From: Guennadi Liakhovetski <g.liakhovet...@gmx.de>
This patch adds a document, describing common V4L2 device tree bindings.
Co-authored-by: Sylwester Nawrocki <s.nawro...@samsung.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovet...@gmx.de>
---
Documentation/devicetree/bindings/media/v4l2.txt | 162 ++++++++++++++++++++++
1 file changed, 162 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/v4l2.txt
diff --git a/Documentation/devicetree/bindings/media/v4l2.txt
b/Documentation/devicetree/bindings/media/v4l2.txt
new file mode 100644
index 0000000..b8b3f41
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/v4l2.txt
@@ -0,0 +1,162 @@
+Video4Linux Version 2 (V4L2)
+
+General concept
+---------------
+
+Video pipelines consist of external devices, e.g. camera sensors, controlled
+over an I2C, SPI or UART bus, and SoC internal IP blocks, including video DMA
+engines and video data processors.
+
+SoC internal blocks are described by DT nodes, placed similarly to other SoC
+blocks. External devices are represented as child nodes of their respective bus
+controller nodes, e.g. I2C.
+
+Data interfaces on all video devices are described by "port" child DT nodes.
+Configuration of a port depends on other devices participating in the data
+transfer and is described by "link" DT nodes, specified as children of the
+"port" nodes:
+
+/foo {
+ port@0 {
+ link@0 { ... };
+ link@1 { ... };
+ };
+ port@1 { ... };
+};
+
+If a port can be configured to work with more than one other device on the same
+bus, a "link" child DT node must be provided for each of them. If more than one
+port is present on a device or more than one link is connected to a port, a
+common scheme, using "#address-cells," "#size-cells" and "reg" properties is
+used.
+
+Optional link properties:
+- remote: phandle to the other endpoint link DT node.
+- slave-mode: a boolean property, run the link in slave mode. Default is master
+ mode.
+- data-shift: on parallel data busses, if data-width is used to specify the
+ number of data lines, data-shift can be used to specify which data lines are
+ used, e.g. "data-width=<10>; data-shift=<2>;" means, that lines 9:2 are used.
+- hsync-active: 1 or 0 for active-high or -low HSYNC signal polarity
+ respectively.
+- vsync-active: ditto for VSYNC. Note, that if HSYNC and VSYNC polarities are
+ not specified, embedded synchronisation may be required, where supported.
+- data-active: similar to HSYNC and VSYNC specifies data line polarity.
+- field-even-active: field signal level during the even field data
transmission.
+- pclk-sample: rising (1) or falling (0) edge to sample the pixel clock pin.
+- data-lanes: array of serial, e.g. MIPI CSI-2, data hardware lane numbers in
+ the ascending order, beginning with logical lane 0.
+- clock-lanes: hardware lane number, used for the clock lane.
+- clock-noncontinuous: a boolean property to allow MIPI CSI-2 non-continuous
+ clock mode.
+
+Example:
+
+ ceu0: ceu@0xfe910000 {
+ compatible = "renesas,sh-mobile-ceu";
+ reg = <0xfe910000 0xa0>;
+ interrupts = <0x880>;
+
+ mclk: master_clock {
+ compatible = "renesas,ceu-clock";
+ #clock-cells = <1>;
+ clock-frequency = <50000000>; /* max clock frequency
*/
+ clock-output-names = "mclk";
+ };
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ceu0_1: link@1 {
+ reg = <1>; /* local link # */
+ remote = <&ov772x_1_1>; /* remote phandle */
+ bus-width = <8>; /* used data lines */
+ data-shift = <0>; /* lines 7:0 are used */
+
+ /* If [hv]sync-active are missing, embedded
bt.605 sync is used */
+ hsync-active = <1>; /* active high */
+ vsync-active = <1>; /* active high */
+ data-active = <1>; /* active high */
+ pclk-sample = <1>; /* rising */
+ };
+
+ ceu0_0: link@0 {
+ reg = <0>;
+ remote = <&csi2_2>;
+ immutable;
+ };
+ };
+ };
+
+ i2c0: i2c@0xfff20000 {
+ ...
+ ov772x_1: camera@0x21 {
+ compatible = "omnivision,ov772x";
+ reg = <0x21>;
+ vddio-supply = <®ulator1>;
+ vddcore-supply = <®ulator2>;
+
+ clock-frequency = <20000000>;
+ clocks = <&mclk 0>;
+ clock-names = "xclk";
+
+ port {
+ /* With 1 link per port no need in addresses */
+ ov772x_1_1: link {
+ bus-width = <8>;
+ remote = <&ceu0_1>;
+ hsync-active = <1>;
+ vsync-active = <0>; /* who came up
with an inverter here?... */
+ data-active = <1>;
+ pclk-sample = <1>;
+ };
+ };
+ };
+
+ imx074: camera@0x1a {
+ compatible = "sony,imx074";
+ reg = <0x1a>;
+ vddio-supply = <®ulator1>;
+ vddcore-supply = <®ulator2>;
+
+ clock-frequency = <30000000>; /* shared clock with
ov772x_1 */
+ clocks = <&mclk 0>;
+ clock-names = "sysclk"; /* assuming this is the
name in the datasheet */
+
+ port {
+ imx074_1: link {
+ clock-lanes = <0>;
+ data-lanes = <1>, <2>;
+ remote = <&csi2_1>;
+ };
+ };
+ };
+ };
+
+ csi2: csi2@0xffc90000 {
+ compatible = "renesas,sh-mobile-csi2";
+ reg = <0xffc90000 0x1000>;
+ interrupts = <0x17a0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ compatible = "renesas,csi2c"; /* one of CSI2I and
CSI2C */
+ reg = <1>; /* CSI-2 PHY #1 of 2:
PHY_S, PHY_M has port address 0, is unused */
+
+ csi2_1: link {
+ clock-lanes = <0>;
+ data-lanes = <2>, <1>;
+ remote = <&imx074_1>;
+ };
+ };
+ port@2 {
+ reg = <2>; /* port 2: link to the
CEU */
+
+ csi2_2: link {
+ immutable;
+ remote = <&ceu0_0>;
+ };
+ };
+ };
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
