Typo in subject: stlye -> style.
Regards,
Hans
On 8/15/19 1:57 PM, Marco Felsch wrote:
> Use underlines to highlight optional and required properties. This is
> quite common for all bindings. Align descriptions and start sentence
> with uppercase letter. Also reword the usage of the required
> endpoint properties for the output port in case BT.656 should be used.
>
> Signed-off-by: Marco Felsch <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> ---
> .../devicetree/bindings/media/i2c/tvp5150.txt | 30 +++++++++++--------
> 1 file changed, 17 insertions(+), 13 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> index 28b64ad149ef..cc98b38c7e73 100644
> --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> @@ -5,12 +5,14 @@ The TVP5150 and TVP5151 are video decoders that convert
> baseband NTSC and PAL
> with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
>
> Required Properties:
> -- compatible: value must be "ti,tvp5150"
> -- reg: I2C slave address
> +====================
> +- compatible: Value must be "ti,tvp5150".
> +- reg: I2C slave address.
>
> Optional Properties:
> -- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
> -- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
> +====================
> +- pdn-gpios: Phandle for the GPIO connected to the PDN pin, if any.
> +- reset-gpios: Phandle for the GPIO connected to the RESETB pin, if
> any.
>
> The device node must contain one 'port' child node per device physical input
> and output port, in accordance with the video interface bindings defined in
> @@ -24,9 +26,8 @@ are numbered as follows
> Y-OUT src 2
>
> The device node must contain at least one sink port and the src port. Each
> input
> -port must be linked to an endpoint defined in
> -Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt.
> The
> -port/connector layout is as follows
> +port must be linked to an endpoint defined in [1]. The port/connector layout
> is
> +as follows
>
> tvp-5150 port@0 (AIP1A)
> endpoint@0 -----------> Comp0-Con port
> @@ -38,14 +39,17 @@ tvp-5150 port@2
> endpoint (video bitstream output at YOUT[0-7] parallel bus)
>
> Required Endpoint Properties for parallel synchronization on output port:
> +=========================================================================
>
> -- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
> -- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
> -- field-even-active: field signal level during the even field data
> - transmission. Must be <0>.
> +- hsync-active: Active state of the HSYNC signal. Must be <1>
> (HIGH).
> +- vsync-active: Active state of the VSYNC signal. Must be <1>
> (HIGH).
> +- field-even-active: Field signal level during the even field data
> + transmission. Must be <0>.
>
> -If none of hsync-active, vsync-active and field-even-active is specified,
> -the endpoint is assumed to use embedded BT.656 synchronization.
> +Note: Do not specify any of these properties if you want to use the embedded
> + BT.656 synchronization.
> +
> +[1]
> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt.
>
> Example - three input sources:
>
>
