The file of-serial.txt was only for 8250 compatible UART implementations,
so renamed it to 8250.txt to avoid confusing other persons.
Signed-off-by: Chunyan Zhang <chunyan.zh...@spreadtrum.com>
---
Documentation/devicetree/bindings/serial/8250.txt | 50 ++++++++++++++++++++
.../devicetree/bindings/serial/of-serial.txt | 50 --------------------
2 files changed, 50 insertions(+), 50 deletions(-)
create mode 100644 Documentation/devicetree/bindings/serial/8250.txt
delete mode 100644 Documentation/devicetree/bindings/serial/of-serial.txt
diff --git a/Documentation/devicetree/bindings/serial/8250.txt
b/Documentation/devicetree/bindings/serial/8250.txt
new file mode 100644
index 0000000..7705477
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/8250.txt
@@ -0,0 +1,50 @@
+* UART (Universal Asynchronous Receiver/Transmitter)
+
+Required properties:
+- compatible : one of:
+ - "ns8250"
+ - "ns16450"
+ - "ns16550a"
+ - "ns16550"
+ - "ns16750"
+ - "ns16850"
+ - "nvidia,tegra20-uart"
+ - "nxp,lpc3220-uart"
+ - "ibm,qpace-nwp-serial"
+ - "altr,16550-FIFO32"
+ - "altr,16550-FIFO64"
+ - "altr,16550-FIFO128"
+ - "serial" if the port type is unknown.
+- reg : offset and length of the register set for the device.
+- interrupts : should contain uart interrupt.
+- clock-frequency : the input clock frequency for the UART
+ or
+ clocks phandle to refer to the clk used as per Documentation/devicetree
+ /bindings/clock/clock-bindings.txt
+
+Optional properties:
+- current-speed : the current active speed of the UART.
+- reg-offset : offset to apply to the mapbase from the start of the registers.
+- reg-shift : quantity to shift the register offsets by.
+- reg-io-width : the size (in bytes) of the IO accesses that should be
+ performed on the device. There are some systems that require 32-bit
+ accesses to the UART (e.g. TI davinci).
+- used-by-rtas : set to indicate that the port is in use by the OpenFirmware
+ RTAS and should not be registered.
+- no-loopback-test: set to indicate that the port does not implements loopback
+ test mode
+- fifo-size: the fifo size of the UART.
+- auto-flow-control: one way to enable automatic flow control support. The
+ driver is allowed to detect support for the capability even without this
+ property.
+- has-hw-flow-control: the hardware has flow control capability.
+
+Example:
+
+ uart@80230000 {
+ compatible = "ns8250";
+ reg = <0x80230000 0x100>;
+ clock-frequency = <3686400>;
+ interrupts = <10>;
+ reg-shift = <2>;
+ };
diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt
b/Documentation/devicetree/bindings/serial/of-serial.txt
deleted file mode 100644
index 7705477..0000000
--- a/Documentation/devicetree/bindings/serial/of-serial.txt
+++ /dev/null
@@ -1,50 +0,0 @@
-* UART (Universal Asynchronous Receiver/Transmitter)
-
-Required properties:
-- compatible : one of:
- - "ns8250"
- - "ns16450"
- - "ns16550a"
- - "ns16550"
- - "ns16750"
- - "ns16850"
- - "nvidia,tegra20-uart"
- - "nxp,lpc3220-uart"
- - "ibm,qpace-nwp-serial"
- - "altr,16550-FIFO32"
- - "altr,16550-FIFO64"
- - "altr,16550-FIFO128"
- - "serial" if the port type is unknown.
-- reg : offset and length of the register set for the device.
-- interrupts : should contain uart interrupt.
-- clock-frequency : the input clock frequency for the UART
- or
- clocks phandle to refer to the clk used as per Documentation/devicetree
- /bindings/clock/clock-bindings.txt
-
-Optional properties:
-- current-speed : the current active speed of the UART.
-- reg-offset : offset to apply to the mapbase from the start of the registers.
-- reg-shift : quantity to shift the register offsets by.
-- reg-io-width : the size (in bytes) of the IO accesses that should be
- performed on the device. There are some systems that require 32-bit
- accesses to the UART (e.g. TI davinci).
-- used-by-rtas : set to indicate that the port is in use by the OpenFirmware
- RTAS and should not be registered.
-- no-loopback-test: set to indicate that the port does not implements loopback
- test mode
-- fifo-size: the fifo size of the UART.
-- auto-flow-control: one way to enable automatic flow control support. The
- driver is allowed to detect support for the capability even without this
- property.
-- has-hw-flow-control: the hardware has flow control capability.
-
-Example:
-
- uart@80230000 {
- compatible = "ns8250";
- reg = <0x80230000 0x100>;
- clock-frequency = <3686400>;
- interrupts = <10>;
- reg-shift = <2>;
- };
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
