Add device tree binding for Qualcomm AHCI SATA controller and specifically the sata controller on the IPQ806x family of SoCs.
We can utilize the "generic-ahci" platform driver with the addition of the sata phy to enable SATA support on Qualcomm SoCs with AHCI controllers. Signed-off-by: Kumar Gala <[email protected]> --- v5: * Moved to using "generic-ahci" binding support and assigned-clocks so we can use upstream generic ahci support w/o a special driver. Updated binding spec to reflect that. v4: * Added simple PM ops implementation * Added setting of pmalive clk v3: * Added comment about suspend/resume not supported * Fixup ahci_platform_init_host for upstream change to interface * cleanup error handling of rxoob clk, moved to devm_clk_get/put v2: * Fixed MODULE_LICENSE to be GPL v2 .../devicetree/bindings/ata/qcom-sata.txt | 48 ++++++++++++++++++++++ 1 file changed, 48 insertions(+) create mode 100644 Documentation/devicetree/bindings/ata/qcom-sata.txt diff --git a/Documentation/devicetree/bindings/ata/qcom-sata.txt b/Documentation/devicetree/bindings/ata/qcom-sata.txt new file mode 100644 index 0000000..094de91 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/qcom-sata.txt @@ -0,0 +1,48 @@ +* Qualcomm AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, must contain "generic-ahci" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- phys : Must contain exactly one entry as specified + in phy-bindings.txt +- phy-names : Must be "sata-phy" + +Required properties for "qcom,ipq806x-ahci" compatible: +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be: + "slave_iface" - Fabric port AHB clock for SATA + "iface" - AHB clock + "core" - core clock + "rxoob" - RX out-of-band clock + "pmalive" - Power Module Alive clock +- assigned-clocks : Shall be: + SATA_RXOOB_CLK + SATA_PMALIVE_CLK +- assigned-clock-rates : Shall be: + 100Mhz (100000000) for SATA_RXOOB_CLK + 100Mhz (100000000) for SATA_PMALIVE_CLK + +Example: + sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <0 209 0x0>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_iface", "iface", "core", + "rxoob", "pmalive"; + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + }; -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
