Em Wed, 27 Jun 2018 14:41:22 -0500
Brad Love <b...@nextdimension.cc> escreveu:
> When dual transport stream support was added the call to set
> alt mode on the USB interface was moved to em28xx_dvb_init.
> This was reported to break streaming for a device, so the
> call was re-added to em28xx_start_streaming.
>
> Commit 509f89652f83 ("media: em28xx: fix a regression with HVR-950")
>
> This regression fix however broke dual transport stream support.
> When a tuner starts streaming it sets alt mode on the USB interface.
> The problem is both tuners share the same USB interface, so when
> the second tuner becomes active and sets alt mode on the interface
> it kills streaming on the other port.
>
> It was suggested add a refcount somewhere and only set alt mode if
> no tuners are currently active on the interface. This requires
> sharing some state amongst both tuner devices, with appropriate
> locking.
>
> What I've done here is the following:
> - Add a usage_count pointer to struct em28xx
> - Share usage_count between both em28xx devices
> - Only set alt mode if usage_count is zero
> - Increment usage_count when each tuner becomes active
> - Decrement usage_count when a tuner becomes idle
>
> With usage_count in the main em28xx struct, locking is handled as
> follows:
> - if a secondary tuner exists, lock dev->dev_next->lock
> - if no secondary tuner exists, lock dev->lock
>
> By using the above scheme a single tuner device, will lock itself,
> the first tuner in a dual tuner device will lock the second tuner,
> and the second tuner in a dual tuner device will lock itself aka
> the second tuner instance.
>
> This is a perhaps a little hacky, which is why I've added the RFC.
> A quick solution was required though, so I don't fix a couple
> newer Hauppauge devices, just to break a lot of older ones.
Hi Brad,
I didn't look at the patches, just at the description. IMHO,
the proposed approach won't work.
I suspect that it will require a redesign of the alternate setting
logic, but we have to handle first with the regressions.
So, I'll break this into two separate issues
1) HVR-950 x dual mode tuners regression
HVR-950 uses a model of em28xx chipset that doesn't support dual
tuners (em2884 - I think) and has a tuner defined for analog TV.
Even on chipsets that supports dual tuners, most of the designs
come with just one.
An easier fix would be check if the device supports dual tuner.
That could be done either by checking dev->chip_id of via an
extra bit at em28xx cards struct:
unsigned int has_dual_tuners:1;
that would indicate if the device has dual tuners.
Then, decide where the alternate settings logic will happen.
That would allow a simple patch that will fix regressions with
single tuner devices while keeping Digital TV support for dual
tuners working.
A fix like that should be easy to do and to backport to older
Kernels.
IMHO, we should do it as a first approach to solve the issue,
and send with c/c to -stable.
2) Fixing the alt logic to better support dual-streaming devices
After thinking about the code changes to support dual tuner devices,
I suspect that something was missing there for the dual tuner
devices.
On a single tuner device, the alternate should be set considering
those scenarios (enumerated from less bandwidth to high bandwidth):
0) Device is not streaming
1) FM mode - just em28xx-audio sets the hardware to stream
audio via ALSA.
2) Digital TV
3) Webcam, Analog TV or Capture stream - I'll call it ATV below
for simplicity.
For all scenarios, the alternate is chosen to be the closest one to
the required bandwidth, in order to reduce latency. Still, the latency
can be somewhat painful on em28xx-based cameras.
It should be noticed that, for ATV, userspace can start streaming audio
video in any order, e. g. it can start streaming audio, then switch
to TV and start streaming video. It can also do the reverse: start
streaming video, and then start audio. The current logic was designed
and tested to support this.
I'm not sure if em28xx can support the secondary tuner on all
three different modes. If it can, with 2 tuners, that expands to 16
different combinations:
======== =======
tuner 0 tuner 1
======== =======
none none
none FM
none DTV
none ATV
FM none
FM FM
FM DTV
FM ATV
DTV none
DTV FM
DTV DTV
DTV ATV
ATV none
ATV FM
ATV DTV
ATV ATV
======== =======
Worse than that, when one tuner is active and another one starts to be
used, it may need to change the alternate, with affects the first tuner.
Not sure what happens with the pending URBs if the alternate is changed
at runtime. If this is not allowed, the driver will need to cancel all
pending URBs, switch the alternate and re-submit URBs for the first
active tuner.
The logic should also consider the case where both tuners are streamed
and one stops. Perhaps it could just keep it using the dual-tuner
alternate until both stops.
In any case, for proper alternate setting, I'm expecting to see a patch
that would touch em28xx-dvb, em28xx-audio and em28xx-v4l2, as
whatever logic it needs, it has to consider all supported combinations.
Such patch would likely be too complex for -stable.
Thanks,
Mauro
