On 06/27/2012 07:21 AM, Thomas Mair wrote: > On 26.06.2012 19:17, poma wrote: >> On 05/28/2012 04:48 PM, Thomas Mair wrote: >>> On 28.05.2012 08:58, Thomas Mair wrote: >>>> On 26.05.2012 04:47, poma wrote: >>>>> On 05/20/2012 11:12 PM, Thomas Mair wrote: >>>>>> On 20.05.2012 22:08, Antti Palosaari wrote: >>>>>>> On 20.05.2012 20:04, poma wrote: >>>>>>>> After hard/cold boot: >>>>>>> >>>>>>>> DVB: register adapter0/net0 @ minor: 2 (0x02) >>>>>>>> rtl2832u_frontend_attach: >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> rtl28xxu_ctrl_msg: failed=-32 >>>>>>>> No compatible tuner found >>>>>>> >>>>>>> These errors are coming from tuner probe. As it still goes to probing >>>>>>> and did not jump out earlier when gate is opened it means that demod is >>>>>>> answering commands but tuner are not. >>>>>>> >>>>>>> My guess is that tuner is still on the reset or not powered at all. It >>>>>>> is almost 100% sure error is wrong tuner GPIO. >>>>>> >>>>>> There is an issue with GPIO, as FC0012 tuner callback will set >>>>>> the value of one of the GPIO outputs. However fixing that, will >>>>>> not resolve the issue. So I need to debug the problem further. >>>>>> >>>>> True. Whatever a value is changed - 'rtl2832u_power_ctrl', it brakes >>>>> even more. >>>>> Precisely, what breaks a tuner on next soft [re]boot are apps/utils >>>>> which engage tzap/scan[dvb]. >>>>> >>>> >>>> To reproduce the bug it is not necessary to reboot the machine. Simply >>>> unload and load of the dvb_usb_rtl28xxu module will lead to the same >>>> situation. >>>> >>>> I suspect, that when power is turned off, the tuner power is not >>>> switched on correctly. The mistake is not related to the OUTPUT_VAL >>>> registers but probably to the OUTPUT_DIR or OUTPUT_EN registers. >>>> >>>> What makes me wonder is if no tuning operation is performed before >>>> reboot, the driver does work correctly after that, as poma already >>>> noticed. >>>> >>>> I have some spare time today and will investigate the problem further. >>>> >>> >>> I tried a few things regarding the problem today and could find out a >>> few more details, but could not resolve the issue. >>> >>> The GPIO pin configuration for the devices with the fc0012 (and probably >>> also with the fc0013) tuner is the following: >>> >>> GPIO0: demod power >>> GPIO3: tuner power? (the realtek driver puts this to 1 and never touches it >>> again) >>> GPIO4: tuner power? (maybe antenna power?) >>> GPIO5: tuner reset >>> GPIO6: UHF/VHF band selection >>> >>> All of these GPIOs are configured as output. When the device is plugged in >>> the tuner is powered up correctly, but I am not able to power it up when >>> a reboot is performed. What I tried was the following: >>> >>> - on rtl28xxu_power_ctrl off: >>> - GPIO4 = 1 (off) >>> - GPIO5 = 0 >>> - GPIO6 = 0 (default state) >>> >>> - on rtl28xxu_power_ctrl on: >>> - GPIO3 = 1 >>> - GPIO4 = 0 (on) >>> - GPIO5 = 0 >>> - GPIO6 = 0 (default state) >>> >>> - on rtl2832_frontend_attach: >>> - GPIO5 = 1 >>> - GPIO5 = 0 >>> >>> This sequence should ensure that the tuner is powered on when the frontend >>> is attached, and a tuner reset is being performed before the tuner is >>> probed. >>> However this sequence fails the same way as it did before. I tried to add >>> timeouts to be sure that the tuner is not probed while it is reset but that >>> did not help either. >>> >>> Right now I really don't know where I should look for the solution of >>> the problem. It seems that the tuner reset does not have any effect on the >>> tuner whatsoever. >>> >>> Is there anybody who could look at the code, or maybe knows what could be >>> the cause of the problem? I suspect I am just too blind to see my own >>> mistakes. >>> >>> Regards >>> Thomas >>> >> >> Cheers Thomas, Hans-Frieder, Antti, Mauro! >> Hans-Frieder, are you having the same issue with fc0011&af9035? >> Antti, no tricks up your sleeve? >> Senhor Mauro, is rtl2832 demod going to be merged? >> >> regards, >> poma >> > Hi all, > > I will try to solve the issue as soon as I have some spare time. In the > meantime I > asked Realtek if they knew of any problems with the hardware, and I got a GPIO > list which might help me to solve the problem. > > Regrads > Thomas >
This is correspondent code by dbasden - fc0012 for rtl-sdr GPIOs https://gist.github.com/2171926#120 David, can you help with this tuner issue? http://git.linuxtv.org/anttip/media_tree.git/blob/3efd26330fda97e06279cbca170ae4a0dee53220:/drivers/media/dvb/dvb-usb/rtl28xxu.c#l898 Cheers, poma -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
