Hi Rob, Geert, Laurent,
Thank you for the review comments.
> On Mon, Nov 14, 2016 at 8:52 PM, Rob Herring <r...@kernel.org> wrote:
> > On Thu, Nov 10, 2016 at 11:22:20AM +0200, Laurent Pinchart wrote:
> >> On Wednesday 09 Nov 2016 15:44:44 Ramesh Shanmugasundaram wrote:
> >> > --- /dev/null
> >> > +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt
> >> > @@ -0,0 +1,136 @@
>
> >> > +Example
> >> > +--------
> >> > +
> >> > +SoC common dtsi file
> >> > +
> >> > + drif00: rif@e6f40000 {
> >> > + compatible = "renesas,r8a7795-drif",
> >> > + "renesas,rcar-gen3-drif";
> >> > + reg = <0 0xe6f40000 0 0x64>;
> >> > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> >> > + clocks = <&cpg CPG_MOD 515>;
> >> > + clock-names = "fck";
> >> > + dmas = <&dmac1 0x20>, <&dmac2 0x20>;
> >> > + dma-names = "rx", "rx";
> >
> > rx, rx? That doesn't make sense. While we don't explicitly disallow
> > this, I'm thinking we should. I wonder if there's any case this is
> > valid. If not, then a dtc check for this could be added.
>
> The device can be used with either dmac1 or dmac2.
> Which one is used is decided at run time, based on the availability of DMA
> channels per DMAC, which is a limited resource.
>
Yep.
> >> > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> >> > + status = "disabled";
> >> > + };
> >> > +
> >> > + drif01: rif@e6f50000 {
> >> > + compatible = "renesas,r8a7795-drif",
> >> > + "renesas,rcar-gen3-drif";
> >> > + reg = <0 0xe6f50000 0 0x64>;
> >> > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> >> > + clocks = <&cpg CPG_MOD 514>;
> >> > + clock-names = "fck";
> >> > + dmas = <&dmac1 0x22>, <&dmac2 0x22>;
> >> > + dma-names = "rx", "rx";
> >> > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> >> > + status = "disabled";
> >> > + };
> >> > +
> >> > + drif0: rif@0 {
> >> > + compatible = "renesas,r8a7795-drif",
> >> > + "renesas,rcar-gen3-drif";
> >> > + sub-channels = <&drif00>, <&drif01>;
> >> > + status = "disabled";
> >> > + };
> >>
> >> I'm afraid this really hurts my eyes, especially using the same
> >> compatible string for both the channel and sub-channel nodes.
> >>
> >> We need to decide how to model the hardware in DT. Given that the two
> >> channels are mostly independent having separate DT nodes makes sense
> >> to me. However, as they share the clock and sync signals, somehow
> >> grouping them makes sense. I see three ways to do so, and there might
> be more.
> >>
> >> 1. Adding an extra DT node for the channels group, with phandles to
> >> the two channels. This is what you're proposing here.
> >>
> >> 2. Adding an extra DT node for the channels group, as a parent of the
> >> two channels.
> >>
> >> 3. Adding phandles to the channels, pointing to each other, or
> >> possibly a phandle from channel 0 pointing to channel 1.
> >>
> >> Neither of these options seem perfect to me. I don't like option 1 as
> >> the group DT node really doesn't describe a hardware block. If we
> >> want to use a DT node to convey group information, option 2 seems
> >> better to me. However, it somehow abuses the DT parent-child model
> >> that is supposed to describe relationships from a control bus point
> >> of view. Option 3 has the drawback of not scaling properly, at least
> >> with phandles in both channels pointing to the other one.
> >>
> >> Rob, Geert, tell me you have a fourth idea I haven't thought of that
> >> would solve all those problems :-)
> >
> > What's the purpose/need for grouping them?
> >
> > I'm fine with Option 2, though I want to make sure it is really needed.
>
> Each half of a DRIF pair is basically an SPI slave controller without TX
> capability, sharing clock and chip-select between the two halves.
> Hence you can use either one half to receive 1 bit per clock pulse, or
> both halves to receive 2 bits per clock pulse.
> You cannot use both halves for independent operation due to the signal
> sharing.
Is the below model looks OK? I assume this is Option 2. Any preferences on the
"parent" compatible string please?
---------------------------------------------------------
drif0: rif@0 {
compatible = "renesas,rcar-gen3-drif", "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
status = "disabled";
drif00: rif@e6f40000 {
compatible = "renesas,r8a7795-drif",
"renesas,rcar-gen3-drif";
reg = <0 0xe6f40000 0 0x64>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 515>;
clock-names = "fck";
dmas = <&dmac1 0x20>, <&dmac2 0x20>;
dma-names = "rx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
drif01: rif@e6f50000 {
compatible = "renesas,r8a7795-drif",
"renesas,rcar-gen3-drif";
reg = <0 0xe6f50000 0 0x64>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 514>;
clock-names = "fck";
dmas = <&dmac1 0x22>, <&dmac2 0x22>;
dma-names = "rx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
};
---------------------------------------------------------
Thanks in advance,
Ramesh
