I have a brand new Western Digital sata drive, VIA KT600 based ECS
motherboard on which I am trying to install various distros (with installers
based on 2.4.26, 2.6.7, 2.6.8, 2.6.11 etc) all of them fail to detect the HD
(and bomb out) because sata-via is ignoring it . I have only one disk, I am
not interested in raid.
lspci which tells me it is VIA 6420 and should be supported based on
sata-via.c. Following are syslog snippets that show more.
I would appreciate your help in resolving this. Thanks,
Jay
##
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00
[Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
Capabilities: [80] Power Management version 2
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller (rev 80)
Subsystem: Elitegroup Computer Systems: Unknown device 1884
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at b000 [size=8]
I/O ports at b400 [size=4]
I/O ports at b800 [size=8]
I/O ports at bc00 [size=4]
I/O ports at c000 [size=16]
I/O ports at c400 [size=256]
Capabilities: [c0] Power Management version 2
##Dmesg when I connect the disk on channel 1
libata version 1.10 loaded.
sata_via version 1.1
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 11 (level, low) -> IRQ 11
sata_via(0000:00:0f.0): routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0xB000 ctl 0xB402 bmdma 0xC000 irq 11
ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xBC02 bmdma 0xC008 irq 11
ata1: dev 0 cfg 49:3030 82:0078 83:0078 84:0000 85:0000 86:3fff 87:0010
88:000f
ata1: no dma/lba
ata1: dev 0 not supported, ignoring
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
##with disk on second channel following
ata1: no device found (phy stat 00000000)
scsi0 : sata_via
ata2: dev 0 cfg 49:3030 82:0078 83:0078 84:0078 85:0000 86:0000 87:0000
88:0000
ata2: no dma/lba
ata2: dev 0 not supported, ignoring
scsi1 : sata_via
## I took this disk and sata cable on a different (ICH5 based) motherboard and
## knoppix detected the disk ok and associated sda with it.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
