On 2017/8/23 18:37, Hans Verkuil wrote:
On 08/22/17 09:30, wenyou.y...@microchip.com wrote:
Hi Hans,
-----Original Message-----
From: Hans Verkuil [mailto:hverk...@xs4all.nl]
Sent: 2017年8月22日 15:00
To: Wenyou Yang - A41535 <wenyou.y...@microchip.com>; Mauro Carvalho
Chehab <mche...@s-opensource.com>
Cc: Nicolas Ferre - M43238 <nicolas.fe...@microchip.com>; linux-
ker...@vger.kernel.org; Sakari Ailus <sakari.ai...@iki.fi>; Jonathan Corbet
<cor...@lwn.net>; linux-arm-ker...@lists.infradead.org; Linux Media Mailing List
<linux-media@vger.kernel.org>
Subject: Re: [PATCH 1/3] media: atmel-isc: Not support RBG format from sensor.
On 08/22/2017 03:18 AM, Yang, Wenyou wrote:
Hi Hans,
On 2017/8/21 22:07, Hans Verkuil wrote:
On 08/17/2017 09:16 AM, Wenyou Yang wrote:
The 12-bit parallel interface supports the Raw Bayer, YCbCr,
Monochrome and JPEG Compressed pixel formats from the external
sensor, not support RBG pixel format.
Signed-off-by: Wenyou Yang <wenyou.y...@microchip.com>
---
drivers/media/platform/atmel/atmel-isc.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/media/platform/atmel/atmel-isc.c
b/drivers/media/platform/atmel/atmel-isc.c
index d4df3d4ccd85..535bb03783fe 100644
--- a/drivers/media/platform/atmel/atmel-isc.c
+++ b/drivers/media/platform/atmel/atmel-isc.c
@@ -1478,6 +1478,11 @@ static int isc_formats_init(struct isc_device *isc)
while (!v4l2_subdev_call(subdev, pad, enum_mbus_code,
NULL, &mbus_code)) {
mbus_code.index++;
+
+ /* Not support the RGB pixel formats from sensor */
+ if ((mbus_code.code & 0xf000) == 0x1000)
+ continue;
Am I missing something? Here you skip any RGB mediabus formats, but
in patch 3/3 you add RGB mediabus formats. But this patch prevents
those new formats from being selected, right?
This patch prevents getting the RGB format from the sensor directly.
The RGB format can be produced by ISC controller by itself.
OK, I think I see what is going on here. The isc_formats array really is two
arrays
in one: up to RAW_FMT_IND_END it describes what it can receive from the
source, and after that it describes what it can convert it to.
Not exactly.
Yes, up to RAW_FMT_IND_END, these formats must be got from the senor, they are
RAW formats.
From ISC_FMT_IND_START to ISC_FMT_IND_END, they can be generated by the ISC
controller.
It is possible they can be got from the sensor too, the driver will check it.
If it can be got from both the sensor and the ISC controller, the user can use the
"sensor_preferred" parameter to decide from which one to get.
The RBG formats are the exception.
But if you can't handle RGB formats from the sensor, then why not make sure
none of the mbus codes in isc_formats uses RGB? That makes much more sense.
E.g.:
{ V4L2_PIX_FMT_RGB565, MEDIA_BUS_FMT_RGB565_2X8_LE, 16,
ISC_PFE_CFG0_BPS_EIGHT, ISC_BAY_CFG_BGBG,
ISC_RLP_CFG_MODE_RGB565,
ISC_DCFG_IMODE_PACKED16, ISC_DCTRL_DVIEW_PACKED, 0x7b,
false, false },
Why use MEDIA_BUS_FMT_RGB565_2X8_LE if this apparently is not supported?
This array is also the lists of all formats supported by the ISC(including got
from the sensor).
The RGB formats are only generated by the ISC controller, not from the sensor.
You're adding code that skips any entries of the table where mbus_code is an
RGB code. But this can also be done by not having RGB mbus codes in the table
in the first place since they make no sense if the HW cannot handle that!
Set the mbus_code to e.g. 0 for such entries, that makes more sense.
I also strongly suggest changing how the table is organized since those
_FMT_IND_ indices are all to easy to get wrong (and frankly hard to understand).
Yes, you are right, I will change it. Do you have some advice?
Thank you.
Regards,
Hans
Regards,
Hans
Regards,
Hans
+
fmt = find_format_by_code(mbus_code.code, &i);
if (!fmt)
continue;
Best Regards,
Wenyou Yang
Best Regards,
Wenyou Yang
Best Regards,
Wenyou Yang
