c_adapter i2c-0: registered as adapter #0.
> <4>cpm_iic_init() - iip=fa203c80.
> <4>cpm_iic_init[132] Install ISR for IRQ 16.
> <6>CPM interrupt c0105d90 replacing c01f7a8c.
> <3>request_irq() returned -22 for CPM vector 32.
> <6> i2c-algo-8xx.o: scanning bus m8xx........
> <4>cpm_iic_tryaddress(cpm=c019b9f8,addr=0).
> <4>iip fa203c80, dp_addr 0x800.
> <4>iic_tbase 2048, r_tbase 2048
> <4>about to sleep
> .ABOVE LINE IS THE LAST ENTRY IN THE LOG BUFFER - THE BOOT HANGS
> THEREAFTER ...
>
> Here is the fragment of the cpm_iic_tryaddress( ) function in
> i2c-algo-8xx.c,
> where the problem takes place:
> ....
> // save_flags(flags); cli();
> i2c->i2c_i2cer = 0xff;
> i2c->i2c_i2cmr = 0x13; /* Enable some interupts */
> i2c->i2c_i2mod = 1; /* Enable */
> i2c->i2c_i2com = 0x81; /* Start master */
> // restore_flags(flags);
>
> if (cpm_debug > 1) printk("about to sleep\n");
>
> /* wait for IIC transfer */
> interruptible_sleep_on(&iic_wait);
> if (signal_pending(current))
> return -EIO;
>
> if (cpm_debug > 1) printk("back from sleep\n");
>
> if (tbdf->cbd_sc & BD_SC_NAK) {
> if (cpm_debug > 1) printk("IIC try; no ack\n");
> return 0;
> }
>
> if (tbdf->cbd_sc & BD_SC_READY) {
> printk("IIC try; complete but tbuf ready\n");
> }
>
> return 1;
>
> ........
> Thanks,
> Best Regards,
> Alex
>
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
