2010/1/1 JD Louw <jd.l...@mweb.co.za>: > On Tue, 2009-12-29 at 23:23 +0200, Theunis Potgieter wrote: >> Hi mailing list, >> >> I have a problem with my Compro S300 pci card under Linux 2.6.32. >> >> I cannot tune with this card and STR/SNRA is very bad compared to my >> Technisat SkyStar 2 pci card, connected to the same dish. >> >> I have this card and are willing to run tests, tested drivers etc to >> make this work. >> >> I currently load the module saa7134 with options: card=169 >> >> I enabled some debug parameters on the saa7134, not sure what else I >> should enable. Please find my dmesg log attached. >> >> lsmod shows : >> >> # lsmod >> Module Size Used by >> zl10039 6268 2 >> mt312 12048 2 >> saa7134_dvb 41549 11 >> saa7134 195664 1 saa7134_dvb >> nfsd 416819 11 >> videobuf_dvb 8187 1 saa7134_dvb >> dvb_core 148140 1 videobuf_dvb >> ir_common 40625 1 saa7134 >> v4l2_common 21544 1 saa7134 >> videodev 58341 2 saa7134,v4l2_common >> v4l1_compat 24473 1 videodev >> videobuf_dma_sg 17830 2 saa7134_dvb,saa7134 >> videobuf_core 26534 3 saa7134,videobuf_dvb,videobuf_dma_sg >> tveeprom 12550 1 saa7134 >> thermal 20547 0 >> processor 54638 1 >> >> # uname -a >> Linux vbox 2.6.32-gentoo #4 Sat Dec 19 00:54:19 SAST 2009 i686 Pentium >> III (Coppermine) GenuineIntel GNU/Linux >> >> Thanks, >> Theunis > > Hi, > > It's probably the GPIO settings that are wrong for your SAA7133 based > card revision. See http://osdir.com/ml/linux-media/2009-06/msg01256.html > for an explanation. For quick confirmation check if you have 12V - 20V > DC going to your LNB. The relevant lines of code is in > ~/v4l-dvb/linux/drivers/media/video/saa7134/saa7134-cards.c: > > case SAA7134_BOARD_VIDEOMATE_S350: > dev->has_remote = SAA7134_REMOTE_GPIO; > saa_andorl(SAA7134_GPIO_GPMODE0 >> 2, 0x00008000, 0x00008000); > saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, 0x00008000, 0x00008000); > break; > Hi thanks for the hint. I changed it to the following:
case SAA7134_BOARD_VIDEOMATE_S350: dev->has_remote = SAA7134_REMOTE_GPIO; saa_andorl(SAA7134_GPIO_GPMODE0 >> 2, 0x0000c000, 0x0000c000); saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, 0x0000c000, 0x0000c000); break; I now get the same SNR as on my skystar2 card, signal is still indicating 17% where as the skystar2 would show 68%. At least I'm getting a LOCK on channels :) Thanks! > > Looking at your log, at least the demodulator and tuner is responding > correctly. You can see this by looking at the i2c traffic addressed to > 0x1c (demodulator) and 0xc0 (tuner). Attached is a dmesg trace from my > working SAA7130 based card. > > Regards > JD > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
