The i.MX6DL sabreauto has different numbering on the I2C bus and I2C muxes compared to the i.MX6Q as shown in the kernel log below:
[ 5.159423] imx-media: ipu1_csi0_mux:5 -> ipu1_csi0:0 [ 5.164618] imx-media: ipu1_csi1_mux:5 -> ipu1_csi1:0 [ 5.169953] imx-media: adv7180 4-0021:0 -> ipu1_csi0_mux:4 To avoid confusion, add an entry that shows how to setup the links and configure the pads that are specific to the i.MX6DL sabreauto. Signed-off-by: Fabio Estevam <feste...@gmail.com> --- Changes since v1: - Add a new entry for the mx6dl sabreauto Documentation/media/v4l-drivers/imx.rst | 57 +++++++++++++++++++++++++ 1 file changed, 57 insertions(+) diff --git a/Documentation/media/v4l-drivers/imx.rst b/Documentation/media/v4l-drivers/imx.rst index 36e8d1226ac6..6a9dad8b050b 100644 --- a/Documentation/media/v4l-drivers/imx.rst +++ b/Documentation/media/v4l-drivers/imx.rst @@ -572,6 +572,63 @@ supported YUV or RGB pixelformat on the capture device node. This platform accepts Composite Video analog inputs to the ADV7180 on Ain1 (connector J42). +i.MX6DL SabreAuto with ADV7180 decoder +-------------------------------------- + +On the i.MX6DL SabreAuto, an on-board ADV7180 SD decoder is connected to the +parallel bus input on the internal video mux to IPU1 CSI0. + +The following example configures a pipeline to capture from the ADV7180 +video decoder, assuming NTSC 720x480 input signals, using simple +interweave (unconverted and without motion compensation). The adv7180 +must output sequential or alternating fields (field type 'seq-bt' for +NTSC, or 'alternate'): + +.. code-block:: none + + # Setup links + media-ctl -l "'adv7180 4-0021':0 -> 'ipu1_csi0_mux':4[1]" + media-ctl -l "'ipu1_csi0_mux':5 -> 'ipu1_csi0':0[1]" + media-ctl -l "'ipu1_csi0':2 -> 'ipu1_csi0 capture':0[1]" + # Configure pads + media-ctl -V "'adv7180 4-0021':0 [fmt:UYVY2X8/720x480 field:seq-bt]" + media-ctl -V "'ipu1_csi0_mux':5 [fmt:UYVY2X8/720x480]" + media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/720x480]" + # Configure "ipu1_csi0 capture" interface (assumed at /dev/video4) + v4l2-ctl -d4 --set-fmt-video=field=interlaced_bt + +Streaming can then begin on /dev/video4. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video4. + +This example configures a pipeline to capture from the ADV7180 +video decoder, assuming PAL 720x576 input signals, with Motion +Compensated de-interlacing. The adv7180 must output sequential or +alternating fields (field type 'seq-tb' for PAL, or 'alternate'). + +.. code-block:: none + + # Setup links + media-ctl -l "'adv7180 4-0021':0 -> 'ipu1_csi0_mux':4[1]" + media-ctl -l "'ipu1_csi0_mux':5 -> 'ipu1_csi0':0[1]" + media-ctl -l "'ipu1_csi0':1 -> 'ipu1_vdic':0[1]" + media-ctl -l "'ipu1_vdic':2 -> 'ipu1_ic_prp':0[1]" + media-ctl -l "'ipu1_ic_prp':2 -> 'ipu1_ic_prpvf':0[1]" + media-ctl -l "'ipu1_ic_prpvf':1 -> 'ipu1_ic_prpvf capture':0[1]" + # Configure pads + media-ctl -V "'adv7180 3-0021':0 [fmt:UYVY2X8/720x576 field:seq-tb]" + media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x576]" + media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x576]" + media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]" + media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]" + media-ctl -V "'ipu1_ic_prpvf':1 [fmt:AYUV32/720x576 field:none]" + +Streaming can then begin on the capture device node at +"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any +supported YUV or RGB pixelformat on the capture device node. + +This platform accepts Composite Video analog inputs to the ADV7180 on +Ain1 (connector J42). + SabreSD with MIPI CSI-2 OV5640 ------------------------------ -- 2.17.1
