rename st-pwm to pwm-regulator. And support getting voltage & duty table from
device tree, other platforms can also use this driver without any modify.

Signed-off-by: Chris Zhong <z...@rock-chips.com>
Reviewed-by: Doug Anderson <diand...@chromium.org>
Tested-by: Doug Anderson <diand...@chromium.org>

---

Changes in v7:
Adviced by Mark Brown
- re-edit changelog

Changes in v6: None
Changes in v4:
Adviced by Doug Anderson
- improve kconfig
- add const for desc structure

Changes in v3:
Adviced by Doug Anderson
- Make Kconfig & Makefile alphabetical
- remove pwm_reg_period from pwm_regulator_data
- modify the calculation in pwm_regulator_set_voltage_sel
- add length validity check

Changes in v2:
Adviced by Lee Jones
- rename the file
- remove all the prefix st_
- add depend on PWM in Kconfig

 drivers/regulator/Kconfig                       |   13 +-
 drivers/regulator/Makefile                      |    2 +-
 drivers/regulator/{st-pwm.c => pwm-regulator.c} |  147 ++++++++++++-----------
 3 files changed, 85 insertions(+), 77 deletions(-)
 rename drivers/regulator/{st-pwm.c => pwm-regulator.c} (44%)

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index fb32bab..b927cab 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -449,6 +449,13 @@ config REGULATOR_PFUZE100
          Say y here to support the regulators found on the Freescale
          PFUZE100/PFUZE200 PMIC.
 
+config REGULATOR_PWM
+       tristate "PWM voltage regulator"
+       depends on PWM
+       help
+         This driver supports PWM controlled voltage regulators. PWM
+         duty cycle can increase or decrease the voltage.
+
 config REGULATOR_RC5T583
        tristate "RICOH RC5T583 Power regulators"
        depends on MFD_RC5T583
@@ -493,12 +500,6 @@ config REGULATOR_S5M8767
         via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
         supports DVS mode with 8bits of output voltage control.
 
-config REGULATOR_ST_PWM
-       tristate "STMicroelectronics PWM voltage regulator"
-       depends on ARCH_STI
-       help
-        This driver supports ST's PWM controlled voltage regulators.
-
 config REGULATOR_TI_ABB
        tristate "TI Adaptive Body Bias on-chip LDO"
        depends on ARCH_OMAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 236fdbb..f3cf5a5 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
 obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
 obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
+obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
 obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
 obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o
 obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
@@ -66,7 +67,6 @@ obj-$(CONFIG_REGULATOR_RK808)   += rk808-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
 obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
-obj-$(CONFIG_REGULATOR_ST_PWM) += st-pwm.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
 obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
diff --git a/drivers/regulator/st-pwm.c b/drivers/regulator/pwm-regulator.c
similarity index 44%
rename from drivers/regulator/st-pwm.c
rename to drivers/regulator/pwm-regulator.c
index 5ea78df..d3f55ea 100644
--- a/drivers/regulator/st-pwm.c
+++ b/drivers/regulator/pwm-regulator.c
@@ -1,5 +1,5 @@
 /*
- * Regulator driver for ST's PWM Regulators
+ * Regulator driver for PWM Regulators
  *
  * Copyright (C) 2014 - STMicroelectronics Inc.
  *
@@ -20,43 +20,40 @@
 #include <linux/of_device.h>
 #include <linux/pwm.h>
 
-#define ST_PWM_REG_PERIOD 8448
-
-struct st_pwm_regulator_pdata {
-       const struct regulator_desc *desc;
-       struct st_pwm_voltages *duty_cycle_table;
-};
-
-struct st_pwm_regulator_data {
-       const struct st_pwm_regulator_pdata *pdata;
+struct pwm_regulator_data {
+       struct regulator_desc desc;
+       struct pwm_voltages *duty_cycle_table;
        struct pwm_device *pwm;
        bool enabled;
        int state;
 };
 
-struct st_pwm_voltages {
+struct pwm_voltages {
        unsigned int uV;
        unsigned int dutycycle;
 };
 
-static int st_pwm_regulator_get_voltage_sel(struct regulator_dev *dev)
+static int pwm_regulator_get_voltage_sel(struct regulator_dev *dev)
 {
-       struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+       struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
 
        return drvdata->state;
 }
 
-static int st_pwm_regulator_set_voltage_sel(struct regulator_dev *dev,
-                                           unsigned selector)
+static int pwm_regulator_set_voltage_sel(struct regulator_dev *dev,
+                                        unsigned selector)
 {
-       struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+       struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+       unsigned int pwm_reg_period;
        int dutycycle;
        int ret;
 
-       dutycycle = (ST_PWM_REG_PERIOD / 100) *
-               drvdata->pdata->duty_cycle_table[selector].dutycycle;
+       pwm_reg_period = pwm_get_period(drvdata->pwm);
 
-       ret = pwm_config(drvdata->pwm, dutycycle, ST_PWM_REG_PERIOD);
+       dutycycle = (pwm_reg_period *
+                   drvdata->duty_cycle_table[selector].dutycycle) / 100;
+
+       ret = pwm_config(drvdata->pwm, dutycycle, pwm_reg_period);
        if (ret) {
                dev_err(&dev->dev, "Failed to configure PWM\n");
                return ret;
@@ -76,61 +73,40 @@ static int st_pwm_regulator_set_voltage_sel(struct 
regulator_dev *dev,
        return 0;
 }
 
-static int st_pwm_regulator_list_voltage(struct regulator_dev *dev,
-                                        unsigned selector)
+static int pwm_regulator_list_voltage(struct regulator_dev *dev,
+                                     unsigned selector)
 {
-       struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+       struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
 
-       if (selector >= dev->desc->n_voltages)
+       if (selector >= drvdata->desc.n_voltages)
                return -EINVAL;
 
-       return drvdata->pdata->duty_cycle_table[selector].uV;
+       return drvdata->duty_cycle_table[selector].uV;
 }
 
-static struct regulator_ops st_pwm_regulator_voltage_ops = {
-       .set_voltage_sel = st_pwm_regulator_set_voltage_sel,
-       .get_voltage_sel = st_pwm_regulator_get_voltage_sel,
-       .list_voltage    = st_pwm_regulator_list_voltage,
+static struct regulator_ops pwm_regulator_voltage_ops = {
+       .set_voltage_sel = pwm_regulator_set_voltage_sel,
+       .get_voltage_sel = pwm_regulator_get_voltage_sel,
+       .list_voltage    = pwm_regulator_list_voltage,
        .map_voltage     = regulator_map_voltage_iterate,
 };
 
-static struct st_pwm_voltages b2105_duty_cycle_table[] = {
-       { .uV = 1114000, .dutycycle = 0,  },
-       { .uV = 1095000, .dutycycle = 10, },
-       { .uV = 1076000, .dutycycle = 20, },
-       { .uV = 1056000, .dutycycle = 30, },
-       { .uV = 1036000, .dutycycle = 40, },
-       { .uV = 1016000, .dutycycle = 50, },
-       /* WARNING: Values above 50% duty-cycle cause boot failures. */
-};
-
-static const struct regulator_desc b2105_desc = {
-       .name           = "b2105-pwm-regulator",
-       .ops            = &st_pwm_regulator_voltage_ops,
+static const struct regulator_desc pwm_regulator_desc = {
+       .name           = "pwm-regulator",
+       .ops            = &pwm_regulator_voltage_ops,
        .type           = REGULATOR_VOLTAGE,
        .owner          = THIS_MODULE,
-       .n_voltages     = ARRAY_SIZE(b2105_duty_cycle_table),
        .supply_name    = "pwm",
 };
 
-static const struct st_pwm_regulator_pdata b2105_info = {
-       .desc             = &b2105_desc,
-       .duty_cycle_table = b2105_duty_cycle_table,
-};
-
-static const struct of_device_id st_pwm_of_match[] = {
-       { .compatible = "st,b2105-pwm-regulator", .data = &b2105_info, },
-       { },
-};
-MODULE_DEVICE_TABLE(of, st_pwm_of_match);
-
-static int st_pwm_regulator_probe(struct platform_device *pdev)
+static int pwm_regulator_probe(struct platform_device *pdev)
 {
-       struct st_pwm_regulator_data *drvdata;
+       struct pwm_regulator_data *drvdata;
+       struct property *prop;
        struct regulator_dev *regulator;
        struct regulator_config config = { };
        struct device_node *np = pdev->dev.of_node;
-       const struct of_device_id *of_match;
+       int length, ret;
 
        if (!np) {
                dev_err(&pdev->dev, "Device Tree node missing\n");
@@ -141,12 +117,37 @@ static int st_pwm_regulator_probe(struct platform_device 
*pdev)
        if (!drvdata)
                return -ENOMEM;
 
-       of_match = of_match_device(st_pwm_of_match, &pdev->dev);
-       if (!of_match) {
-               dev_err(&pdev->dev, "failed to match of device\n");
-               return -ENODEV;
+       memcpy(&drvdata->desc, &pwm_regulator_desc, sizeof(pwm_regulator_desc));
+
+       /* determine the number of voltage-table */
+       prop = of_find_property(np, "voltage-table", &length);
+       if (!prop) {
+               dev_err(&pdev->dev, "No voltage-table\n");
+               return -EINVAL;
+       }
+
+       if ((length < sizeof(*drvdata->duty_cycle_table)) ||
+           (length % sizeof(*drvdata->duty_cycle_table))) {
+               dev_err(&pdev->dev, "voltage-table length(%d) is invalid\n",
+                       length);
+               return -EINVAL;
+       }
+
+       drvdata->desc.n_voltages = length / sizeof(*drvdata->duty_cycle_table);
+
+       drvdata->duty_cycle_table = devm_kzalloc(&pdev->dev,
+                                                length, GFP_KERNEL);
+       if (!drvdata->duty_cycle_table)
+               return -ENOMEM;
+
+       /* read voltage table from DT property */
+       ret = of_property_read_u32_array(np, "voltage-table",
+                                        (u32 *)drvdata->duty_cycle_table,
+                                        length / sizeof(u32));
+       if (ret < 0) {
+               dev_err(&pdev->dev, "read voltage-table failed\n");
+               return ret;
        }
-       drvdata->pdata = of_match->data;
 
        config.init_data = of_get_regulator_init_data(&pdev->dev, np);
        if (!config.init_data)
@@ -163,28 +164,34 @@ static int st_pwm_regulator_probe(struct platform_device 
*pdev)
        }
 
        regulator = devm_regulator_register(&pdev->dev,
-                                           drvdata->pdata->desc, &config);
+                                           &drvdata->desc, &config);
        if (IS_ERR(regulator)) {
                dev_err(&pdev->dev, "Failed to register regulator %s\n",
-                       drvdata->pdata->desc->name);
+                       drvdata->desc.name);
                return PTR_ERR(regulator);
        }
 
        return 0;
 }
 
-static struct platform_driver st_pwm_regulator_driver = {
+static const struct of_device_id pwm_of_match[] = {
+       { .compatible = "pwm-regulator" },
+       { },
+};
+MODULE_DEVICE_TABLE(of, pwm_of_match);
+
+static struct platform_driver pwm_regulator_driver = {
        .driver = {
-               .name           = "st-pwm-regulator",
+               .name           = "pwm-regulator",
                .owner          = THIS_MODULE,
-               .of_match_table = of_match_ptr(st_pwm_of_match),
+               .of_match_table = of_match_ptr(pwm_of_match),
        },
-       .probe = st_pwm_regulator_probe,
+       .probe = pwm_regulator_probe,
 };
 
-module_platform_driver(st_pwm_regulator_driver);
+module_platform_driver(pwm_regulator_driver);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Lee Jones <lee.jo...@linaro.org>");
-MODULE_DESCRIPTION("ST PWM Regulator Driver");
-MODULE_ALIAS("platform:st_pwm-regulator");
+MODULE_DESCRIPTION("PWM Regulator Driver");
+MODULE_ALIAS("platform:pwm-regulator");
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Reply via email to