On Fri, 2013-08-09 at 11:54 +0900, Jaehoon Chung wrote:
> Hi Dinh
>
> On 08/09/2013 07:55 AM, dingu...@altera.com wrote:
> > From: Dinh Nguyen <dingu...@altera.com>
> >
> > Remove the "samsung" in "samsung,dw-mshc-ciu-div",
> > "samsung,dw-mshc-sdr-timing",
> > and "samsung,dw-mshc-ddr-timing". These characteristics are not applicable
> > to
> > just Samsung platforms, but to any platform that uses the Synopsis SD/MMC
> > IP.
> >
> > Signed-off-by: Dinh Nguyen <dingu...@altera.com>
> > CC: Arnd Bergmann <a...@arndb.de>
> > Cc: Olof Johansson <o...@lixom.net>
> > Cc: Jaehoon Chung <jh80.ch...@samsung.com>
> > Cc: Seungwon Jeon <tgih....@samsung.com>
> > Cc: Rob Herring <rob.herr...@calxeda.com>
> > Cc: Pawel Moll <pawel.m...@arm.com>
> > Cc: Mark Rutland <mark.rutl...@arm.com>
> > Cc: Stephen Warren <swar...@wwwdotorg.org>
> > Cc: Ian Campbell <ian.campb...@citrix.com>
> > Cc: devicet...@vger.kernel.org
> > Cc: linux-mmc@vger.kernel.org
> > CC: linux-arm-ker...@lists.infradead.org
> > ---
> > .../devicetree/bindings/mmc/exynos-dw-mshc.txt | 30
> > --------------------
> > .../devicetree/bindings/mmc/synopsis-dw-mshc.txt | 29
> > +++++++++++++++++++
> > arch/arm/boot/dts/cros5250-common.dtsi | 18 ++++++------
> > arch/arm/boot/dts/exynos4412-odroidx.dts | 6 ++--
> > arch/arm/boot/dts/exynos4412-origen.dts | 6 ++--
> > arch/arm/boot/dts/exynos5250-arndale.dts | 12 ++++----
> > arch/arm/boot/dts/exynos5250-smdk5250.dts | 12 ++++----
> > drivers/mmc/host/dw_mmc-exynos.c | 6 ++--
> > 8 files changed, 59 insertions(+), 60 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> > b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> > index 6d1c098..ddb1d95 100644
> > --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> > +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> > @@ -17,33 +17,6 @@ Required Properties:
> > - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
> > specific extensions.
> >
> > -* samsung,dw-mshc-ciu-div: Specifies the divider value for the card
> > interface
> > - unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
> > - ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
> > -
> > -* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift
> > value
> > - in transmit mode and CIU clock phase shift value in receive mode for
> > single
> > - data rate mode operation. Refer notes below for the order of the cells
> > and the
> > - valid values.
> > -
> > -* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift
> > value
> > - in transmit mode and CIU clock phase shift value in receive mode for
> > double
> > - data rate mode operation. Refer notes below for the order of the cells
> > and the
> > - valid values.
> > -
> > - Notes for the sdr-timing and ddr-timing values:
> > -
> > - The order of the cells should be
> > - - First Cell: CIU clock phase shift value for tx mode.
> > - - Second Cell: CIU clock phase shift value for rx mode.
> > -
> > - Valid values for SDR and DDR CIU clock timing for Exynos5250:
> > - - valid value for tx phase shift and rx phase shift is 0 to 7.
> > - - when CIU clock divider value is set to 3, all possible 8 phase
> > shift
> > - values can be used.
> > - - if CIU clock divider value is 0 (that is divide by 1), both tx and
> > rx
> > - phase shift clocks should be 0.
> > -
> > Required properties for a slot:
> >
> > * gpios: specifies a list of gpios used for command, clock and data bus.
> > The
> > @@ -71,9 +44,6 @@ Example:
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> >
> > slot@0 {
> > reg = <0>;
> > diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> > b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> > index cdcebea..cf85a8c 100644
> > --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> > +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> > @@ -71,6 +71,32 @@ Optional properties:
> > * vmmc-supply: The phandle to the regulator to use for vmmc. If this is
> > specified we'll defer probe until we can find this regulator.
> >
> > +* dw-mshc-ciu-div: Specifies the divider value for the card interface
> > + unit (ciu) clock. The valid range of divider value is 0 to 7.
> > +
> > +* dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
> > + in transmit mode and CIU clock phase shift value in receive mode for
> > single
> > + data rate mode operation. Refer notes below for the order of the cells
> > and the
> > + valid values.
> > +
> > +* dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
> > + in transmit mode and CIU clock phase shift value in receive mode for
> > double
> > + data rate mode operation. Refer notes below for the order of the cells
> > and the
> > + valid values.
> > +
> > + Notes for the sdr-timing and ddr-timing values:
> > +
> > + The order of the cells should be
> > + - First Cell: CIU clock phase shift value for tx mode.
> > + - Second Cell: CIU clock phase shift value for rx mode.
> > +
> > + Valid values for SDR and DDR CIU clock timing for Exynos5250:
> Exynos5250? Maybe It should be mentioned common SoC.
> > + - valid value for tx phase shift and rx phase shift is 0 to 7.
> > + - when CIU clock divider value is set to 3, all possible 8
> > phase shift
> > + values can be used.
> > + - if CIU clock divider value is 0 (that is divide by 1), both
> > tx and rx
> > + phase shift clocks should be 0.
> > +
> > Aliases:
> >
> > - All the MSHC controller nodes should be represented in the aliases node
> > using
> > @@ -99,6 +125,9 @@ board specific portions as listed below.
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > vmmc-supply = <&buck8>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> >
> > slot@0 {
> > reg = <0>;
> > diff --git a/arch/arm/boot/dts/cros5250-common.dtsi
> > b/arch/arm/boot/dts/cros5250-common.dtsi
> > index dc259e8b..93d3c85 100644
> > --- a/arch/arm/boot/dts/cros5250-common.dtsi
> > +++ b/arch/arm/boot/dts/cros5250-common.dtsi
> > @@ -235,9 +235,9 @@
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
> >
> > @@ -256,9 +256,9 @@
> > supports-highspeed;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> >
> > @@ -275,9 +275,9 @@
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > /* See board-specific dts files for pin setup */
> >
> > slot@0 {
> > diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts
> > b/arch/arm/boot/dts/exynos4412-odroidx.dts
> > index 46c678e..e6c3b23 100644
> > --- a/arch/arm/boot/dts/exynos4412-odroidx.dts
> > +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
> > @@ -51,9 +51,9 @@
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> >
> > slot@0 {
> > reg = <0>;
> > diff --git a/arch/arm/boot/dts/exynos4412-origen.dts
> > b/arch/arm/boot/dts/exynos4412-origen.dts
> > index 7993641..b403a57 100644
> > --- a/arch/arm/boot/dts/exynos4412-origen.dts
> > +++ b/arch/arm/boot/dts/exynos4412-origen.dts
> > @@ -122,9 +122,9 @@
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> >
> > slot@0 {
> > reg = <0>;
> > diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts
> > b/arch/arm/boot/dts/exynos5250-arndale.dts
> > index abc7272..72aa743 100644
> > --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> > +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> > @@ -324,9 +324,9 @@
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > vmmc-supply = <&mmc_reg>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
> > @@ -346,9 +346,9 @@
> > supports-highspeed;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > vmmc-supply = <&mmc_reg>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> > diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > b/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > index 49f18c2..220da19 100644
> > --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > @@ -146,9 +146,9 @@
> > broken-cd;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
> >
> > @@ -167,9 +167,9 @@
> > supports-highspeed;
> > fifo-depth = <0x80>;
> > card-detect-delay = <200>;
> > - samsung,dw-mshc-ciu-div = <3>;
> > - samsung,dw-mshc-sdr-timing = <2 3>;
> > - samsung,dw-mshc-ddr-timing = <1 2>;
> > + dw-mshc-ciu-div = <3>;
> > + dw-mshc-sdr-timing = <2 3>;
> > + dw-mshc-ddr-timing = <1 2>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> >
> > diff --git a/drivers/mmc/host/dw_mmc-exynos.c
> > b/drivers/mmc/host/dw_mmc-exynos.c
> > index 866edef..553f3c1 100644
> > --- a/drivers/mmc/host/dw_mmc-exynos.c
> > +++ b/drivers/mmc/host/dw_mmc-exynos.c
> > @@ -131,18 +131,18 @@ static int dw_mci_exynos_parse_dt(struct dw_mci *host)
> > u32 div = 0;
> > int ret;
> >
> > - of_property_read_u32(np, "samsung,dw-mshc-ciu-div", &div);
> > + of_property_read_u32(np, "dw-mshc-ciu-div", &div);
> > priv->ciu_div = div;
> >
> > ret = of_property_read_u32_array(np,
> > - "samsung,dw-mshc-sdr-timing", timing, 2);
> > + "dw-mshc-sdr-timing", timing, 2);
> > if (ret)
> > return ret;
> >
> > priv->sdr_timing = SDMMC_CLKSEL_TIMING(timing[0], timing[1], div);
> >
> > ret = of_property_read_u32_array(np,
> > - "samsung,dw-mshc-ddr-timing", timing, 2);
> > + "dw-mshc-ddr-timing", timing, 2);
> > if (ret)
> > return ret;
> Then we can move functions related with clksel from dw-mmc-exynos.c to
> dw-mmc.c, isn't it?
I think so, but I figure we can agree on some common bindings for the
Exynos and SoCFPGA platforms first?
Thanks,
Dinh
>
> Best Regards,
> Jaehoon Chung
> >
> >
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
