On Thu, Feb 12, 2015 at 3:03 PM, Marek Belisko <ma...@goldelico.com> wrote:
> From: "H. Nikolaus Schaller" <h...@goldelico.com>
>
> Signed-off-by: H. Nikolaus Schaller <h...@goldelico.com>
> ---
> arch/arm/boot/dts/omap3-pandora-1ghz.dts | 65
> ++++++++++++++++++++++++++++++++
> 1 file changed, 65 insertions(+)
> create mode 100644 arch/arm/boot/dts/omap3-pandora-1ghz.dts
>
> diff --git a/arch/arm/boot/dts/omap3-pandora-1ghz.dts
> b/arch/arm/boot/dts/omap3-pandora-1ghz.dts
> new file mode 100644
> index 0000000..6286f41
> --- /dev/null
> +++ b/arch/arm/boot/dts/omap3-pandora-1ghz.dts
...
> +
> + control_pins: pinmux_control_pins {
> + pinctrl-single,pins = <
> + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN |
> MUX_MODE4) /* etk_d0.gpio_14 = HP_SHUTDOWN */
> + OMAP3630_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4)
> /* etk_d1.gpio_15 = BT_SHUTDOWN */
> + OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)
> /* etk_d2.gpio_16 = RESET_USB_HOST */
> + OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT_PULLUP |
> MUX_MODE4) /* etk_d7.gpio_21 = WIFI IRQ */
The WG7210 document claims that no pulldown/pullup is needed, and we
always had it disabled. The mainline wl1251 driver also reconfigures
that signal to be active high on wl1251 side, and uses rising edge
interrupts (I don't know why it does that).
> + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
> /* etk_d8.gpio_22 = MSECURE */
> + OMAP3630_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4)
> /* etk_d9.gpio_23 = WIFI_POWER */
I think we also need these here:
OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT | MUX_MODE4) /*
reserved.gpio_127 = MMC2_WP */
OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4) /*
reserved.gpio_126 = MMC1_WP */
OMAP3_WKUP_IOPAD(0x2a58, PIN_OUTPUT | MUX_MODE4) /*
reserved.gpio_128 = LED_MMC1 */
OMAP3_WKUP_IOPAD(0x2a5a, PIN_OUTPUT | MUX_MODE4) /*
reserved.gpio_129 = LED_MMC2 */
GraÅžvydas
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
