Dear, Doug.

Looks good to me. Thanks!

Acked-by: Jaehoon Chung <jh80.ch...@samsung.com>

Best Regards,
Jaehoon Chung

On 02/21/2015 03:57 AM, Doug Anderson wrote:
> We should give dw_mmc a good reset after we apply power.  On some
> boards vqmmc may actually be connected to the IP block in the SoC so
> it's good to reset after power comes in.
> 
> Without this we sometimes see failures enumerating cards on rk3288.
> 
> Signed-off-by: Doug Anderson <diand...@chromium.org>
> ---
>  drivers/mmc/host/dw_mmc.c | 27 ++++++++++++++++++---------
>  1 file changed, 18 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 43fcae1..6a712ae 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -1119,13 +1119,23 @@ static void dw_mci_set_ios(struct mmc_host *mmc, 
> struct mmc_ios *ios)
>               mci_writel(slot->host, PWREN, regs);
>               break;
>       case MMC_POWER_ON:
> -             if (!IS_ERR(mmc->supply.vqmmc) && !slot->host->vqmmc_enabled) {
> -                     ret = regulator_enable(mmc->supply.vqmmc);
> -                     if (ret < 0)
> -                             dev_err(slot->host->dev,
> -                                     "failed to enable vqmmc regulator\n");
> -                     else
> +             if (!slot->host->vqmmc_enabled) {
> +                     if (!IS_ERR(mmc->supply.vqmmc)) {
> +                             ret = regulator_enable(mmc->supply.vqmmc);
> +                             if (ret < 0)
> +                                     dev_err(slot->host->dev,
> +                                             "failed to enable vqmmc\n");
> +                             else
> +                                     slot->host->vqmmc_enabled = true;
> +
> +                     } else {
> +                             /* Keep track so we don't reset again */
>                               slot->host->vqmmc_enabled = true;
> +                     }
> +
> +                     /* Reset our state machine after powering on */
> +                     dw_mci_ctrl_reset(slot->host,
> +                                       SDMMC_CTRL_ALL_RESET_FLAGS);
>               }
>  
>               /* Adjust clock / bus width after power is up */
> @@ -1139,10 +1149,9 @@ static void dw_mci_set_ios(struct mmc_host *mmc, 
> struct mmc_ios *ios)
>               if (!IS_ERR(mmc->supply.vmmc))
>                       mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
>  
> -             if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled) {
> +             if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled)
>                       regulator_disable(mmc->supply.vqmmc);
> -                     slot->host->vqmmc_enabled = false;
> -             }
> +             slot->host->vqmmc_enabled = false;
>  
>               regs = mci_readl(slot->host, PWREN);
>               regs &= ~(1 << slot->id);
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Reply via email to