Hi Guennadi, On 09/17/2011 02:34 PM, Guennadi Liakhovetski wrote: > On Sat, 17 Sep 2011, Sylwester Nawrocki wrote: > >> Hi Laurent, >> >> thanks for your comments. >> >> On 09/17/2011 12:54 PM, Laurent Pinchart wrote: >>> Hi Sylwester, >>> >>> On Friday 16 September 2011 19:28:42 Sylwester Nawrocki wrote: >>>> HREF is a signal indicating valid data during single line transmission. >>>> Add corresponding flags for this signal to the set of mediabus signal >>>> polarity flags. >>> >>> So that's a data valid signal that gates the pixel data ? The OMAP3 ISP has >>> a >> >> Yes, it's "horizontal window reference" signal, it's well described in this >> datasheet: >> http://www.morninghan.com/pdf/OV2640FSL_DS_(1_3).pdf >> >> AFAICS there can be also its vertical counterpart - VREF. >> >> Many devices seem to use this terminology. However, I realize, not all, as >> you're >> pointing out. So perhaps it's time for some naming contest now.. :-) > > Hi > > No objections in principle, just one question though: can these signals > actually be used simultaneously with respective *SYNC signals or only as > an alternative? If the latter, maybe we could reuse same names by just > making them more generic?
That's actually a good question. In my use cases only HREF is used as horizontal synchronization signal, i.e. physical bus interface has this signals: ->| PCLK ->| VSYNC ->| HREF ->| DATA[0:7] ->| FIELD For interlaced mode FIELD can be connected to the horizontal synchronization signal. For this case there is InvPolHSYNC bit in the host interface registers to indicate the polarity. There are 5 bits actually: InvPolPCLK InvPolVSYNC (vertical sychronization) InvPolHREF (horizontal synchronization) InvPolHSYNC (for interlaced mode only, FIELD port = horizontal sync. signal) InvPolFIELD (interlaced mode, FIELD port = FIELD signal) IMHO keeping different names for synchronization and 'data valid' signals is more clear. > > Thanks > Guennadi > >>> similar signal called WEN, and I've seen other chips using DVAL. Your patch >>> looks good to me, except maybe for the signal name that could be made a bit >>> more explicit (I'm not sure what most chips use though). >> >> I'm pretty OK with HREF/VREF. But I'm open to any better suggestions. >> >> Maybe >> >> V4L2_MBUS_LINE_VALID_ACTIVE_HIGH >> V4L2_MBUS_LINE_VALID_ACTIVE_LOW >> >> V4L2_MBUS_FRAME_VALID_ACTIVE_HIGH >> V4L2_MBUS_FRAME_VALID_ACTIVE_LOW >> >> ? >> Some of Aptina sensor datasheets describes those signals as >> LINE_VALID/FRAME_VALID, >> (www.aptina.com/assets/downloadDocument.do?id=76). >> >>> >>>> Signed-off-by: Sylwester Nawrocki<s.nawro...@samsung.com> >>>> Signed-off-by: Kyungmin Park<kyungmin.p...@samsung.com> >>>> --- >>>> include/media/v4l2-mediabus.h | 14 ++++++++------ >>>> 1 files changed, 8 insertions(+), 6 deletions(-) >>>> >>>> diff --git a/include/media/v4l2-mediabus.h b/include/media/v4l2-mediabus.h >>>> index 6114007..41d8771 100644 >>>> --- a/include/media/v4l2-mediabus.h >>>> +++ b/include/media/v4l2-mediabus.h >>>> @@ -26,12 +26,14 @@ >>>> /* Note: in BT.656 mode HSYNC and VSYNC are unused */ >> >> I've forgotten to update this: >> >> /* Note: in BT.656 mode HSYNC, HREF and VSYNC are unused */ >> >>>> #define V4L2_MBUS_HSYNC_ACTIVE_HIGH (1<< 2) >>>> #define V4L2_MBUS_HSYNC_ACTIVE_LOW (1<< 3) >>>> -#define V4L2_MBUS_VSYNC_ACTIVE_HIGH (1<< 4) >>>> -#define V4L2_MBUS_VSYNC_ACTIVE_LOW (1<< 5) >>>> -#define V4L2_MBUS_PCLK_SAMPLE_RISING (1<< 6) >>>> -#define V4L2_MBUS_PCLK_SAMPLE_FALLING (1<< 7) >>>> -#define V4L2_MBUS_DATA_ACTIVE_HIGH (1<< 8) >>>> -#define V4L2_MBUS_DATA_ACTIVE_LOW (1<< 9) >>>> +#define V4L2_MBUS_HREF_ACTIVE_HIGH (1<< 4) >>>> +#define V4L2_MBUS_HREF_ACTIVE_LOW (1<< 5) >>>> +#define V4L2_MBUS_VSYNC_ACTIVE_HIGH (1<< 6) >>>> +#define V4L2_MBUS_VSYNC_ACTIVE_LOW (1<< 7) >>>> +#define V4L2_MBUS_PCLK_SAMPLE_RISING (1<< 8) >>>> +#define V4L2_MBUS_PCLK_SAMPLE_FALLING (1<< 9) >>>> +#define V4L2_MBUS_DATA_ACTIVE_HIGH (1<< 10) >>>> +#define V4L2_MBUS_DATA_ACTIVE_LOW (1<< 11) -- Regards, Sylwester -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
