Hello! On 09.01.17 18:59, Antti Palosaari wrote: > > > On 01/09/2017 05:23 PM, Oleh Kravchenko wrote: >> This patch provide only digital support. >> >> The device is based on Si2168 30-demodulator, >> Si2158-20 tuner and CX23102-11Z chipset; >> USB id: 1b80:d3b2. >> >> Status: >> - DVB-T2 works fine; >> - Composite and SVideo works fine; >> - Analog not implemented. >> >> Signed-off-by: Oleh Kravchenko <o...@kaa.org.ua> >> Tested-by: Oleh Kravchenko <o...@kaa.org.ua> >> --- >> drivers/media/usb/cx231xx/Kconfig | 1 + >> drivers/media/usb/cx231xx/cx231xx-cards.c | 29 +++++++++++++ >> drivers/media/usb/cx231xx/cx231xx-dvb.c | 71 >> +++++++++++++++++++++++++++++++ >> drivers/media/usb/cx231xx/cx231xx-i2c.c | 37 ++++++++++++++++ >> drivers/media/usb/cx231xx/cx231xx.h | 1 + >> 5 files changed, 139 insertions(+) >> >> diff --git a/drivers/media/usb/cx231xx/Kconfig >> b/drivers/media/usb/cx231xx/Kconfig >> index 0cced3e..58de80b 100644 >> --- a/drivers/media/usb/cx231xx/Kconfig >> +++ b/drivers/media/usb/cx231xx/Kconfig >> @@ -50,6 +50,7 @@ config VIDEO_CX231XX_DVB >> select DVB_LGDT3306A if MEDIA_SUBDRV_AUTOSELECT >> select DVB_TDA18271C2DD if MEDIA_SUBDRV_AUTOSELECT >> select DVB_SI2165 if MEDIA_SUBDRV_AUTOSELECT >> + select DVB_SI2168 if MEDIA_SUBDRV_AUTOSELECT >> select MEDIA_TUNER_SI2157 if MEDIA_SUBDRV_AUTOSELECT >> >> ---help--- >> diff --git a/drivers/media/usb/cx231xx/cx231xx-cards.c >> b/drivers/media/usb/cx231xx/cx231xx-cards.c >> index 36bc254..9b1df5a 100644 >> --- a/drivers/media/usb/cx231xx/cx231xx-cards.c >> +++ b/drivers/media/usb/cx231xx/cx231xx-cards.c >> @@ -841,6 +841,33 @@ struct cx231xx_board cx231xx_boards[] = { >> .gpio = NULL, >> } }, >> }, >> + [CX231XX_BOARD_EVROMEDIA_FULL_HYBRID_FULLHD] = { >> + .name = "Evromedia USB Full Hybrid Full HD", >> + .tuner_type = TUNER_ABSENT, >> + .demod_addr = 0xc8 >> 1, >> + .demod_i2c_master = I2C_1_MUX_3, >> + .has_dvb = 1, >> + .ir_i2c_master = I2C_0, >> + .norm = V4L2_STD_PAL, >> + .output_mode = OUT_MODE_VIP11, >> + .tuner_addr = 0xc0 >> 1, > > These "8-bit" I2C addresses looks funny, but if that's used by cx231xx driver > then leave...
To avoid misunderstanding, Windows driver use shifted i2c addresses. >> + .tuner_i2c_master = I2C_2, >> + .input = {{ >> + .type = CX231XX_VMUX_TELEVISION, >> + .vmux = 0, >> + .amux = CX231XX_AMUX_VIDEO, >> + }, { >> + .type = CX231XX_VMUX_COMPOSITE1, >> + .vmux = CX231XX_VIN_2_1, >> + .amux = CX231XX_AMUX_LINE_IN, >> + }, { >> + .type = CX231XX_VMUX_SVIDEO, >> + .vmux = CX231XX_VIN_1_1 | >> + (CX231XX_VIN_1_2 << 8) | >> + CX25840_SVIDEO_ON, >> + .amux = CX231XX_AMUX_LINE_IN, >> + } }, >> + }, >> }; >> const unsigned int cx231xx_bcount = ARRAY_SIZE(cx231xx_boards); >> >> @@ -908,6 +935,8 @@ struct usb_device_id cx231xx_id_table[] = { >> .driver_info = CX231XX_BOARD_OTG102}, >> {USB_DEVICE(USB_VID_TERRATEC, 0x00a6), >> .driver_info = CX231XX_BOARD_TERRATEC_GRABBY}, >> + {USB_DEVICE(0x1b80, 0xd3b2), >> + .driver_info = CX231XX_BOARD_EVROMEDIA_FULL_HYBRID_FULLHD}, >> {}, >> }; >> >> diff --git a/drivers/media/usb/cx231xx/cx231xx-dvb.c >> b/drivers/media/usb/cx231xx/cx231xx-dvb.c >> index 1417515..08472a3 100644 >> --- a/drivers/media/usb/cx231xx/cx231xx-dvb.c >> +++ b/drivers/media/usb/cx231xx/cx231xx-dvb.c >> @@ -33,6 +33,7 @@ >> #include "s5h1411.h" >> #include "lgdt3305.h" >> #include "si2165.h" >> +#include "si2168.h" >> #include "mb86a20s.h" >> #include "si2157.h" >> #include "lgdt3306a.h" >> @@ -949,6 +950,76 @@ static int dvb_init(struct cx231xx *dev) >> &pv_tda18271_config); >> break; >> >> + case CX231XX_BOARD_EVROMEDIA_FULL_HYBRID_FULLHD: >> + { >> + struct si2157_config si2157_config = {}; >> + struct si2168_config si2168_config = {}; >> + struct i2c_board_info info = {}; >> + struct i2c_client *client; >> + struct i2c_adapter *adapter; >> + >> + /* attach demodulator chip */ >> + si2168_config.ts_mode = SI2168_TS_SERIAL; /* from *.inf file */ >> + si2168_config.fe = &dev->dvb->frontend; >> + si2168_config.i2c_adapter = &adapter; >> + si2168_config.ts_clock_inv = true; >> + >> + strlcpy(info.type, "si2168", info.type); >> + info.addr = dev->board.demod_addr; >> + info.platform_data = &si2168_config; >> + >> + request_module(info.type); >> + client = i2c_new_device(demod_i2c, &info); >> + >> + if (client == NULL || client->dev.driver == NULL || >> dev->dvb->frontend == NULL) { > > No need to check frontend here, or at least I cannot see why it should? Does > the cx231xx initialize with some special value before calling si2168 probe - > which will set it? client and driver will be null in case si2168 probe fails. > Also, frontend pointer is not set if si2168 probe fails. > I just copy code from CX231XX_BOARD_HAUPPAUGE_930C_HD_1114xx case, are you sure about it? >> + dev_err(dev->dev, "Failed to attach Si2168 front end\n"); >> + result = -EINVAL; >> + goto out_free; >> + } >> + >> + if (!try_module_get(client->dev.driver->owner)) { >> + i2c_unregister_device(client); >> + result = -ENODEV; >> + goto out_free; >> + } >> + >> + dvb->i2c_client_demod = client; >> + dev->dvb->frontend->ops.i2c_gate_ctrl = NULL; > > si2168 does not use nor set i2c_gate_ctrl callback. No need to nullify it in > any case. Done! >> + dvb->frontend->callback = cx231xx_tuner_callback; >> + >> + /* attach tuner chip */ >> + si2157_config.fe = dev->dvb->frontend; >> +#ifdef CONFIG_MEDIA_CONTROLLER_DVB >> + si2157_config.mdev = dev->media_dev; >> +#endif >> + si2157_config.if_port = 1; >> + si2157_config.inversion = false; >> + >> + memset(&info, 0, sizeof(info)); >> + strlcpy(info.type, "si2157", info.type); >> + info.addr = dev->board.tuner_addr; >> + info.platform_data = &si2157_config; >> + >> + request_module("si2157"); >> + client = i2c_new_device(tuner_i2c, &info); >> + >> + if (client == NULL || client->dev.driver == NULL) { >> + dvb_frontend_detach(dev->dvb->frontend); >> + result = -ENODEV; >> + goto out_free; >> + } > > Does this error handling work? Have you tested it? I suspect it will not. You > should likely decrease si2168 module reference counter and then unregister > si2168 driver. > The same error handling for CX231XX_BOARD_HAUPPAUGE_930C_HD_1114xx, why it bad? >> + >> + if (!try_module_get(client->dev.driver->owner)) { >> + i2c_unregister_device(client); >> + dvb_frontend_detach(dev->dvb->frontend); >> + result = -ENODEV; >> + goto out_free; >> + } >> + >> + dev->cx231xx_reset_analog_tuner = NULL; >> + dev->dvb->i2c_client_tuner = client; >> + break; >> + } >> default: >> dev_err(dev->dev, >> "%s/2: The frontend of your DVB/ATSC card isn't supported >> yet\n", >> diff --git a/drivers/media/usb/cx231xx/cx231xx-i2c.c >> b/drivers/media/usb/cx231xx/cx231xx-i2c.c >> index 35e9acf..60412ec 100644 >> --- a/drivers/media/usb/cx231xx/cx231xx-i2c.c >> +++ b/drivers/media/usb/cx231xx/cx231xx-i2c.c >> @@ -171,6 +171,43 @@ static int cx231xx_i2c_send_bytes(struct i2c_adapter >> *i2c_adap, >> bus->i2c_nostop = 0; >> bus->i2c_reserve = 0; >> >> + } else if (dev->model == CX231XX_BOARD_EVROMEDIA_FULL_HYBRID_FULLHD >> + && msg->addr == dev->tuner_addr >> + && msg->len > 4) { >> + /* special case for Evromedia USB Full Hybrid Full HD tuner chip */ >> + size = msg->len; >> + saddr_len = 1; >> + >> + /* adjust the length to correct length */ >> + size -= saddr_len; >> + >> + buf_ptr = (u8*)(msg->buf + 1); >> + >> + do { >> + /* prepare xfer_data struct */ >> + req_data.dev_addr = msg->addr; >> + req_data.direction = msg->flags; >> + req_data.saddr_len = saddr_len; >> + req_data.saddr_dat = msg->buf[0]; >> + req_data.buf_size = size > 4 ? 4 : size; >> + req_data.p_buffer = (u8*)(buf_ptr + loop * 4); >> + >> + bus->i2c_nostop = (size > 4) ? 1 : 0; >> + bus->i2c_reserve = (loop == 0) ? 0 : 1; >> + >> + /* usb send command */ >> + status = dev->cx231xx_send_usb_command(bus, &req_data); >> + loop++; >> + >> + if (size >= 4) { >> + size -= 4; >> + } else { >> + size = 0; >> + } >> + } while (size > 0); >> + >> + bus->i2c_nostop = 0; >> + bus->i2c_reserve = 0; > > I don't follow (and I looked only that patch, not whole cx231xx driver) why > this I2C adapter logic is limited to that device only. si2168 and si2157 > drivers applies just standard multibyte I2C read and write operations - no > write+read op used at all. > > These I2C adapter routines should be same for every device. Maybe original > logic is somehow wrong and it should be fixed instead of adding new device > specific logic. I can rewrite it, but who will test it? :) >> } else { /* regular case */ >> >> /* prepare xfer_data struct */ >> diff --git a/drivers/media/usb/cx231xx/cx231xx.h >> b/drivers/media/usb/cx231xx/cx231xx.h >> index 90c8676..d9792ea 100644 >> --- a/drivers/media/usb/cx231xx/cx231xx.h >> +++ b/drivers/media/usb/cx231xx/cx231xx.h >> @@ -78,6 +78,7 @@ >> #define CX231XX_BOARD_HAUPPAUGE_930C_HD_1114xx 20 >> #define CX231XX_BOARD_HAUPPAUGE_955Q 21 >> #define CX231XX_BOARD_TERRATEC_GRABBY 22 >> +#define CX231XX_BOARD_EVROMEDIA_FULL_HYBRID_FULLHD 23 >> >> /* Limits minimum and default number of buffers */ >> #define CX231XX_MIN_BUF 4 >> > > regards > Antti > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html