On Fri, 20 Mar 2015, Jacek Anaszewski wrote: > This patch adds device tree binding documentation for > the flash cell of the Maxim max77693 multifunctional device. > > Signed-off-by: Jacek Anaszewski <j.anaszew...@samsung.com> > Signed-off-by: Andrzej Hajda <a.ha...@samsung.com> > Acked-by: Kyungmin Park <kyungmin.p...@samsung.com> > Cc: Lee Jones <lee.jo...@linaro.org> > Cc: Chanwoo Choi <cw00.c...@samsung.com> > Cc: Bryan Wu <coolo...@gmail.com> > Cc: Richard Purdie <rpur...@rpsys.net> > --- > Documentation/devicetree/bindings/mfd/max77693.txt | 61 > ++++++++++++++++++++ > 1 file changed, 61 insertions(+)
Bryan and/or one of the DT folks really need to Ack this. > diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt > b/Documentation/devicetree/bindings/mfd/max77693.txt > index 38e6440..15c546e 100644 > --- a/Documentation/devicetree/bindings/mfd/max77693.txt > +++ b/Documentation/devicetree/bindings/mfd/max77693.txt > @@ -76,7 +76,53 @@ Optional properties: > Valid values: 4300000, 4700000, 4800000, 4900000 > Default: 4300000 > > +- led : the LED submodule device node > + > +There are two LED outputs available - FLED1 and FLED2. Each of them can > +control a separate LED or they can be connected together to double > +the maximum current for a single connected LED. One LED is represented > +by one child node. > + > +Required properties: > +- compatible : Must be "maxim,max77693-led". > + > +Optional properties: > +- maxim,trigger-type : Flash trigger type. > + Possible trigger types: > + LEDS_TRIG_TYPE_EDGE (0) - Rising edge of the signal triggers > + the flash, > + LEDS_TRIG_TYPE_LEVEL (1) - Strobe pulse length controls duration > + of the flash. > +- maxim,boost-mode : > + In boost mode the device can produce up to 1.2A of total current > + on both outputs. The maximum current on each output is reduced > + to 625mA then. If not enabled explicitly, boost setting defaults to > + LEDS_BOOST_FIXED in case both current sources are used. > + Possible values: > + LEDS_BOOST_OFF (0) - no boost, > + LEDS_BOOST_ADAPTIVE (1) - adaptive mode, > + LEDS_BOOST_FIXED (2) - fixed mode. > +- maxim,boost-mvout : Output voltage of the boost module in millivolts. > +- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired > + if chip estimates that system voltage could drop below this level due > + to flash power consumption. > + > +Required properties of the LED child node: > +- led-sources : see Documentation/devicetree/bindings/leds/common.txt; > + device current output identifiers: 0 - FLED1, 1 - FLED2 > + > +Optional properties of the LED child node: > +- label : see Documentation/devicetree/bindings/leds/common.txt > +- max-microamp : see Documentation/devicetree/bindings/leds/common.txt > + Range: 15625 - 250000 > +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt > + Range: 15625 - 1000000 > +- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt > + Range: 62500 - 1000000 > + > Example: > +#include <dt-bindings/leds/common.h> > + > max77693@66 { > compatible = "maxim,max77693"; > reg = <0x66>; > @@ -117,5 +163,20 @@ Example: > maxim,thermal-regulation-celsius = <75>; > maxim,battery-overcurrent-microamp = <3000000>; > maxim,charge-input-threshold-microvolt = <4300000>; > + > + led { > + compatible = "maxim,max77693-led"; > + maxim,trigger-type = <LEDS_TRIG_TYPE_LEVEL>; > + maxim,boost-mode = <LEDS_BOOST_FIXED>; > + maxim,boost-mvout = <5000>; > + maxim,mvsys-min = <2400>; > + > + camera_flash: flash-led { > + label = "max77693-flash"; > + led-sources = <0>, <1>; > + max-microamp = <500000>; > + flash-max-microamp = <1250000>; > + flash-timeout-us = <1000000>; > + }; > }; > }; -- Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html