Hi Chaithrika,
My apologies for the delay, but here are (finally!) my review comments:
On Wednesday 08 April 2009 13:18:27 Chaithrika U S wrote:
> Platform specific display device setup for DM646x EVM
>
> Add platform device and resource structures. Also define a platform specific
> clock setup function that can be accessed by the driver to configure the clock
> and CPLD.
>
> This patch is dependent on a patch submitted earlier, that patch adds
> Pin Mux and clock definitions for Video on DM646x.
>
> Signed-off-by: Manjunath Hadli <m...@ti.com>
> Signed-off-by: Brijesh Jadav <brijes...@ti.com>
> Signed-off-by: Chaithrika U S <chaithr...@ti.com>
> ---
> Applies to DaVinci GIT tree
>
> arch/arm/mach-davinci/board-dm646x-evm.c | 138
> +++++++++++++++++++++++++++
> arch/arm/mach-davinci/dm646x.c | 63 ++++++++++++
> arch/arm/mach-davinci/include/mach/dm646x.h | 25 +++++
> 3 files changed, 226 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c
> b/arch/arm/mach-davinci/board-dm646x-evm.c
> index bcf11d5..9071a39 100644
> --- a/arch/arm/mach-davinci/board-dm646x-evm.c
> +++ b/arch/arm/mach-davinci/board-dm646x-evm.c
> @@ -39,6 +39,7 @@
> #include <mach/serial.h>
> #include <mach/i2c.h>
> #include <mach/mmc.h>
> +#include <mach/mux.h>
>
> #include <linux/platform_device.h>
> #include <linux/i2c.h>
> @@ -49,6 +50,19 @@
> #define DM646X_EVM_PHY_MASK (0x2)
> #define DM646X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
>
> +#define VIDCLKCTL_OFFSET (0x38)
> +#define VSCLKDIS_OFFSET (0x6c)
> +
> +#define VCH2CLK_MASK (BIT_MASK(10) | BIT_MASK(9) | BIT_MASK(8))
> +#define VCH2CLK_SYSCLK8 (BIT(9))
> +#define VCH2CLK_AUXCLK (BIT(9) | BIT(8))
> +#define VCH3CLK_MASK (BIT_MASK(14) | BIT_MASK(13) | BIT_MASK(12))
> +#define VCH3CLK_SYSCLK8 (BIT(13))
> +#define VCH3CLK_AUXCLK (BIT(14) | BIT(13))
> +
> +#define VIDCH2CLK (BIT(10))
> +#define VIDCH3CLK (BIT(11))
> +
> static struct emac_platform_data dm646x_evm_emac_pdata = {
> .phy_mask = DM646X_EVM_PHY_MASK,
> .mdio_max_freq = DM646X_EVM_MDIO_FREQUENCY,
> @@ -103,11 +117,54 @@ int dm646xevm_eeprom_write(void *buf, off_t off, size_t
> count)
> }
> EXPORT_SYMBOL(dm646xevm_eeprom_write);
>
> +static struct i2c_client *cpld_client;
> +
> +static int cpld_video_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + cpld_client = client;
> + return 0;
> +}
> +
> +static int __devexit cpld_video_remove(struct i2c_client *client)
> +{
> + cpld_client = NULL;
> + return 0;
> +}
> +
> +static const struct i2c_device_id cpld_video_id[] = {
> + { "cpld_video", 0 },
> + { }
> +};
> +
> +static struct i2c_driver cpld_video_driver = {
> + .driver = {
> + .name = "cpld_video",
> + },
> + .probe = cpld_video_probe,
> + .remove = cpld_video_remove,
> + .id_table = cpld_video_id,
> +};
> +
> +static void evm_init_cpld(void)
> +{
> + i2c_add_driver(&cpld_video_driver);
> +}
> +
> static struct i2c_board_info __initdata i2c_info[] = {
> {
> I2C_BOARD_INFO("24c256", 0x50),
> .platform_data = &eeprom_info,
> },
> + {
> + I2C_BOARD_INFO("adv7343", 0x2A),
> + },
> + {
> + I2C_BOARD_INFO("ths7303", 0x2C),
> + },
Is it necessary to add the v4l2 subdevs here? I think it is better to use
dm646x_vpif_subdev instead and rely on v4l2_i2c_new_subdev to initialize
the subdev. I strongly recommend using the v4l2_i2c_new* functions since
these are guaranteed to load and lock modules correctly.
> + {
> + I2C_BOARD_INFO("cpld_video", 0x3B),
> + },
> };
>
> static struct davinci_i2c_platform_data i2c_pdata = {
> @@ -115,10 +172,90 @@ static struct davinci_i2c_platform_data i2c_pdata = {
> .bus_delay = 0 /* usec */,
> };
>
> +static int set_vpif_clock(int mux_mode, int hd)
> +{
> + int val = 0;
> + int err = 0;
> + unsigned int value;
> + void __iomem *base = IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE);
> +
> + /* disable the clock */
> + value = __raw_readl(base + VSCLKDIS_OFFSET);
> + value |= (VIDCH3CLK | VIDCH2CLK);
> + __raw_writel(value, base + VSCLKDIS_OFFSET);
> +
> + val = i2c_smbus_read_byte(cpld_client);
> + if (val < 0)
> + return val;
> +
> + if (mux_mode == 1)
> + val &= ~0x40;
> + else
> + val |= 0x40;
> +
> + err = i2c_smbus_write_byte(cpld_client, val);
> + if (err)
> + return err;
> +
> + value = __raw_readl(base + VIDCLKCTL_OFFSET);
> + value &= ~(VCH2CLK_MASK);
> + value &= ~(VCH3CLK_MASK);
> +
> + if (hd >= 1)
> + value |= (VCH2CLK_SYSCLK8 | VCH3CLK_SYSCLK8);
> + else
> + value |= (VCH2CLK_AUXCLK | VCH3CLK_AUXCLK);
> +
> + __raw_writel(value, base + VIDCLKCTL_OFFSET);
> +
> + /* enable the clock */
> + value = __raw_readl(base + VSCLKDIS_OFFSET);
> + value &= ~(VIDCH3CLK | VIDCH2CLK);
> + __raw_writel(value, base + VSCLKDIS_OFFSET);
> +
> + return 0;
> +}
> +
> +static const struct subdev_info dm646x_vpif_subdev[] = {
> + {
> + .addr = 0x2A,
> + .name = "adv7343",
> + },
> + {
> + .addr = 0x2C,
> + .name = "ths7303",
> + },
> +};
> +
> +static struct vpif_output output[] = {
Should be const.
> + {
> + .id = 0,
> + .name = "Composite"
> + },
> + {
> + .id = 1,
> + .name = "Component"
> + },
> + {
> + .id = 2,
> + .name = "S-Video"
> + },
> +};
Is there any need to include the id field? I can't imagine a case where
there are holes in the id sequence.
> +
> +static struct vpif_config dm646x_vpif_config = {
> + .set_clock = set_vpif_clock,
> + .subdevinfo = (struct subdev_info *)dm646x_vpif_subdev,
Why is the cast needed here? .subdevinfo should be a const pointer as well.
> + .subdev_count = ARRAY_SIZE(dm646x_vpif_subdev),
> + .output = output,
> + .output_count = ARRAY_SIZE(output),
> + .card_name = "DM646x EVM",
> +};
> +
> static void __init evm_init_i2c(void)
> {
> davinci_init_i2c(&i2c_pdata);
> i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
> + evm_init_cpld();
> }
>
> static void __init davinci_map_io(void)
> @@ -132,6 +269,7 @@ static __init void evm_init(void)
> evm_init_i2c();
> davinci_serial_init(&uart_config);
> davinci_init_emac(&dm646x_evm_emac_pdata);
> + dm646x_setup_vpif(&dm646x_vpif_config);
> }
>
> static __init void davinci_dm646x_evm_irq_init(void)
> diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c
> index b302f12..a94cb86 100644
> --- a/arch/arm/mach-davinci/dm646x.c
> +++ b/arch/arm/mach-davinci/dm646x.c
> @@ -12,6 +12,7 @@
> #include <linux/init.h>
> #include <linux/clk.h>
> #include <linux/platform_device.h>
> +#include <linux/dma-mapping.h>
>
> #include <mach/dm646x.h>
> #include <mach/clock.h>
> @@ -24,6 +25,15 @@
> #include "clock.h"
> #include "mux.h"
>
> +#define DAVINCI_VPIF_BASE (0x01C12000)
> +#define VDD3P3V_PWDN_OFFSET (0x48)
> +#define VSCLKDIS_OFFSET (0x6C)
> +
> +#define VDD3P3V_VID_MASK (BIT_MASK(7) | BIT_MASK(6) | BIT_MASK(5) |\
> + BIT_MASK(4))
> +#define VSCLKDIS_MASK (BIT_MASK(11) | BIT_MASK(10) |
> BIT_MASK(9) |\
> + BIT_MASK(8))
> +
> /*
> * Device specific clocks
> */
> @@ -421,8 +431,61 @@ static struct platform_device dm646x_edma_device = {
> .resource = edma_resources,
> };
>
> +static u64 vpif_dma_mask = DMA_32BIT_MASK;
> +
> +static struct resource vpif_resource[] = {
> + {
> + .start = DAVINCI_VPIF_BASE,
> + .end = DAVINCI_VPIF_BASE + 0x03fff,
> + .flags = IORESOURCE_MEM,
> + },
> + {
> + .start = IRQ_DM646X_VP_VERTINT2,
> + .end = IRQ_DM646X_VP_VERTINT2,
> + .flags = IORESOURCE_IRQ,
> + },
> + {
> + .start = IRQ_DM646X_VP_VERTINT3,
> + .end = IRQ_DM646X_VP_VERTINT3,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> +static struct platform_device vpif_display_dev = {
> + .name = "vpif_display",
> + .id = -1,
> + .dev = {
> + .dma_mask = &vpif_dma_mask,
> + .coherent_dma_mask = DMA_32BIT_MASK,
> + },
> + .resource = vpif_resource,
> + .num_resources = ARRAY_SIZE(vpif_resource),
> +};
> +
> /*----------------------------------------------------------------------*/
>
> +void dm646x_setup_vpif(struct vpif_config *config)
> +{
> + unsigned int value;
> + void __iomem *base = IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE);
> +
> + value = __raw_readl(base + VSCLKDIS_OFFSET);
> + value &= ~VSCLKDIS_MASK;
> + __raw_writel(value, base + VSCLKDIS_OFFSET);
> +
> + value = __raw_readl(base + VDD3P3V_PWDN_OFFSET);
> + value &= ~VDD3P3V_VID_MASK;
> + __raw_writel(value, base + VDD3P3V_PWDN_OFFSET);
> +
> + davinci_cfg_reg(DM646X_STSOMUX_DISABLE);
> + davinci_cfg_reg(DM646X_STSIMUX_DISABLE);
> + davinci_cfg_reg(DM646X_PTSOMUX_DISABLE);
> + davinci_cfg_reg(DM646X_PTSIMUX_DISABLE);
> +
> + vpif_display_dev.dev.platform_data = config;
> + platform_device_register(&vpif_display_dev);
> +}
> +
> #if defined(CONFIG_TI_DAVINCI_EMAC) || defined(CONFIG_TI_DAVINCI_EMAC_MODULE)
>
> void dm646x_init_emac(struct emac_platform_data *pdata)
> diff --git a/arch/arm/mach-davinci/include/mach/dm646x.h
> b/arch/arm/mach-davinci/include/mach/dm646x.h
> index 02ce872..2f9a1d8 100644
> --- a/arch/arm/mach-davinci/include/mach/dm646x.h
> +++ b/arch/arm/mach-davinci/include/mach/dm646x.h
> @@ -12,6 +12,7 @@
> #define __ASM_ARCH_DM646X_H
>
> #include <linux/platform_device.h>
> +#include <linux/i2c.h>
> #include <mach/hardware.h>
> #include <mach/emac.h>
>
> @@ -25,4 +26,28 @@
> void __init dm646x_init(void);
> void dm646x_init_emac(struct emac_platform_data *pdata);
>
> +void dm646x_video_init(void);
> +
> +struct vpif_output {
> + u16 id;
> + const char *name;
> +};
> +
> +struct subdev_info {
> + u8 addr;
> + const char *name;
> +};
> +
> +struct vpif_config {
> + int (*set_clock)(int, int);
> + struct subdev_info *subdevinfo;
Should be a const pointer.
> + int subdev_count;
> + struct vpif_output *output;
Ditto.
> + int output_count;
> + const char *card_name;
> +};
> +
> +
> +void dm646x_setup_vpif(struct vpif_config *config);
> +
> #endif /* __ASM_ARCH_DM646X_H */
Regards,
Hans
--
Hans Verkuil - video4linux developer - sponsored by TANDBERG
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
