On 12/21/2014 01:20 AM, Pali Rohár wrote:
This patch adds new function i8k_get_fan_nominal_speed() for doing SMM call
which will return nominal fan RPM for specified fan speed. It returns nominal
RPM value at which fan operate when speed (0, 1, 2, 3) is set. It looks like
RPM value is not accurate, but still provides very useful information.
First it can be used to validate if certain fan speed could be accepted by SMM
for setting fan speed and we can use this routine to detect maximal fan speed.
Second it returns RPM value, so we can check if value looks correct with
multiplier 30 or multiplier 1 (until now only these two multiplier were used).
If RPM value with multiplier 30 is too high, then multiplier 1 is used.
In case when SMM reports that new function is not supported we will fallback
to old hardcoded values. Maximal fan speed would be 2 and RPM multiplier 30.
Signed-off-by: Pali Rohár <pali.ro...@gmail.com>
Tested-by: Pali Rohár <pali.ro...@gmail.com>
---
drivers/char/i8k.c | 89 ++++++++++++++++++++++++++++++++++++++++++++--------
1 file changed, 76 insertions(+), 13 deletions(-)
diff --git a/drivers/char/i8k.c b/drivers/char/i8k.c
index 48d701c..ce2147c 100644
--- a/drivers/char/i8k.c
+++ b/drivers/char/i8k.c
@@ -6,6 +6,7 @@
* Hwmon integration:
* Copyright (C) 2011 Jean Delvare <jdelv...@suse.de>
* Copyright (C) 2013, 2014 Guenter Roeck <li...@roeck-us.net>
+ * Copyright (C) 2014 Pali Rohár <pali.ro...@gmail.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -42,12 +43,13 @@
#define I8K_SMM_SET_FAN 0x01a3
#define I8K_SMM_GET_FAN 0x00a3
#define I8K_SMM_GET_SPEED 0x02a3
+#define I8K_SMM_GET_NOM_SPEED 0x04a3
#define I8K_SMM_GET_TEMP 0x10a3
#define I8K_SMM_GET_TEMP_TYPE 0x11a3
#define I8K_SMM_GET_DELL_SIG1 0xfea3
#define I8K_SMM_GET_DELL_SIG2 0xffa3
-#define I8K_FAN_MULT 30
+#define I8K_FAN_MAX_RPM 30000
#define I8K_MAX_TEMP 127
#define I8K_FN_NONE 0x00
@@ -64,7 +66,7 @@ static DEFINE_MUTEX(i8k_mutex);
static char bios_version[4];
static struct device *i8k_hwmon_dev;
static u32 i8k_hwmon_flags;
-static int i8k_fan_mult;
+static int i8k_fan_mult = 30;
Why did you drop I8K_FAN_MULT ?
static int i8k_pwm_mult;
static int i8k_fan_max = I8K_FAN_HIGH;
@@ -95,13 +97,13 @@ static bool power_status;
module_param(power_status, bool, 0600);
MODULE_PARM_DESC(power_status, "Report power status in /proc/i8k");
-static int fan_mult = I8K_FAN_MULT;
+static int fan_mult;
module_param(fan_mult, int, 0);
-MODULE_PARM_DESC(fan_mult, "Factor to multiply fan speed with");
+MODULE_PARM_DESC(fan_mult, "Factor to multiply fan speed with (default:
autodetect)");
-static int fan_max = I8K_FAN_HIGH;
+static int fan_max;
module_param(fan_max, int, 0);
-MODULE_PARM_DESC(fan_max, "Maximum configurable fan speed");
+MODULE_PARM_DESC(fan_max, "Maximum configurable fan speed (default:
autodetect)");
static int i8k_open_fs(struct inode *inode, struct file *file);
static long i8k_ioctl(struct file *, unsigned int, unsigned long);
@@ -276,6 +278,17 @@ static int i8k_get_fan_speed(int fan)
}
/*
+ * Read the fan nominal rpm for specific fan speed.
+ */
+static int i8k_get_fan_nominal_speed(int fan, int speed)
+{
+ struct smm_regs regs = { .eax = I8K_SMM_GET_NOM_SPEED, };
+
+ regs.ebx = (fan & 0xff) | (speed << 8);
+ return i8k_smm(®s) ? : (regs.eax & 0xffff) * i8k_fan_mult;
+}
+
+/*
* Set the fan speed (off, low, high). Returns the new fan status.
*/
static int i8k_set_fan(int fan, int speed)
@@ -854,7 +867,9 @@ MODULE_DEVICE_TABLE(dmi, i8k_dmi_table);
*/
static int __init i8k_probe(void)
{
+ const struct i8k_config_data *conf;
Why did you move this variable declaration ?
const struct dmi_system_id *id;
+ int fan, val, ret;
/*
* Get DMI information
@@ -883,19 +898,67 @@ static int __init i8k_probe(void)
return -ENODEV;
}
- i8k_fan_mult = fan_mult;
- i8k_fan_max = fan_max ? : I8K_FAN_HIGH; /* Must not be 0 */
+ /*
+ * Autodetect fan multiplier and maximal fan speed from dmi config
+ * Values specified in module parameters override values from dmi
+ */
id = dmi_first_match(i8k_dmi_table);
if (id && id->driver_data) {
- const struct i8k_config_data *conf = id->driver_data;
+ conf = id->driver_data;
+ if (fan_mult <= 0 && conf->fan_mult > 0)
I still don't see the value in accepting fan_mult < 0 (compeared to == 0).
+ fan_mult = conf->fan_mult;
+ if (fan_max <= 0 && conf->fan_max > 0)
Same for fan_max < 0.
+ fan_max = conf->fan_max;
+ }
- if (fan_mult == I8K_FAN_MULT && conf->fan_mult)
- i8k_fan_mult = conf->fan_mult;
- if (fan_max == I8K_FAN_HIGH && conf->fan_max)
- i8k_fan_max = conf->fan_max;
+ if (fan_max <= 0) {
Same here.
+ /*
+ * Autodetect maximal fan speed value
+ * Speed value is valid if i8k_get_fan_nominal_speed() not fail
+ */
+ for (fan = 0; fan < 2; ++fan) {
+ for (val = 1; val < 256; ++val) {
+ if (i8k_get_fan_nominal_speed(fan, val) < 0)
+ break;
+ fan_max = val; /* Must not be 0 */
+ }
+ if (fan_max != 0) {
+ i8k_fan_max = fan_max;
+ break;
+ }
+ }
+ } else {
+ /* Maximal fan speed was specified in module param or in dmi */
+ i8k_fan_max = fan_max;
}
+
i8k_pwm_mult = DIV_ROUND_UP(255, i8k_fan_max);
+ if (fan_mult <= 0) {
Same here.
Thanks,
Guenter
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/