I think it is OK. The external interrupt can be edged. And it works well in my
board.
Tony Li
-----Original Message-----
From: Gala Kumar K.-galak
Sent: Tuesday, August 30, 2005 1:43 AM
To: Li Tony-r64360
Cc: linuxppc-embedded; linux-kernel@vger.kernel.org; Gala Kumar K.-galak; Chu
hanjin-r52514
Subject: Re: [PATCH] ppc32 :Added PCI support for MPC83xx
I noticed that you aren't updating the senses array in mpc834x_sys_init_IRQ for
the PCI interrupt lines, is this correct?
Should they not be IRQ_SENSE_LEVEL?
Also, I've done a bit of cosmetic cleanup to the patch, take a look and let me
know if it works. Once we close on the IRQ sense issue I will send this
upstream.
- kumar
---
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -713,6 +713,12 @@ config MPC834x_SYS
help
This option enables support for the MPC 834x SYS evaluation board.
+ Be aware that PCI buses can only function when SYS board is plugged on
+ PIB (Platform IO Board) board from Freescale which provide 3 PCI
slots.
+ Just like PC,the board level initalization is bootloader`s
responsiblilty.
+ The PCI deponds on bootloader configurate board corretly. Refer to
Freescale
+ to get more information about this.
+
endchoice
config PQ2ADS
@@ -1193,6 +1199,11 @@ config PCI
config PCI_DOMAINS
bool
default PCI
+
+config MPC83xx_PCI2
+ bool " Supprt for 2nd PCI host controller"
+ depends on PCI && MPC834x
+ default y if MPC834x_SYS
config PCI_QSPAN
bool "QSpan PCI"
diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.c
b/arch/ppc/platforms/83xx/mpc834x_sys.c
--- a/arch/ppc/platforms/83xx/mpc834x_sys.c
+++ b/arch/ppc/platforms/83xx/mpc834x_sys.c
@@ -62,9 +62,29 @@ extern unsigned long total_memory; /* in
unsigned char __res[sizeof (bd_t)];
#ifdef CONFIG_PCI
-#error "PCI is not supported"
-/* NEED mpc83xx_map_irq & mpc83xx_exclude_device
- see platforms/85xx/mpc85xx_ads_common.c */
+int
+mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char
+pin) {
+ static char pci_irq_table[][4] =
+ /*
+ * PCI IDSEL/INTPIN->INTLINE
+ * A B C D
+ */
+ {
+ {PIRQA, PIRQB, PIRQC, PIRQD}, /* idsel 0x11 */
+ {PIRQC, PIRQD, PIRQA, PIRQB}, /* idsel 0x12 */
+ {PIRQD, PIRQA, PIRQB, PIRQC} /* idsel 0x13 */
+ };
+
+ const long min_idsel = 0x11, max_idsel = 0x13, irqs_per_slot = 4;
+ return PCI_IRQ_TABLE_LOOKUP;
+}
+
+int
+mpc83xx_exclude_device(u_char bus, u_char devfn) {
+ return PCIBIOS_SUCCESSFUL;
+}
#endif /* CONFIG_PCI */
/* ************************************************************************
@@ -88,7 +108,7 @@ mpc834x_sys_setup_arch(void)
#ifdef CONFIG_PCI
/* setup PCI host bridges */
- mpc83xx_sys_setup_hose();
+ mpc83xx_setup_hose();
#endif
mpc83xx_early_serial_map();
diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.h
b/arch/ppc/platforms/83xx/mpc834x_sys.h
--- a/arch/ppc/platforms/83xx/mpc834x_sys.h
+++ b/arch/ppc/platforms/83xx/mpc834x_sys.h
@@ -26,7 +26,7 @@
#define VIRT_IMMRBAR ((uint)0xfe000000)
#define BCSR_PHYS_ADDR ((uint)0xf8000000)
-#define BCSR_SIZE ((uint)(32 * 1024))
+#define BCSR_SIZE ((uint)(128 * 1024))
#define BCSR_MISC_REG2_OFF 0x07
#define BCSR_MISC_REG2_PORESET 0x01
@@ -34,23 +34,25 @@
#define BCSR_MISC_REG3_OFF 0x08
#define BCSR_MISC_REG3_CNFLOCK 0x80
-#ifdef CONFIG_PCI
-/* PCI interrupt controller */
-#define PIRQA MPC83xx_IRQ_IRQ4
-#define PIRQB MPC83xx_IRQ_IRQ5
-#define PIRQC MPC83xx_IRQ_IRQ6
-#define PIRQD MPC83xx_IRQ_IRQ7
-
-#define MPC834x_SYS_PCI1_LOWER_IO 0x00000000
-#define MPC834x_SYS_PCI1_UPPER_IO 0x00ffffff
-
-#define MPC834x_SYS_PCI1_LOWER_MEM 0x80000000
-#define MPC834x_SYS_PCI1_UPPER_MEM 0x9fffffff
-
-#define MPC834x_SYS_PCI1_IO_BASE 0xe2000000
-#define MPC834x_SYS_PCI1_MEM_OFFSET 0x00000000
-
-#define MPC834x_SYS_PCI1_IO_SIZE 0x01000000
-#endif /* CONFIG_PCI */
+#define PIRQA MPC83xx_IRQ_EXT4
+#define PIRQB MPC83xx_IRQ_EXT5
+#define PIRQC MPC83xx_IRQ_EXT6
+#define PIRQD MPC83xx_IRQ_EXT7
+
+#define MPC83xx_PCI1_LOWER_IO 0x00000000
+#define MPC83xx_PCI1_UPPER_IO 0x00ffffff
+#define MPC83xx_PCI1_LOWER_MEM 0x80000000
+#define MPC83xx_PCI1_UPPER_MEM 0x9fffffff
+#define MPC83xx_PCI1_IO_BASE 0xe2000000
+#define MPC83xx_PCI1_MEM_OFFSET 0x00000000
+#define MPC83xx_PCI1_IO_SIZE 0x01000000
+
+#define MPC83xx_PCI2_LOWER_IO 0x00000000
+#define MPC83xx_PCI2_UPPER_IO 0x00ffffff
+#define MPC83xx_PCI2_LOWER_MEM 0xa0000000
+#define MPC83xx_PCI2_UPPER_MEM 0xbfffffff
+#define MPC83xx_PCI2_IO_BASE 0xe3000000
+#define MPC83xx_PCI2_MEM_OFFSET 0x00000000
+#define MPC83xx_PCI2_IO_SIZE 0x01000000
#endif /* __MACH_MPC83XX_SYS_H__ */
diff --git a/arch/ppc/syslib/ppc83xx_pci.h b/arch/ppc/syslib/ppc83xx_pci.h new
file mode 100644
--- /dev/null
+++ b/arch/ppc/syslib/ppc83xx_pci.h
@@ -0,0 +1,151 @@
+/* Created by Tony Li <[EMAIL PROTECTED]>
+ * Copyright (c) 2005 freescale semiconductor
+ *
+ * This program is free software; you can redistribute it and/or
+modify it
+ * under the terms of the GNU General Public License as published by
+the
+ * Free Software Foundation; either version 2 of the License, or (at
+your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+along
+ * with this program; if not, write to the Free Software Foundation,
+Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __PPC_SYSLIB_PPC83XX_PCI_H
+#define __PPC_SYSLIB_PPC83XX_PCI_H
+
+typedef struct immr_clk {
+ u32 spmr; /* system PLL mode Register */
+ u32 occr; /* output clock control Register */
+ u32 sccr; /* system clock control Register */
+ u8 res0[0xF4];
+} immr_clk_t;
+
+/*
+ * Sequencer
+ */
+typedef struct immr_ios {
+ u32 potar0;
+ u8 res0[4];
+ u32 pobar0;
+ u8 res1[4];
+ u32 pocmr0;
+ u8 res2[4];
+ u32 potar1;
+ u8 res3[4];
+ u32 pobar1;
+ u8 res4[4];
+ u32 pocmr1;
+ u8 res5[4];
+ u32 potar2;
+ u8 res6[4];
+ u32 pobar2;
+ u8 res7[4];
+ u32 pocmr2;
+ u8 res8[4];
+ u32 potar3;
+ u8 res9[4];
+ u32 pobar3;
+ u8 res10[4];
+ u32 pocmr3;
+ u8 res11[4];
+ u32 potar4;
+ u8 res12[4];
+ u32 pobar4;
+ u8 res13[4];
+ u32 pocmr4;
+ u8 res14[4];
+ u32 potar5;
+ u8 res15[4];
+ u32 pobar5;
+ u8 res16[4];
+ u32 pocmr5;
+ u8 res17[4];
+ u8 res18[0x60];
+ u32 pmcr;
+ u8 res19[4];
+ u32 dtcr;
+ u8 res20[4];
+} immr_ios_t;
+#define POTAR_TA_MASK 0x000fffff
+#define POBAR_BA_MASK 0x000fffff
+#define POCMR_EN 0x80000000
+#define POCMR_IO 0x40000000 /* 0--memory space 1--I/O space */
+#define POCMR_SE 0x20000000 /* streaming enable */
+#define POCMR_DST 0x10000000 /* 0--PCI1 1--PCI2 */
+#define POCMR_CM_MASK 0x000fffff
+
+/*
+ * PCI Controller Control and Status Registers */ typedef struct
+immr_pcictrl {
+ u32 esr;
+ u32 ecdr;
+ u32 eer;
+ u32 eatcr;
+ u32 eacr;
+ u32 eeacr;
+ u32 edlcr;
+ u32 edhcr;
+ u32 gcr;
+ u32 ecr;
+ u32 gsr;
+ u8 res0[12];
+ u32 pitar2;
+ u8 res1[4];
+ u32 pibar2;
+ u32 piebar2;
+ u32 piwar2;
+ u8 res2[4];
+ u32 pitar1;
+ u8 res3[4];
+ u32 pibar1;
+ u32 piebar1;
+ u32 piwar1;
+ u8 res4[4];
+ u32 pitar0;
+ u8 res5[4];
+ u32 pibar0;
+ u8 res6[4];
+ u32 piwar0;
+ u8 res7[132];
+} immr_pcictrl_t;
+#define PITAR_TA_MASK 0x000fffff
+#define PIBAR_MASK 0xffffffff
+#define PIEBAR_EBA_MASK 0x000fffff
+#define PIWAR_EN 0x80000000
+#define PIWAR_PF 0x20000000
+#define PIWAR_RTT_MASK 0x000f0000
+#define PIWAR_RTT_NO_SNOOP 0x00040000
+#define PIWAR_RTT_SNOOP 0x00050000
+#define PIWAR_WTT_MASK 0x0000f000
+#define PIWAR_WTT_NO_SNOOP 0x00004000
+#define PIWAR_WTT_SNOOP 0x00005000
+#define PIWAR_IWS_MASK 0x0000003F
+#define PIWAR_IWS_4K 0x0000000B
+#define PIWAR_IWS_8K 0x0000000C
+#define PIWAR_IWS_16K 0x0000000D
+#define PIWAR_IWS_32K 0x0000000E
+#define PIWAR_IWS_64K 0x0000000F
+#define PIWAR_IWS_128K 0x00000010
+#define PIWAR_IWS_256K 0x00000011
+#define PIWAR_IWS_512K 0x00000012
+#define PIWAR_IWS_1M 0x00000013
+#define PIWAR_IWS_2M 0x00000014
+#define PIWAR_IWS_4M 0x00000015
+#define PIWAR_IWS_8M 0x00000016
+#define PIWAR_IWS_16M 0x00000017
+#define PIWAR_IWS_32M 0x00000018
+#define PIWAR_IWS_64M 0x00000019
+#define PIWAR_IWS_128M 0x0000001A
+#define PIWAR_IWS_256M 0x0000001B
+#define PIWAR_IWS_512M 0x0000001C
+#define PIWAR_IWS_1G 0x0000001D
+#define PIWAR_IWS_2G 0x0000001E
+
+#endif /* __PPC_SYSLIB_PPC83XX_PCI_H */
diff --git a/arch/ppc/syslib/ppc83xx_setup.c b/arch/ppc/syslib/ppc83xx_setup.c
--- a/arch/ppc/syslib/ppc83xx_setup.c
+++ b/arch/ppc/syslib/ppc83xx_setup.c
@@ -11,6 +11,17 @@
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ along
+ * with this program; if not, write to the Free Software Foundation,
+ Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Added PCI support -- Tony Li <[EMAIL PROTECTED]>
*/
#include <linux/config.h>
@@ -31,6 +42,10 @@
#include <asm/delay.h>
#include <syslib/ppc83xx_setup.h>
+#if defined(CONFIG_PCI)
+#include <asm/delay.h>
+#include <syslib/ppc83xx_pci.h>
+#endif
phys_addr_t immrbar;
@@ -162,4 +177,237 @@ mpc83xx_halt(void)
for(;;);
}
-/* PCI SUPPORT DOES NOT EXIT, MODEL after ppc85xx_setup.c */
+#if defined(CONFIG_PCI)
+void __init
+mpc83xx_setup_pci1(struct pci_controller *hose) {
+ u16 reg16;
+ volatile immr_pcictrl_t * pci_ctrl;
+ volatile immr_ios_t * ios;
+ bd_t *binfo = (bd_t *) __res;
+
+ pci_ctrl = ioremap(binfo->bi_immr_base + 0x8500,
sizeof(immr_pcictrl_t));
+ ios = ioremap(binfo->bi_immr_base + 0x8400, sizeof(immr_ios_t));
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+ ios->potar0 = (MPC83xx_PCI1_LOWER_MEM >> 12) & POTAR_TA_MASK;
+ ios->pobar0 = (MPC83xx_PCI1_LOWER_MEM >> 12) & POBAR_BA_MASK;
+ ios->pocmr0 = POCMR_EN |
+ (((0xffffffff - (MPC83xx_PCI1_UPPER_MEM -
+ MPC83xx_PCI1_LOWER_MEM)) >> 12) &
POCMR_CM_MASK);
+
+ /* mapped to PCI1 IO space */
+ ios->potar1 = (MPC83xx_PCI1_LOWER_IO >> 12) & POTAR_TA_MASK;
+ ios->pobar1 = (MPC83xx_PCI1_IO_BASE >> 12) & POBAR_BA_MASK;
+ ios->pocmr1 = POCMR_EN | POCMR_IO |
+ (((0xffffffff - (MPC83xx_PCI1_UPPER_IO -
+ MPC83xx_PCI1_LOWER_IO)) >> 12) & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+ pci_ctrl->pitar1 = 0x0;
+ pci_ctrl->pibar1 = 0x0;
+ pci_ctrl->piebar1 = 0x0;
+ pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
+PIWAR_WTT_SNOOP | PIWAR_IWS_2G;
+
+ /*
+ * Release PCI RST signal
+ */
+ pci_ctrl->gcr = 0;
+ udelay(2000);
+ pci_ctrl->gcr = 1;
+ udelay(2000);
+
+ reg16 = 0xff;
+ early_read_config_word(hose, hose->first_busno, 0, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ early_write_config_word(hose, hose->first_busno, 0, PCI_COMMAND,
+reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ early_write_config_word(hose, hose->first_busno, 0, PCI_STATUS, 0xffff);
+ early_write_config_byte(hose, hose->first_busno, 0, PCI_LATENCY_TIMER,
+0x80);
+
+ iounmap(pci_ctrl);
+ iounmap(ios);
+}
+
+void __init
+mpc83xx_setup_pci2(struct pci_controller *hose) {
+ u16 reg16;
+ volatile immr_pcictrl_t * pci_ctrl;
+ volatile immr_ios_t * ios;
+ bd_t *binfo = (bd_t *) __res;
+
+ pci_ctrl = ioremap(binfo->bi_immr_base + 0x8600,
sizeof(immr_pcictrl_t));
+ ios = ioremap(binfo->bi_immr_base + 0x8400, sizeof(immr_ios_t));
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+ ios->potar3 = (MPC83xx_PCI2_LOWER_MEM >> 12) & POTAR_TA_MASK;
+ ios->pobar3 = (MPC83xx_PCI2_LOWER_MEM >> 12) & POBAR_BA_MASK;
+ ios->pocmr3 = POCMR_EN | POCMR_DST |
+ (((0xffffffff - (MPC83xx_PCI2_UPPER_MEM -
+ MPC83xx_PCI2_LOWER_MEM)) >> 12) &
POCMR_CM_MASK);
+
+ /* mapped to PCI2 IO space */
+ ios->potar4 = (MPC83xx_PCI2_LOWER_IO >> 12) & POTAR_TA_MASK;
+ ios->pobar4 = (MPC83xx_PCI2_IO_BASE >> 12) & POBAR_BA_MASK;
+ ios->pocmr4 = POCMR_EN | POCMR_DST | POCMR_IO |
+ (((0xffffffff - (MPC83xx_PCI2_UPPER_IO -
+ MPC83xx_PCI2_LOWER_IO)) >> 12) & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+ pci_ctrl->pitar1 = 0x0;
+ pci_ctrl->pibar1 = 0x0;
+ pci_ctrl->piebar1 = 0x0;
+ pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
+PIWAR_WTT_SNOOP | PIWAR_IWS_2G;
+
+ /*
+ * Release PCI RST signal
+ */
+ pci_ctrl->gcr = 0;
+ udelay(2000);
+ pci_ctrl->gcr = 1;
+ udelay(2000);
+
+ reg16 = 0xff;
+ early_read_config_word(hose, hose->first_busno, 0, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ early_write_config_word(hose, hose->first_busno, 0, PCI_COMMAND,
+reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ early_write_config_word(hose, hose->first_busno, 0, PCI_STATUS, 0xffff);
+ early_write_config_byte(hose, hose->first_busno, 0, PCI_LATENCY_TIMER,
+0x80);
+
+ iounmap(pci_ctrl);
+ iounmap(ios);
+}
+
+/*
+ * PCI buses can be enabled only if SYS board combinates with PIB
+ * (Platform IO Board) board which provide 3 PCI slots. There is 2 PCI
+buses
+ * and 3 PCI slots, so people must configure the routes between them
+before
+ * enable PCI bus. This routes are under the control of PCA9555PW
+device which
+ * can be accessed via I2C bus 2 and are configured by firmware. Refer
+to
+ * Freescale to get more information about firmware configuration.
+ */
+
+extern int mpc83xx_exclude_device(u_char bus, u_char devfn); extern int
+mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel,
+ unsigned char pin);
+void __init
+mpc83xx_setup_hose(void)
+{
+ u32 val32;
+ volatile immr_clk_t * clk;
+ struct pci_controller * hose1;
+#ifdef CONFIG_MPC83xx_PCI2
+ struct pci_controller * hose2;
+#endif
+ bd_t * binfo = (bd_t *)__res;
+
+ clk = ioremap(binfo->bi_immr_base + 0xA00,
+ sizeof(immr_clk_t));
+
+ /*
+ * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
+ */
+ val32 = clk->occr;
+ udelay(2000);
+ clk->occr = 0xff000000;
+ udelay(2000);
+
+ iounmap(clk);
+
+ hose1 = pcibios_alloc_controller();
+ if(!hose1)
+ return;
+
+ ppc_md.pci_swizzle = common_swizzle;
+ ppc_md.pci_map_irq = mpc83xx_map_irq;
+
+ hose1->bus_offset = 0;
+ hose1->first_busno = 0;
+ hose1->last_busno = 0xff;
+
+ setup_indirect_pci(hose1, binfo->bi_immr_base + PCI1_CFG_ADDR_OFFSET,
+ binfo->bi_immr_base + PCI1_CFG_DATA_OFFSET);
+ hose1->set_cfg_type = 1;
+
+ mpc83xx_setup_pci1(hose1);
+
+ hose1->pci_mem_offset = MPC83xx_PCI1_MEM_OFFSET;
+ hose1->mem_space.start = MPC83xx_PCI1_LOWER_MEM;
+ hose1->mem_space.end = MPC83xx_PCI1_UPPER_MEM;
+
+ hose1->io_base_phys = MPC83xx_PCI1_IO_BASE;
+ hose1->io_space.start = MPC83xx_PCI1_LOWER_IO;
+ hose1->io_space.end = MPC83xx_PCI1_UPPER_IO; #ifdef
+CONFIG_MPC83xx_PCI2
+ isa_io_base = (unsigned long)ioremap(MPC83xx_PCI1_IO_BASE,
+ MPC83xx_PCI1_IO_SIZE + MPC83xx_PCI2_IO_SIZE); #else
+ isa_io_base = (unsigned long)ioremap(MPC83xx_PCI1_IO_BASE,
+ MPC83xx_PCI1_IO_SIZE);
+#endif /* CONFIG_MPC83xx_PCI2 */
+ hose1->io_base_virt = (void *)isa_io_base;
+ /* setup resources */
+ pci_init_resource(&hose1->io_resource,
+ MPC83xx_PCI1_LOWER_IO,
+ MPC83xx_PCI1_UPPER_IO,
+ IORESOURCE_IO, "PCI host bridge 1");
+ pci_init_resource(&hose1->mem_resources[0],
+ MPC83xx_PCI1_LOWER_MEM,
+ MPC83xx_PCI1_UPPER_MEM,
+ IORESOURCE_MEM, "PCI host bridge 1");
+
+ ppc_md.pci_exclude_device = mpc83xx_exclude_device;
+ hose1->last_busno = pciauto_bus_scan(hose1, hose1->first_busno);
+
+#ifdef CONFIG_MPC83xx_PCI2
+ hose2 = pcibios_alloc_controller();
+ if(!hose2)
+ return;
+
+ hose2->bus_offset = hose1->last_busno + 1;
+ hose2->first_busno = hose1->last_busno + 1;
+ hose2->last_busno = 0xff;
+ setup_indirect_pci(hose2, binfo->bi_immr_base + PCI2_CFG_ADDR_OFFSET,
+ binfo->bi_immr_base + PCI2_CFG_DATA_OFFSET);
+ hose2->set_cfg_type = 1;
+
+ mpc83xx_setup_pci2(hose2);
+
+ hose2->pci_mem_offset = MPC83xx_PCI2_MEM_OFFSET;
+ hose2->mem_space.start = MPC83xx_PCI2_LOWER_MEM;
+ hose2->mem_space.end = MPC83xx_PCI2_UPPER_MEM;
+
+ hose2->io_base_phys = MPC83xx_PCI2_IO_BASE;
+ hose2->io_space.start = MPC83xx_PCI2_LOWER_IO;
+ hose2->io_space.end = MPC83xx_PCI2_UPPER_IO;
+ hose2->io_base_virt = (void *)(isa_io_base + MPC83xx_PCI1_IO_SIZE);
+ /* setup resources */
+ pci_init_resource(&hose2->io_resource,
+ MPC83xx_PCI2_LOWER_IO,
+ MPC83xx_PCI2_UPPER_IO,
+ IORESOURCE_IO, "PCI host bridge 2");
+ pci_init_resource(&hose2->mem_resources[0],
+ MPC83xx_PCI2_LOWER_MEM,
+ MPC83xx_PCI2_UPPER_MEM,
+ IORESOURCE_MEM, "PCI host bridge 2");
+
+ hose2->last_busno = pciauto_bus_scan(hose2, hose2->first_busno);
+#endif /* CONFIG_MPC83xx_PCI2 */ } #endif /*CONFIG_PCI*/
diff --git a/arch/ppc/syslib/ppc83xx_setup.h b/arch/ppc/syslib/ppc83xx_setup.h
--- a/arch/ppc/syslib/ppc83xx_setup.h
+++ b/arch/ppc/syslib/ppc83xx_setup.h
@@ -12,6 +12,14 @@
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ along
+ * with this program; if not, write to the Free Software Foundation,
+ Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef __PPC_SYSLIB_PPC83XX_SETUP_H
@@ -19,7 +27,6 @@
#include <linux/config.h>
#include <linux/init.h>
-#include <asm/ppcboot.h>
extern unsigned long mpc83xx_find_end_of_memory(void) __init; extern long
mpc83xx_time_init(void) __init; @@ -31,13 +38,11 @@ extern void
mpc83xx_halt(void); extern void mpc83xx_setup_hose(void) __init;
/* PCI config */
-#if 0
-#define PCI1_CFG_ADDR_OFFSET (FIXME)
-#define PCI1_CFG_DATA_OFFSET (FIXME)
+#define PCI1_CFG_ADDR_OFFSET (0x8300)
+#define PCI1_CFG_DATA_OFFSET (0x8304)
-#define PCI2_CFG_ADDR_OFFSET (FIXME)
-#define PCI2_CFG_DATA_OFFSET (FIXME)
-#endif
+#define PCI2_CFG_ADDR_OFFSET (0x8380)
+#define PCI2_CFG_DATA_OFFSET (0x8384)
/* Serial Config */
#ifdef CONFIG_SERIAL_MANY_PORTS
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
