On 05/20/2015 11:03 AM, Antoine Tenart wrote:
> Ezequiel,
>
> On Sat, May 16, 2015 at 07:02:45PM -0300, Ezequiel Garcia wrote:
>> On 05/11/2015 11:58 AM, Antoine Tenart wrote:
>
>>> -
>>> ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
>>> ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
>>> - ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0;
>>> - ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0;
>>> - ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0;
>>> - ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0;
>>> + ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0;
>>> + ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0;
>>
>> By the time you call this, there's no detected flash, so there's
>> no geometry information such as mtd->writesize, chip->page_shift, etc.
>
> I'll move this to pxa3xx_nand_init_timings().
>
Well, please don't call it init_timings() if you are doing more than
timings setup.
>>> @@ -1577,64 +1558,20 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
>>> return ret;
>>> }
>>>
>>> - chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0);
>>> - id = *((uint16_t *)(info->data_buff));
>>> - if (id != 0)
>>> - dev_info(&info->pdev->dev, "Detect a flash id %x\n", id);
>>> - else {
>>> - dev_warn(&info->pdev->dev,
>>> - "Read out ID 0, potential timing set wrong!!\n");
>>> -
>>> - return -EINVAL;
>>> - }
>>> -
>>> - num = ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1;
>>> - for (i = 0; i < num; i++) {
>>> - if (i < pdata->num_flash)
>>> - f = pdata->flash + i;
>>> - else
>>> - f = &builtin_flash_types[i - pdata->num_flash + 1];
>>> -
>>> - /* find the chip in default list */
>>> - if (f->chip_id == id)
>>> - break;
>>> - }
>>> -
>>> - if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) {
>>> - dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n");
>>> -
>>> - return -EINVAL;
>>> - }
>>> -
>>> - ret = pxa3xx_nand_config_flash(info, f);
>>
>> This second call to pxa3xx_nand_config_flash was in charge of re-configuring
>> the device after proper identification.
>>
>> I'd say a proper approach is to configure default parameters,
>> call nand_scan_ident, and finally re-configure using the detected values.
>
> That's what is done already, default parameters are setup in
> pxa3xx_nand_sensing(), using onfi_async_timing_mode_to_sdr_timings(0).
> Then once the device is recognized, the proper timings are used by
> calling pxa3xx_nand_init_timings().
>
> Did I miss something here?
>
I'm not talking about the timings but about ndcr configuration. You can
only do that once the device is detected, not before.
The timing stuff look OK.
--
Ezequiel Garcia, VanguardiaSur
www.vanguardiasur.com.ar
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
