On Wed, 9 Mar 2005 22:09:26 +0100, Jens Axboe <[EMAIL PROTECTED]> wrote: > probably not worth the bother, looks like barrier problems. get the > serial console running instead and send the full output, I'll take a > look in the morning.
serial console boot output attached. > > -- > Jens Axboe > > -- Jon Smirl [EMAIL PROTECTED]
Linux version 2.6.11-bk5 ([EMAIL PROTECTED]) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #3 SMP Wed Mar 9 18:36:46 EST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ff74000 (usable) BIOS-e820: 000000003ff74000 - 000000003ff76000 (ACPI NVS) BIOS-e820: 000000003ff76000 - 000000003ff97000 (ACPI data) BIOS-e820: 000000003ff97000 - 0000000040000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved) BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000fe710 DMI 2.3 present. ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000) Built 1 zonelists Kernel command line: ro root=LABEL=/ console=ttyS0 Initializing CPU#0 CPU 0 irqstacks, hard=c03b3000 soft=c03b1000 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 2793.222 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1034896k/1048016k available (1576k kernel code, 12396k reserved, 963k data, 188k init, 130512k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 per-CPU timeslice cutoff: 1462.56 usecs. task migration cache decay timeout: 2 msecs. Booting processor 1/1 eip 3000 CPU 1 irqstacks, hard=c03b4000 soft=c03b2000 Initializing CPU#1 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 Total of 2 processors activated (11091.96 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 pin1=2 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs checking if image is initramfs... it is Freeing initrd memory: 318k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfba5e, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050211 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15) SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Simple Boot Flag value 0x87 read from CMOS RAM was invalid Simple Boot Flag at 0x7a set to 0x1 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1110395018.538:0): initialized highmem bounce pool size: 64 pages Initializing Cryptographic API ACPI: PS/2 Keyboard Controller [KBD] at I/O 0x60, 0x64, irq 1 ACPI: PS/2 Mouse Controller [MOU] at irq 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA hda: IC35L060AVV207-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: DVD-RW IDE1008, ATAPI CD/DVD-ROM drive hdd: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 1024KiB hda: 78125000 sectors (40000 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) mice: PS/2 mouse device common for all mice md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) Starting balanced_irq ACPI wakeup devices: VBTN PCI0 USB0 USB1 USB2 USB3 PCI1 MOU ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 188k freed Red Hat nash version 4.1.18 starting Mounted /proc filesystem md: raid1 personality registered as nr 3 Mounting sysfs md: Autodetecting RAID arrays. Creating /dev SACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169 tarting udev Lomd: autorun ... md: considering hda2 ... md: adding hda2 ... md: created md0 md: bind<hda2> md: running: <hda2> ading libata.ko raid1: raid set md0 active with 1 out of 2 mirrors md: ... autorun DONE. module Loading ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 169 ata_piix.ko moduata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 169 le Loading raidKernel panic - not syncing: Attempted to kill init! 1.ko module Cre ating root devic