My mistake, I will fix it, many thanks. Best Regards, Jingchang
>-----Original Message----- >From: Joseph Lo [mailto:jose...@nvidia.com] >Sent: Monday, October 13, 2014 5:41 PM >To: Lu Jingchang-B35083; gre...@linuxfoundation.org >Cc: devicet...@vger.kernel.org; pe...@hurleysoftware.com; a...@arndb.de; >linux-kernel@vger.kernel.org; linux-ser...@vger.kernel.org; linux-arm- >ker...@lists.infradead.org >Subject: Re: [PATCHv2] serial: of-serial: fix up PM ops on >no_console_suspend and port type > >Hi, > >On 10/13/2014 03:37 PM, Jingchang Lu wrote: >> This patch fixes commit 2dea53bf57783f243c892e99c10c6921e956aa7e, >> "serial: of-serial: add PM suspend/resume support", which disables >> the uart clock on suspend, but also causes a hardware hang on register >> access if no_console_suspend command line option is used. >> >> Also, not every of_serial device is an 8250 port, so the serial8250 >> suspend/resume functions should only be applied to a real 8250 port. >> >> Signed-off-by: Jingchang Lu <jingchang...@freescale.com> >> --- >> changes in v2: >> add switch selection on uart type. > >After apply this, it can't build for me. I still need to apply the fix >like something below. > >diff --git a/drivers/tty/serial/of_serial.c >b/drivers/tty/serial/of_serial.c >index e535f9c1563d..14c1ff4e7816 100644 >--- a/drivers/tty/serial/of_serial.c >+++ b/drivers/tty/serial/of_serial.c >@@ -9,6 +9,7 @@ > * 2 of the License, or (at your option) any later version. > * > */ >+#include <linux/console.h> > #include <linux/module.h> > #include <linux/slab.h> > #include <linux/delay.h> >@@ -248,13 +249,13 @@ static int of_serial_suspend(struct device *dev) > #ifdef CONFIG_SERIAL_8250 > case PORT_8250 ... PORT_MAX_8250: > { >- struct uart_8250_port port8250; >+ struct uart_8250_port *port8250; > port8250 = serial8250_get_port(info->line); > > serial8250_suspend_port(info->line); > if (info->clk && >- (!uart_console(port8250) || >- (uart_console(port8250) && console_suspend_enabled))) >+ (!uart_console(&port8250->port) || >+ (uart_console(&port8250->port) && >console_suspend_enabled))) > clk_disable_unprepare(info->clk); > break; > } >@@ -274,12 +275,12 @@ static int of_serial_resume(struct device *dev) > #ifdef CONFIG_SERIAL_8250 > case PORT_8250 ... PORT_MAX_8250: > { >- struct uart_8250_port port8250; >+ struct uart_8250_port *port8250; > port8250 = serial8250_get_port(info->line); > > if (info->clk && >- (!uart_console(port8250) || >- (uart_console(port8250) && console_suspend_enabled))) >+ (!uart_console(&port8250->port) || >+ (uart_console(&port8250->port) && >console_suspend_enabled))) > clk_prepare_enable(info->clk); > > serial8250_resume_port(info->line); > >-Joseph > >> >> drivers/tty/serial/of_serial.c | 42 >++++++++++++++++++++++++++++++++++++------ >> 1 file changed, 36 insertions(+), 6 deletions(-) >> >> diff --git a/drivers/tty/serial/of_serial.c >b/drivers/tty/serial/of_serial.c >> index 8bc2563..b525383 100644 >> --- a/drivers/tty/serial/of_serial.c >> +++ b/drivers/tty/serial/of_serial.c >> @@ -245,9 +245,24 @@ static int of_serial_suspend(struct device *dev) >> { >> struct of_serial_info *info = dev_get_drvdata(dev); >> >> - serial8250_suspend_port(info->line); >> - if (info->clk) >> - clk_disable_unprepare(info->clk); >> + switch(info->type) { >> +#ifdef CONFIG_SERIAL_8250 >> + case PORT_8250 ... PORT_MAX_8250: >> + { >> + struct uart_8250_port port8250; >> + port8250 = serial8250_get_port(info->line); >> + >> + serial8250_suspend_port(info->line); >> + if (info->clk && >> + (!uart_console(port8250) || >> + (uart_console(port8250) && console_suspend_enabled))) >> + clk_disable_unprepare(info->clk); >> + break; >> + } >> +#endif >> + default: >> + break; >> + } >> >> return 0; >> } >> @@ -256,10 +271,25 @@ static int of_serial_resume(struct device *dev) >> { >> struct of_serial_info *info = dev_get_drvdata(dev); >> >> - if (info->clk) >> - clk_prepare_enable(info->clk); >> + switch(info->type) { >> +#ifdef CONFIG_SERIAL_8250 >> + case PORT_8250 ... PORT_MAX_8250: >> + { >> + struct uart_8250_port port8250; >> + port8250 = serial8250_get_port(info->line); >> + >> + if (info->clk && >> + (!uart_console(port8250) || >> + (uart_console(port8250) && console_suspend_enabled))) >> + clk_prepare_enable(info->clk); >> >> - serial8250_resume_port(info->line); >> + serial8250_resume_port(info->line); >> + break; >> + } >> +#endif >> + default: >> + break; >> + } >> >> return 0; >> } >>
