Hi Krzysztof,
On 05/29/2014 05:51 PM, Krzysztof Kozlowski wrote:
> Hi Chanwoo,
>
> Few ideas below:
>
>
> On śro, 2014-05-28 at 20:10 +0900, Chanwoo Choi wrote:
>> This patch add S2MPU02 regulator device to existing S2MPS11 device driver
>> because of existing a litthe different between S2MPS1x and S2MPU02. The
>> S2MPU02
>
> Fix a typo and language:
> "because of little differences between S2MPS1x and S2MPU02"
OK, I'll fix it.
>
>
>> regulator device includes LDO[1-28] and BUCK[1-7].
>>
>> Signed-off-by: Chanwoo Choi <cw00.c...@samsung.com>
>>
>> ---
>> drivers/mfd/sec-core.c | 26 +++
>> drivers/regulator/s2mps11.c | 310
>> ++++++++++++++++++++++++++++++++++--
>> include/linux/mfd/samsung/s2mpu02.h | 201 +++++++++++++++++++++++
>> 3 files changed, 521 insertions(+), 16 deletions(-)
>> create mode 100644 include/linux/mfd/samsung/s2mpu02.h
>>
>
> (...)
>
>> diff --git a/drivers/regulator/s2mps11.c b/drivers/regulator/s2mps11.c
>> index 02e2fb2..064d44b 100644
>> --- a/drivers/regulator/s2mps11.c
>> +++ b/drivers/regulator/s2mps11.c
>> @@ -31,6 +31,7 @@
>> #include <linux/mfd/samsung/core.h>
>> #include <linux/mfd/samsung/s2mps11.h>
>> #include <linux/mfd/samsung/s2mps14.h>
>> +#include <linux/mfd/samsung/s2mpu02.h>
>>
>> struct s2mps11_info {
>> unsigned int rdev_num;
>> @@ -40,11 +41,16 @@ struct s2mps11_info {
>> int ramp_delay16;
>> int ramp_delay7810;
>> int ramp_delay9;
>> +
>> + enum sec_device_type dev_type;
>> +
>> /*
>> - * One bit for each S2MPS14 regulator whether the suspend mode
>> + * One bit for each S2MPS14/S2MPU02 regulator whether the suspend mode
>> * was enabled.
>> */
>> unsigned int s2mps14_suspend_state:30;
>> + unsigned long long s2mpu02_suspend_state:35;
>> +
>
> Why do not re-use the already present 's2mps14_suspend_state' field?
> Change it to 'unsigned long long:35' and use it for both s2mps14 and
> s2mpu02 suspend states?
OK, I'll fix it.
>
>
>> /* Array of size rdev_num with GPIO-s for external sleep control */
>> int *ext_control_gpio;
>> };
>> @@ -415,12 +421,24 @@ static int s2mps14_regulator_enable(struct
>> regulator_dev *rdev)
>> struct s2mps11_info *s2mps11 = rdev_get_drvdata(rdev);
>> unsigned int val;
>>
>> - if (s2mps11->s2mps14_suspend_state & (1 << rdev_get_id(rdev)))
>> - val = S2MPS14_ENABLE_SUSPEND;
>> - else if (gpio_is_valid(s2mps11->ext_control_gpio[rdev_get_id(rdev)]))
>> - val = S2MPS14_ENABLE_EXT_CONTROL;
>> - else
>> - val = rdev->desc->enable_mask;
>> + switch (s2mps11->dev_type) {
>> + case S2MPS14X:
>> + if (s2mps11->s2mps14_suspend_state & (1 << rdev_get_id(rdev)))
>> + val = S2MPS14_ENABLE_SUSPEND;
>> + else if
>> (gpio_is_valid(s2mps11->ext_control_gpio[rdev_get_id(rdev)]))
>> + val = S2MPS14_ENABLE_EXT_CONTROL;
>> + else
>> + val = rdev->desc->enable_mask;
>> + break;
>> + case S2MPU02:
>> + if (s2mps11->s2mpu02_suspend_state & (1 << rdev_get_id(rdev)))
>> + val = S2MPU02_ENABLE_SUSPEND;
>> + else
>> + val = rdev->desc->enable_mask;
>> + break;
>> + default:
>> + return -EINVAL;
>> + };
>>
>> return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
>> rdev->desc->enable_mask, val);
>> @@ -431,16 +449,44 @@ static int
>> s2mps14_regulator_set_suspend_disable(struct regulator_dev *rdev)
>> int ret;
>> unsigned int val;
>> struct s2mps11_info *s2mps11 = rdev_get_drvdata(rdev);
>> + int rdev_id = rdev_get_id(rdev);
>>
>> - /* LDO3 should be always on and does not support suspend mode */
>> - if (rdev_get_id(rdev) == S2MPS14_LDO3)
>> - return 0;
>> + /* Below LDO should be always on or does not support suspend mode. */
>> + switch (s2mps11->dev_type) {
>> + case S2MPS14X:
>> + switch (rdev_id) {
>> + case S2MPS14_LDO3:
>> + return 0;
>> + };
>> + case S2MPU02:
>> + switch (rdev_id) {
>> + case S2MPU02_LDO13:
>> + case S2MPU02_LDO14:
>> + case S2MPU02_LDO15:
>> + case S2MPU02_LDO16:
>> + case S2MPU02_LDO17:
>> + case S2MPU02_BUCK7:
>> + return 0;
>> + };
>> + default:
>> + return -EINVAL;
>> + };
>>
>> ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val);
>> if (ret < 0)
>> return ret;
>>
>> - s2mps11->s2mps14_suspend_state |= (1 << rdev_get_id(rdev));
>> + switch (s2mps11->dev_type) {
>> + case S2MPS14X:
>> + s2mps11->s2mps14_suspend_state |= (1 << rdev_get_id(rdev));
>> + break;
>> + case S2MPU02:
>> + s2mps11->s2mpu02_suspend_state |= (1 << rdev_get_id(rdev));
>> + break;
>> + default:
>> + return -EINVAL;
>> + };
>> +
>> /*
>> * Don't enable suspend mode if regulator is already disabled because
>> * this would effectively for a short time turn on the regulator after
>> @@ -625,6 +671,233 @@ static int s2mps11_pmic_dt_parse(struct
>> platform_device *pdev,
>> return 0;
>> }
>>
>> +static int s2mpu02_set_ramp_delay(struct regulator_dev *rdev, int
>> ramp_delay)
>> +{
>> + unsigned int ramp_val, ramp_shift, ramp_reg;
>> +
>> + switch (rdev_get_id(rdev)) {
>> + case S2MPU02_BUCK1:
>> + ramp_shift = S2MPU02_BUCK1_RAMP_SHIFT;
>> + break;
>> + case S2MPU02_BUCK2:
>> + ramp_shift = S2MPU02_BUCK2_RAMP_SHIFT;
>> + break;
>> + case S2MPU02_BUCK3:
>> + ramp_shift = S2MPU02_BUCK3_RAMP_SHIFT;
>> + break;
>> + case S2MPU02_BUCK4:
>> + ramp_shift = S2MPU02_BUCK4_RAMP_SHIFT;
>> + break;
>> + default:
>> + return 0;
>> + }
>> + ramp_reg = S2MPU02_REG_RAMP1;
>> + ramp_val = get_ramp_delay(ramp_delay);
>> +
>> + return regmap_update_bits(rdev->regmap, ramp_reg,
>> + S2MPU02_BUCK1234_RAMP_MASK << ramp_shift,
>> + ramp_val << ramp_shift);
>> +}
>> +
>> +static struct regulator_ops s2mpu02_ldo_ops = {
>> + .list_voltage = regulator_list_voltage_linear,
>> + .map_voltage = regulator_map_voltage_linear,
>> + .is_enabled = regulator_is_enabled_regmap,
>> + .enable = s2mps14_regulator_enable,
>> + .disable = regulator_disable_regmap,
>> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
>> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
>> + .set_voltage_time_sel = regulator_set_voltage_time_sel,
>> + .set_suspend_disable = s2mps14_regulator_set_suspend_disable,
>> +};
>> +
>> +static struct regulator_ops s2mpu02_buck_ops = {
>> + .list_voltage = regulator_list_voltage_linear,
>> + .map_voltage = regulator_map_voltage_linear,
>> + .is_enabled = regulator_is_enabled_regmap,
>> + .enable = s2mps14_regulator_enable,
>> + .disable = regulator_disable_regmap,
>> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
>> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
>> + .set_voltage_time_sel = regulator_set_voltage_time_sel,
>> + .set_suspend_disable = s2mps14_regulator_set_suspend_disable,
>> + .set_ramp_delay = s2mpu02_set_ramp_delay,
>> +};
>> +
>> +#define regulator_desc_s2mpu02_ldo1(num) { \
>> + .name = "LDO"#num, \
>> + .id = S2MPU02_LDO##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_LDO_MIN_900MV, \
>> + .uV_step = S2MPU02_LDO_STEP_12_5MV, \
>> + .n_voltages = S2MPU02_LDO_N_VOLTAGES, \
>> + .vsel_reg = S2MPU02_REG_L1CTRL, \
>> + .vsel_mask = S2MPU02_LDO_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_L1CTRL, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_ldo2(num) { \
>> + .name = "LDO"#num, \
>> + .id = S2MPU02_LDO##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_LDO_MIN_1050MV, \
>> + .uV_step = S2MPU02_LDO_STEP_25MV, \
>> + .n_voltages = S2MPU02_LDO_N_VOLTAGES, \
>> + .vsel_reg = S2MPU02_REG_L2CTRL1, \
>> + .vsel_mask = S2MPU02_LDO_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_L2CTRL1, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_ldo3(num) { \
>> + .name = "LDO"#num, \
>> + .id = S2MPU02_LDO##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_LDO_MIN_900MV, \
>> + .uV_step = S2MPU02_LDO_STEP_12_5MV, \
>> + .n_voltages = S2MPU02_LDO_N_VOLTAGES, \
>> + .vsel_reg = S2MPU02_REG_L3CTRL + num - 3, \
>> + .vsel_mask = S2MPU02_LDO_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_L3CTRL + num - 3, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_ldo4(num) { \
>> + .name = "LDO"#num, \
>> + .id = S2MPU02_LDO##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_LDO_MIN_1050MV, \
>> + .uV_step = S2MPU02_LDO_STEP_25MV, \
>> + .n_voltages = S2MPU02_LDO_N_VOLTAGES, \
>> + .vsel_reg = S2MPU02_REG_L3CTRL + num - 3, \
>> + .vsel_mask = S2MPU02_LDO_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_L3CTRL + num - 3, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_ldo5(num) { \
>> + .name = "LDO"#num, \
>> + .id = S2MPU02_LDO##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_LDO_MIN_1600MV, \
>> + .uV_step = S2MPU02_LDO_STEP_50MV, \
>> + .n_voltages = S2MPU02_LDO_N_VOLTAGES, \
>> + .vsel_reg = S2MPU02_REG_L3CTRL + num - 3, \
>> + .vsel_mask = S2MPU02_LDO_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_L3CTRL + num - 3, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +
>> +#define regulator_desc_s2mpu02_buck1234(num) { \
>> + .name = "BUCK"#num, \
>> + .id = S2MPU02_BUCK##num, \
>> + .ops = &s2mpu02_buck_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_BUCK1234_MIN_600MV, \
>> + .uV_step = S2MPU02_BUCK1234_STEP_6_25MV, \
>> + .n_voltages = S2MPU02_BUCK_N_VOLTAGES, \
>> + .linear_min_sel = S2MPU02_BUCK1234_START_SEL, \
>> + .ramp_delay = S2MPU02_BUCK_RAMP_DELAY, \
>> + .vsel_reg = S2MPU02_REG_B1CTRL2 + (num - 1) * 2, \
>> + .vsel_mask = S2MPU02_BUCK_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_B1CTRL1 + (num - 1) * 2, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_buck5(num) { \
>> + .name = "BUCK"#num, \
>> + .id = S2MPU02_BUCK##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_BUCK5_MIN_1081_25MV, \
>> + .uV_step = S2MPU02_BUCK5_STEP_6_25MV, \
>> + .n_voltages = S2MPU02_BUCK_N_VOLTAGES, \
>> + .linear_min_sel = S2MPU02_BUCK5_START_SEL, \
>> + .ramp_delay = S2MPU02_BUCK_RAMP_DELAY, \
>> + .vsel_reg = S2MPU02_REG_B5CTRL2, \
>> + .vsel_mask = S2MPU02_BUCK_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_B5CTRL1, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_buck6(num) { \
>> + .name = "BUCK"#num, \
>> + .id = S2MPU02_BUCK##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_BUCK6_MIN_1700MV, \
>> + .uV_step = S2MPU02_BUCK6_STEP_2_50MV, \
>> + .n_voltages = S2MPU02_BUCK_N_VOLTAGES, \
>> + .linear_min_sel = S2MPU02_BUCK6_START_SEL, \
>> + .ramp_delay = S2MPU02_BUCK_RAMP_DELAY, \
>> + .vsel_reg = S2MPU02_REG_B6CTRL2, \
>> + .vsel_mask = S2MPU02_BUCK_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_B6CTRL1, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +#define regulator_desc_s2mpu02_buck7(num) { \
>> + .name = "BUCK"#num, \
>> + .id = S2MPU02_BUCK##num, \
>> + .ops = &s2mpu02_ldo_ops, \
>> + .type = REGULATOR_VOLTAGE, \
>> + .owner = THIS_MODULE, \
>> + .min_uV = S2MPU02_BUCK7_MIN_900MV, \
>> + .uV_step = S2MPU02_BUCK7_STEP_6_25MV, \
>> + .n_voltages = S2MPU02_BUCK_N_VOLTAGES, \
>> + .linear_min_sel = S2MPU02_BUCK7_START_SEL, \
>> + .ramp_delay = S2MPU02_BUCK_RAMP_DELAY, \
>> + .vsel_reg = S2MPU02_REG_B7CTRL2, \
>> + .vsel_mask = S2MPU02_BUCK_VSEL_MASK, \
>> + .enable_reg = S2MPU02_REG_B7CTRL1, \
>> + .enable_mask = S2MPU02_ENABLE_MASK \
>> +}
>> +
>> +static const struct regulator_desc s2mpu02_regulators[] = {
>> + regulator_desc_s2mpu02_ldo1(1),
>> + regulator_desc_s2mpu02_ldo2(2),
>> + regulator_desc_s2mpu02_ldo4(3),
>> + regulator_desc_s2mpu02_ldo5(4),
>> + regulator_desc_s2mpu02_ldo4(5),
>> + regulator_desc_s2mpu02_ldo3(6),
>> + regulator_desc_s2mpu02_ldo3(7),
>> + regulator_desc_s2mpu02_ldo4(8),
>> + regulator_desc_s2mpu02_ldo5(9),
>> + regulator_desc_s2mpu02_ldo3(10),
>> + regulator_desc_s2mpu02_ldo4(11),
>> + regulator_desc_s2mpu02_ldo5(12),
>> + regulator_desc_s2mpu02_ldo5(13),
>> + regulator_desc_s2mpu02_ldo5(14),
>> + regulator_desc_s2mpu02_ldo5(15),
>> + regulator_desc_s2mpu02_ldo5(16),
>> + regulator_desc_s2mpu02_ldo4(17),
>> + regulator_desc_s2mpu02_ldo5(18),
>> + regulator_desc_s2mpu02_ldo3(19),
>> + regulator_desc_s2mpu02_ldo4(20),
>> + regulator_desc_s2mpu02_ldo5(21),
>> + regulator_desc_s2mpu02_ldo5(22),
>> + regulator_desc_s2mpu02_ldo5(23),
>> + regulator_desc_s2mpu02_ldo4(24),
>> + regulator_desc_s2mpu02_ldo5(25),
>> + regulator_desc_s2mpu02_ldo4(26),
>> + regulator_desc_s2mpu02_ldo5(27),
>> + regulator_desc_s2mpu02_ldo5(28),
>> + regulator_desc_s2mpu02_buck1234(1),
>> + regulator_desc_s2mpu02_buck1234(2),
>> + regulator_desc_s2mpu02_buck1234(3),
>> + regulator_desc_s2mpu02_buck1234(4),
>> + regulator_desc_s2mpu02_buck5(5),
>> + regulator_desc_s2mpu02_buck6(6),
>> + regulator_desc_s2mpu02_buck7(7),
>> +};
>> +
>> static int s2mps11_pmic_probe(struct platform_device *pdev)
>> {
>> struct sec_pmic_dev *iodev = dev_get_drvdata(pdev->dev.parent);
>> @@ -634,15 +907,14 @@ static int s2mps11_pmic_probe(struct platform_device
>> *pdev)
>> struct s2mps11_info *s2mps11;
>> int i, ret = 0;
>> const struct regulator_desc *regulators;
>> - enum sec_device_type dev_type;
>>
>> s2mps11 = devm_kzalloc(&pdev->dev, sizeof(struct s2mps11_info),
>> GFP_KERNEL);
>> if (!s2mps11)
>> return -ENOMEM;
>>
>> - dev_type = platform_get_device_id(pdev)->driver_data;
>> - switch (dev_type) {
>> + s2mps11->dev_type = platform_get_device_id(pdev)->driver_data;
>> + switch (s2mps11->dev_type) {
>> case S2MPS11X:
>> s2mps11->rdev_num = ARRAY_SIZE(s2mps11_regulators);
>> regulators = s2mps11_regulators;
>> @@ -651,8 +923,13 @@ static int s2mps11_pmic_probe(struct platform_device
>> *pdev)
>> s2mps11->rdev_num = ARRAY_SIZE(s2mps14_regulators);
>> regulators = s2mps14_regulators;
>> break;
>> + case S2MPU02:
>> + s2mps11->rdev_num = ARRAY_SIZE(s2mpu02_regulators);
>> + regulators = s2mpu02_regulators;
>> + break;
>> default:
>> - dev_err(&pdev->dev, "Invalid device type: %u\n", dev_type);
>> + dev_err(&pdev->dev, "Invalid device type: %u\n",
>> + s2mps11->dev_type);
>> return -EINVAL;
>> };
>>
>> @@ -686,7 +963,7 @@ static int s2mps11_pmic_probe(struct platform_device
>> *pdev)
>> for (i = 0; i < s2mps11->rdev_num; i++)
>> rdata[i].name = regulators[i].name;
>>
>> - ret = s2mps11_pmic_dt_parse(pdev, rdata, s2mps11, dev_type);
>> + ret = s2mps11_pmic_dt_parse(pdev, rdata, s2mps11, s2mps11->dev_type);
>
> I think you can get rid of last parameter of s2mps11_pmic_dt_parse().
> The function already received a pointer to 'struct s2mps11_info' and it
> will be called after setting 's2mps11->dev_type' so the last parameter
> is not needed.
You're right. I'll fix it.
>
>> if (ret)
>> goto out;
>>
>> @@ -739,6 +1016,7 @@ out:
>> static const struct platform_device_id s2mps11_pmic_id[] = {
>> { "s2mps11-pmic", S2MPS11X},
>> { "s2mps14-pmic", S2MPS14X},
>> + { "s2mpu02-pmic", S2MPU02},
>> { },
>> };
>> MODULE_DEVICE_TABLE(platform, s2mps11_pmic_id);
>> diff --git a/include/linux/mfd/samsung/s2mpu02.h
>> b/include/linux/mfd/samsung/s2mpu02.h
>> new file mode 100644
>> index 0000000..98406f4
>> --- /dev/null
>> +++ b/include/linux/mfd/samsung/s2mpu02.h
>> @@ -0,0 +1,201 @@
>> +/*
>> + * s2mpu02.h
>> + *
>> + * Copyright (c) 2014 Samsung Electronics Co., Ltd
>> + * http://www.samsung.com
>> + *
>> + * This program is free software; you can redistribute it and/or modify it
>> + * under the terms of the GNU General Public License as published by the
>> + * Free Software Foundation; either version 2 of the License, or (at your
>> + * option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + */
>> +
>> +#ifndef __LINUX_MFD_S2MPU02_H
>> +#define __LINUX_MFD_S2MPU02_H
>> +
>> +/* S2MPU02 registers */
>> +enum S2MPU02_reg {
>> + S2MPU02_REG_ID,
>> + S2MPU02_REG_INT1,
>> + S2MPU02_REG_INT2,
>> + S2MPU02_REG_INT3,
>> + S2MPU02_REG_INT1M,
>> + S2MPU02_REG_INT2M,
>> + S2MPU02_REG_INT3M,
>> + S2MPU02_REG_ST1,
>> + S2MPU02_REG_ST2,
>> + S2MPU02_REG_PWRONSRC,
>> + S2MPU02_REG_OFFSRC,
>> + S2MPU02_REG_BU_CHG,
>> + S2MPU02_REG_RTCCTRL,
>> + S2MPU02_REG_PMCTRL1,
>> + S2MPU02_REG_RSVD1,
>> + S2MPU02_REG_RSVD2,
>> + S2MPU02_REG_RSVD3,
>> + S2MPU02_REG_RSVD4,
>> + S2MPU02_REG_RSVD5,
>> + S2MPU02_REG_RSVD6,
>> + S2MPU02_REG_RSVD7,
>> + S2MPU02_REG_WRSTEN,
>> + S2MPU02_REG_RSVD8,
>> + S2MPU02_REG_RSVD9,
>> + S2MPU02_REG_RSVD10,
>> + S2MPU02_REG_B1CTRL1,
>> + S2MPU02_REG_B1CTRL2,
>> + S2MPU02_REG_B2CTRL1,
>> + S2MPU02_REG_B2CTRL2,
>> + S2MPU02_REG_B3CTRL1,
>> + S2MPU02_REG_B3CTRL2,
>> + S2MPU02_REG_B4CTRL1,
>> + S2MPU02_REG_B4CTRL2,
>> + S2MPU02_REG_B5CTRL1,
>> + S2MPU02_REG_B5CTRL2,
>> + S2MPU02_REG_B5CTRL3,
>> + S2MPU02_REG_B5CTRL4,
>> + S2MPU02_REG_B5CTRL5,
>> + S2MPU02_REG_B6CTRL1,
>> + S2MPU02_REG_B6CTRL2,
>> + S2MPU02_REG_B7CTRL1,
>> + S2MPU02_REG_B7CTRL2,
>> + S2MPU02_REG_RAMP1,
>> + S2MPU02_REG_RAMP2,
>> + S2MPU02_REG_L1CTRL,
>> + S2MPU02_REG_L2CTRL1,
>> + S2MPU02_REG_L2CTRL2,
>> + S2MPU02_REG_L2CTRL3,
>> + S2MPU02_REG_L2CTRL4,
>> + S2MPU02_REG_L3CTRL,
>> + S2MPU02_REG_L4CTRL,
>> + S2MPU02_REG_L5CTRL,
>> + S2MPU02_REG_L6CTRL,
>> + S2MPU02_REG_L7CTRL,
>> + S2MPU02_REG_L8CTRL,
>> + S2MPU02_REG_L9CTRL,
>> + S2MPU02_REG_L10CTRL,
>> + S2MPU02_REG_L11CTRL,
>> + S2MPU02_REG_L12CTRL,
>> + S2MPU02_REG_L13CTRL,
>> + S2MPU02_REG_L14CTRL,
>> + S2MPU02_REG_L15CTRL,
>> + S2MPU02_REG_L16CTRL,
>> + S2MPU02_REG_L17CTRL,
>> + S2MPU02_REG_L18CTRL,
>> + S2MPU02_REG_L19CTRL,
>> + S2MPU02_REG_L20CTRL,
>> + S2MPU02_REG_L21CTRL,
>> + S2MPU02_REG_L22CTRL,
>> + S2MPU02_REG_L23CTRL,
>> + S2MPU02_REG_L24CTRL,
>> + S2MPU02_REG_L25CTRL,
>> + S2MPU02_REG_L26CTRL,
>> + S2MPU02_REG_L27CTRL,
>> + S2MPU02_REG_L28CTRL,
>> + S2MPU02_REG_LDODSCH1,
>> + S2MPU02_REG_LDODSCH2,
>> + S2MPU02_REG_LDODSCH3,
>> + S2MPU02_REG_LDODSCH4,
>> + S2MPU02_REG_SELMIF,
>> + S2MPU02_REG_RSVD11,
>> + S2MPU02_REG_RSVD12,
>> + S2MPU02_REG_RSVD13,
>> + S2MPU02_REG_DVSSEL,
>> + S2MPU02_REG_DVSPTR,
>> + S2MPU02_REG_DVSDATA,
>> +};
>> +
>> +/* S2MPU02 regulator ids */
>> +enum S2MPU02_regulators {
>> + S2MPU02_LDO1,
>> + S2MPU02_LDO2,
>> + S2MPU02_LDO3,
>> + S2MPU02_LDO4,
>> + S2MPU02_LDO5,
>> + S2MPU02_LDO6,
>> + S2MPU02_LDO7,
>> + S2MPU02_LDO8,
>> + S2MPU02_LDO9,
>> + S2MPU02_LDO10,
>> + S2MPU02_LDO11,
>> + S2MPU02_LDO12,
>> + S2MPU02_LDO13,
>> + S2MPU02_LDO14,
>> + S2MPU02_LDO15,
>> + S2MPU02_LDO16,
>> + S2MPU02_LDO17,
>> + S2MPU02_LDO18,
>> + S2MPU02_LDO19,
>> + S2MPU02_LDO20,
>> + S2MPU02_LDO21,
>> + S2MPU02_LDO22,
>> + S2MPU02_LDO23,
>> + S2MPU02_LDO24,
>> + S2MPU02_LDO25,
>> + S2MPU02_LDO26,
>> + S2MPU02_LDO27,
>> + S2MPU02_LDO28,
>> + S2MPU02_BUCK1,
>> + S2MPU02_BUCK2,
>> + S2MPU02_BUCK3,
>> + S2MPU02_BUCK4,
>> + S2MPU02_BUCK5,
>> + S2MPU02_BUCK6,
>> + S2MPU02_BUCK7,
>> +
>> + S2MPU02_REGULATOR_MAX,
>> +};
>> +
>> +/* Regulator constraints for BUCKx */
>> +#define S2MPU02_BUCK1234_MIN_600MV 600000
>> +#define S2MPU02_BUCK5_MIN_1081_25MV 1081250
>> +#define S2MPU02_BUCK6_MIN_1700MV 1700000
>> +#define S2MPU02_BUCK7_MIN_900MV 900000
>> +
>> +#define S2MPU02_BUCK1234_STEP_6_25MV 6250
>> +#define S2MPU02_BUCK5_STEP_6_25MV 6250
>> +#define S2MPU02_BUCK6_STEP_2_50MV 2500
>> +#define S2MPU02_BUCK7_STEP_6_25MV 6250
>> +
>> +#define S2MPU02_BUCK1234_START_SEL 0x00
>> +#define S2MPU02_BUCK5_START_SEL 0x4D
>> +#define S2MPU02_BUCK6_START_SEL 0x28
>> +#define S2MPU02_BUCK7_START_SEL 0x30
>> +
>> +/*
>> + * Default ramp delay in uv/us. Datasheet says that ramp delay can be
>> + * controlled however it does not specify which register is used for that.
>> + * Let's assume that default value will be set.
>> + */
>
> The comment above applies only to S2MPS14 which does not describe the
> register for setting ramp delay. On S2MPU02 the ramp delay can be set so
> this comment is misleading.
OK. I'll remove this comment.
Thanks for your comment.
Best Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
