HI This is my second attempt on Avermedia A188. The hardware on this card is:
1x Philips SAA7160 pci-e bridge 2x NXP SAA7136 multistandard 10-bit A/V decoder 2x Afatech AF9013S demodulator 2x NXP TDA18271 silicon tuner ic (digital/analog) I've written af9013 frontend attach code but I'm having problems with loading firmware. If someone can scan the card on window$ and see what the driver does, are there some gpios that turn on the frontend would be nice (maybe also extract correct firmware) What I did ----------- started from saa716x tree hg clone http://www.jusst.de/hg/saa716x/ and added the af9013 frontend. It compiles fine, loads af9013 module and requests firmware but it won't load Firmware was downloaded from http://www.otit.fi/~crope/v4l-dvb/af9015/dvb-fe-af9013.fw Also tried another firmware for af9015 usb sticks In the code I made a loop to try i2c addresses from 0x00-0x7f for af9013 but so far not found the correct one The patch avermedia-005.diff --------- diff -pur saa716x.orig/linux/drivers/media/common/saa716x/saa716x_hybrid.c saa716x/linux/drivers/media/common/saa716x/saa716x_hybrid.c --- saa716x.orig/linux/drivers/media/common/saa716x/saa716x_hybrid.c 2010-06-20 13:24:18.000000000 +0200 +++ saa716x/linux/drivers/media/common/saa716x/saa716x_hybrid.c 2010-08-10 23:34:42.901211071 +0200 @@ -35,6 +35,9 @@ #include "zl10353.h" #include "mb86a16.h" #include "tda1004x.h" +#include "af9013.h" +#include "tda18271.h" + unsigned int verbose; module_param(verbose, int, 0644); @@ -540,6 +543,82 @@ static struct saa716x_config saa716x_ave .i2c_rate = SAA716x_I2C_RATE_100, }; +#define SAA716x_MODEL_AVERMEDIA_A188 "Avermedia AVerTV Duo Hybrid PCI-E II A188" +#define SAA716x_DEV_AVERMEDIA_A188 "2x DVB-T + 2x Analaog" + +static int load_config_avera188(struct saa716x_dev *saa716x) +{ + int ret = 0; + return ret; +} + +/* probably af9013 is used in parallel mode +** common demod_address are 0x38 and 0x3a +** tuner is nxp tda18271 +*/ +struct af9013_config avera188_af9013_config = { + .demod_address = 0x38, + .output_mode = AF9013_OUTPUT_MODE_PARALLEL, + .api_version = { 0, 1, 9, 0 }, + .gpio[0] = AF9013_GPIO_HI, + .gpio[3] = AF9013_GPIO_TUNER_ON, + +/* + .demod_address = 0x3a, + .output_mode = AF9013_OUTPUT_MODE_SERIAL, + .api_version = { 0, 1, 9, 0 }, + .gpio[0] = AF9013_GPIO_TUNER_ON, + .gpio[1] = AF9013_GPIO_LO, +*/ +}; + + +static int saa716x_avera188_frontend_attach(struct saa716x_adapter *adapter, int count) +{ + struct saa716x_dev *saa716x = adapter->saa716x; + struct saa716x_i2c *i2c = &saa716x->i2c[count]; + int i; + + if (count == 0) { + dprintk(SAA716x_DEBUG, 1, "Adapter (%d) SAA716x frontend Init", count); + dprintk(SAA716x_DEBUG, 1, "Adapter (%d) Device ID=%02x", count, saa716x->pdev->subsystem_device); + dprintk(SAA716x_ERROR, 1, "Adapter (%d) Power ON", count); + saa716x_gpio_write(saa716x, GPIO_14, 1); + msleep(100); + + for(i = 0; i < 1; i++) + { /* try all addresses in a loop */ + /* avera188_af9013_config.demod_address = i; */ + + printk("Trying af9013 frontend on I2C address 0x%02x", avera188_af9013_config.demod_address); + adapter->fe = af9013_attach(&avera188_af9013_config, &i2c->i2c_adapter); + if (adapter->fe == NULL) { + dprintk(SAA716x_ERROR, 1, "Frontend attach failed"); + /* return -ENODEV; */ + } else { + dprintk(SAA716x_ERROR, 1, "Done!"); + return 0; + } + } + return -ENODEV; + + } + + return 0; +} + +static struct saa716x_config saa716x_avera188_config = { + .model_name = SAA716x_MODEL_AVERMEDIA_A188, + .dev_type = SAA716x_DEV_AVERMEDIA_A188, + .boot_mode = SAA716x_EXT_BOOT, + .load_config = &load_config_avera188, + .adapters = 1, + .frontend_attach = saa716x_avera188_frontend_attach, + .irq_handler = saa716x_hybrid_pci_irq, + .i2c_rate = SAA716x_I2C_RATE_100, +}; + + static struct pci_device_id saa716x_hybrid_pci_table[] = { MAKE_ENTRY(TWINHAN_TECHNOLOGIES, TWINHAN_VP_6090, SAA7162, &saa716x_vp6090_config), @@ -547,6 +626,7 @@ static struct pci_device_id saa716x_hybr MAKE_ENTRY(NXP_REFERENCE_BOARD, PCI_ANY_ID, SAA7160, &saa716x_nemo_config), MAKE_ENTRY(AVERMEDIA, AVERMEDIA_HC82, SAA7160, &saa716x_averhc82_config), MAKE_ENTRY(AVERMEDIA, AVERMEDIA_H788, SAA7160, &saa716x_averh788_config), + MAKE_ENTRY(AVERMEDIA, AVERMEDIA_A188, SAA7160, &saa716x_avera188_config), { } }; MODULE_DEVICE_TABLE(pci, saa716x_hybrid_pci_table); Only in saa716x/linux/drivers/media/common/saa716x: saa716x_hybrid.c~ diff -pur saa716x.orig/linux/drivers/media/common/saa716x/saa716x_hybrid.h saa716x/linux/drivers/media/common/saa716x/saa716x_hybrid.h --- saa716x.orig/linux/drivers/media/common/saa716x/saa716x_hybrid.h 2010-06-20 13:24:18.000000000 +0200 +++ saa716x/linux/drivers/media/common/saa716x/saa716x_hybrid.h 2010-08-10 21:02:40.587592396 +0200 @@ -7,5 +7,6 @@ #define TWINHAN_VP_6090 0x0027 #define AVERMEDIA_HC82 0x2355 #define AVERMEDIA_H788 0x1455 +#define AVERMEDIA_A188 0x1855 #endif /* __SAA716x_HYBRID_H */ Only in saa716x/linux/drivers/media/dvb/frontends: af9013.c~ -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
