I run this command and I obtained:
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y080L0
Serial Number: Y23TZR2C
Firmware Version: YAR41BW0
User Capacity: 81,964,302,336 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri Jul 22 11:46:20 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always
- 323
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always
- 3
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always
- 1
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline
- 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
8 Seek_Time_Performance 0x0027 251 245 187 Pre-fail Always
- 37971
9 Power_On_Minutes 0x0032 253 253 000 Old_age Always
- 95h+25m
10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always
- 9
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
- 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
- 38
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
- 949
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline
- 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline
- 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x0008 183 174 000 Old_age Offline
- 30
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 233 000 Old_age Always
- 75
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
- 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 252 252 000 Old_age Always
- 0
208 Spin_Buzz 0x002a 252 252 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 196 196 000 Old_age Offline
- 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
SMART Error Log Version: 1
Warning: ATA error count 46 inconsistent with error log pointer 5
ATA Error Count: 46 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 46 occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 c1 80 c9 2c e3 Error: ICRC, ABRT at LBA = 0x032cc980 = 53266816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 00 41 c9 2c e3 08 00:37:40.848 WRITE DMA
ca 00 00 41 c8 2c e3 08 00:37:40.832 WRITE DMA
ca 00 08 29 39 43 e3 08 00:37:40.832 WRITE DMA
ca 00 08 d9 33 43 e3 08 00:37:40.832 WRITE DMA
ca 00 08 c9 33 43 e3 08 00:37:40.832 WRITE DMA
Error 45 occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 39 8d 2c e3 Error: ICRC, ABRT at LBA = 0x032c8d39 = 53251385
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 00 39 8d 2c e3 08 00:33:07.648 WRITE DMA
ca 00 00 39 8c 2c e3 08 00:33:07.648 WRITE DMA
c8 00 80 80 30 c9 e6 08 00:33:07.632 READ DMA
ca 00 18 89 bf 40 e3 08 00:33:07.632 WRITE DMA
ca 00 60 21 bf 40 e3 08 00:33:07.632 WRITE DMA
Error 44 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 b8 39 b9 2c e3 08 2d+06:26:20.352 WRITE DMA
ca 00 b8 39 b9 2c e3 08 2d+06:26:20.288 WRITE DMA
10 00 ff 00 00 00 e0 08 2d+06:26:20.272 RECALIBRATE [OBS-4]
ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA
ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA
Error 43 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 b8 39 b9 2c e3 08 2d+06:26:20.288 WRITE DMA
10 00 ff 00 00 00 e0 08 2d+06:26:20.272 RECALIBRATE [OBS-4]
ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA
ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA
ca 00 10 81 a6 31 e3 08 2d+06:26:19.952 WRITE DMA
Error 42 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA
ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA
ca 00 10 81 a6 31 e3 08 2d+06:26:19.952 WRITE DMA
ca 00 08 91 a5 31 e3 08 2d+06:26:19.952 WRITE DMA
ca 00 10 b1 a3 31 e3 08 2d+06:26:19.952 WRITE DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
thanks
>-- Messaggio Originale --
>Date: Fri, 22 Jul 2005 11:34:55 +0200 (MEST)
>From: Jan Engelhardt <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>cc: linux-kernel@vger.kernel.org
>Subject: Re: DriveStatusError BadCRC
>
>
>>I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving
this
>>message:
>>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
>>hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
>>ide: failed opcode was: unknown
>>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
>>hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
>>ide: failed opcode was: unknown
>
>Does this happen on boot?
>
>Check your harddrive... smartctl -data -a /dev/hda and look for
>199 UDMA_CRC_Error_Count 0x0008 198 193 000 Old_age Offline
> -
>and
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> c8 00 38 2f 8f 07 e4 08 43d+13:12:02.304 READ DMA
>
>
>
>Jan Engelhardt
>--
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel"
in
>the body of a message to [EMAIL PROTECTED]
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
__________________________________________________________________
TISCALI ADSL 1.25 MEGA
Solo con Tiscali Adsl navighi senza limiti e telefoni senza canone Telecom
a partire da 19,95 Euro/mese.
Attivala entro il 28 luglio, il primo MESE รจ GRATIS! CLICCA QUI.
http://abbonati.tiscali.it/adsl/sa/1e25flat_tc/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
