On Wed, Apr 18, 2012 at 6:24 PM, Jaehoon Chung <jh80.ch...@samsung.com> wrote:
> On 04/18/2012 05:42 PM, S, Venkatraman wrote:
>
>> On Wed, Apr 18, 2012 at 1:53 PM, Namjae Jeon <linkinj...@gmail.com> wrote:
>>> 2012/4/18 S, Venkatraman <svenk...@ti.com>:
>>>> On Wed, Apr 18, 2012 at 10:15 AM, Namjae Jeon <linkinj...@gmail.com> wrote:
>>>>> 2012/4/18 Jaehoon Chung <jh80.ch...@samsung.com>:
>>>>>> On 04/18/2012 09:20 AM, Namjae Jeon wrote:
>>>>>>
>>>>>>> 2012/4/17 Venkatraman S <svenk...@ti.com>:
>>>>>>>> mmc_execute_hpi should send the HPI command only
>>>>>>>> once, only if the card is in PRG state.
>>>>>>>>
>>>>>>>> According to eMMC spec, the command's completion time is
>>>>>>>> not dependent on OUT_OF_INTERRUPT_TIME. Only the transition
>>>>>>>> out of PRG STATE is guarded by OUT_OF_INTERRUPT_TIME - which is
>>>>>>>> defined to begin at the end of sending the command itself.
>>>>>>> Hi. Venkatraman.
>>>>>>> I can not find this words. " the command's completion time is not
>>>>>>> dependent on OUT_OF_INTERRUPT_TIME" .
>>>>>>> Would you inform me which page and which part you checked in
>>>>>>> specification ?
>>>>>>
>>>>>> Well, i know that timeout value is used the OUT_OF_INTERRUPT_TIME, when
>>>>>> interrupted by HPI.
>>>>>> It's my misunderstanding?
>>>>> I agree, I also understand with you. But we should hear Venkatraman's
>>>>> opinion from next reply.
>>>>> see the spec.
>>>>
>>>> That particular line was explicit, *emphasis* mine..
>>>> In Section 6.8.2 "OUT_OF_INTERRUPT_TIME defines the maximum time
>>>> between the *end* bit of CMD12/13, arg[0]=1 to the DAT0 release of the
>>>> device."
>>>>
>>>> Which essentially means the timer should start after the HPI command
>>>> has been exchanged, and should normally end when the DAT0 line is
>>>> released (in other words, move out of PRG state).
>>>> You can see the same definition in Section 7.4.33
>>>>
>>>> The definition in 6.6.23, is partly confusing, for one it uses
>>>> OUT_OF_INTERRUPT_BUSY_TIME and not OUT_OF_INTERRUPT_TIME, and other,
>>>> it refers to the command being *interrupted by* HPI, not the HPI
>>>> command itself.
>>>>
>>>> Let me know if this explains it a bit better.
>>>>
>>>> Best regards,
>>>> Venkat.
>>> Hi. Venkat.
>>> You're right. OUT_OF_INTERRUPT_TIME is range between Busy line(Data0)
>>> released by device and end bit of CMD 12,13.
>>> and I would like you change some code in this patch.
>>> I think that break is better than goto. because it is not duplicated loop.
>>> + if (!err && R1_CURRENT_STATE(status) == R1_STATE_TRAN)
>>> + goto out;
>>>
>>> you don't need to initialize cmd_timeout_ms value. because you can see
>>> struct mmc_command cmd = {0}; code.
>>> + cmd.cmd_timeout_ms = 0;
>>>
>>> Thanks.
>>>
>>
>> Great - thanks for your review and feedback. I'll post a new patch
>> after making the changes you
>
> Thanks for your explanation. it makes sense.
> If you resend the patch, i will test with your patch.
>
I've just sent it. Let me know if you require more details.
> Best Regards,
> Jaehoon Chung
>
>> requested.
>> Regards,
>> Venkat.
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>> the body of a message to majord...@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
