2019年1月4日(金) 6:12 Rob Herring <[email protected]>:
>
> On Sun, Dec 23, 2018 at 02:12:44AM +0900, Akinobu Mita wrote:
> > Add device tree binding documentation for the MT9M001 CMOS image sensor.
> >
> > Cc: Rob Herring <[email protected]>
> > Cc: Guennadi Liakhovetski <[email protected]>
> > Cc: Sakari Ailus <[email protected]>
> > Cc: Mauro Carvalho Chehab <[email protected]>
> > Signed-off-by: Akinobu Mita <[email protected]>
> > ---
> > .../devicetree/bindings/media/i2c/mt9m001.txt | 37
> > ++++++++++++++++++++++
> > 1 file changed, 37 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/i2c/mt9m001.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m001.txt
> > b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt
> > new file mode 100644
> > index 0000000..794b787
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt
> > @@ -0,0 +1,37 @@
> > +MT9M001: 1/2-Inch Megapixel Digital Image Sensor
> > +
> > +The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital
> > +image sensor. It is programmable through a simple two-wire serial
> > +interface.
>
> I2C?
Sounds good.
> > +
> > +Required Properties:
> > +
> > +- compatible: shall be "onnn,mt9m001".
> > +- clocks: reference to the master clock into sensor
> > +
> > +Optional Properties:
> > +
> > +- reset-gpios: GPIO handle which is connected to the reset pin of the chip.
> > + Active low.
> > +- standby-gpios: GPIO handle which is connected to the standby pin of the
> > chip.
> > + Active high.
> > +
> > +For further reading on port node refer to
> > +Documentation/devicetree/bindings/media/video-interfaces.txt.
>
> You still need to state how many ports/endpoints and what they are.
I'll write the following description that is copied from
Documentation/devicetree/bindings/media/i2c/mt9m111.txt.
"The device node must contain one 'port' child node with one 'endpoint' child
sub-node for its digital output video port, in accordance with the video
interface bindings defined in:
Documentation/devicetree/bindings/media/video-interfaces.txt"
> > +
> > +Example:
> > +
> > + &i2c1 {
> > + mt9m001@5d {
>
> camera-sensor@5d
OK.
> > + compatible = "onnn,mt9m001";
> > + reg = <0x5d>;
> > + reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
> > + standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
> > + clocks = <&camera_clk>;
> > + port {
> > + mt9m001_out: endpoint {
> > + remote-endpoint = <&vcap_in>;
> > + };
> > + };
> > + };
> > + };
> > --
> > 2.7.4
> >
