On Fri, 18 Oct 2013 12:59:56 +0530 Balaji T K <balaj...@ti.com> wrote:
> On Friday 18 October 2013 11:50 AM, NeilBrown wrote:
> > On Sat, 5 Oct 2013 13:17:09 +0200 Andreas Fenkart <afenk...@gmail.com>
> > wrote:
> >
> >> The am335x can't detect pending cirq in PM runtime suspend.
> >> This patch reconfigures dat1 as a GPIO before going to suspend.
> >> SDIO interrupts are detected with the GPIO, while in runtime
> >> suspend, standard detection of the module block otherwise.
> >>
> >> Signed-off-by: Andreas Fenkart <afenk...@gmail.com>
> >>
> >> diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> >> b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> >> index 1136e6b..146f3ad 100644
> >> --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> >> +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> >> @@ -21,8 +21,11 @@ ti,non-removable: non-removable slot (like eMMC)
> >> ti,needs-special-reset: Requires a special softreset sequence
> >> ti,needs-special-hs-handling: HSMMC IP needs special setting for
> >> handling High Speed
> >> ti,quirk-swakup-missing: SOC missing the swakeup line, will not detect
> >> -SDIO irq while in suspend. Fallback to polling. Affected chips are
> >> -am335x,
> >> +SDIO irq while in suspend. The workaround is to reconfigure the dat1 line
> >> as a
> >> +GPIO upon suspend. Beyond this option and the GPIO config, you also need
> >> to set
> >> +named pinctrl states "default", "active" and "idle ", see example below.
> >> The
> >> +MMC driver will then then toggle between default and idle during the
> >> runtime
> >> +Affected chips are am335x,
> >>
> >> ------
> >> | PRCM |
> >> @@ -49,3 +52,24 @@ Example:
> >> vmmc-supply = <&vmmc>; /* phandle to regulator node */
> >> ti,non-removable;
> >> };
> >> +
> >> +[am335x with with gpio for sdio irq]
> >> +
> >> + mmc1_cirq_pin: pinmux_cirq_pin {
> >> + pinctrl-single,pins = <
> >> + 0x0f8 0x3f /* MMC0_DAT1 as GPIO2_28 */
> >> + >;
> >> + };
> >> +
> >> + mmc1: mmc@48060000 {
> >> + ti,non-removable;
> >> + bus-width = <4>;
> >> + vmmc-supply = <&ldo2_reg>;
> >> + vmmc_aux-supply = <&vmmc>;
> >> + ti,quirk-swakeup-missing;
> >> + pinctrl-names = "default", "active", "idle";
> >> + pinctrl-0 = <&mmc1_pins>;
> >> + pinctrl-1 = <&mmc1_pins>;
> >> + pinctrl-2 = <&mmc1_cirq_pin>;
> >> + ti,cirq-gpio = <&gpio3 28 0>;
> >> + };
> >
> >
> > hi,
> > I've been trying to get SD irq to work on my OMAP3 DM3730.
> > I seems to need the magic to catch interrupts while FCLK is off, as
> > the only way I can get it to work at the moment is to keep FCLK on.
> >
> > I discovered your patch and tried it out, but it doesn't seem to work for
> > me.
> >
> > I have a Libertas WIFI chip attached to the second mmc (which is sometimes
> > called mmc1, and sometimes mmc2 - very confusing!).
> > I added:
> > mmc2_cirq_pin: pinmux_cirq_pin {
> > pinctrl-single,pins = <
> > 0x012e (PIN_INPUT_PULLUP | MUX_MODE4) /* MMC2_DAT1 as
> > GPIO5_5 */
> > >;
> > };
> >
> > and
> >
> > &mmc2 {
> > ti,quirk-swakeup-missing;
> > pinctrl-names = "default", "active", "idle";
> > pinctrl-0 = <&mmc2_pins>;
> > pinctrl-1 = <&mmc2_pins>;
> > pinctrl-2 = <&mmc2_cirq_pin>;
> > ti,cirq-gpio = <&gpio5 5 0>; /* GPIO133 = 128+5 */
> > };
> >
> > to my dts file but it doesn't make any apparent difference.
> >
> > Any idea what I might be doing wrong?
> > (the base kernel I am applying patches to is from 8th Oct,
> > commit 0e7a3ed04f0cd4311096d691888f88569310ee6c)
> >
> > BTW,
> > - with the default polling, I get about 1Mb/sec with iperf
> > - with sd-irq enabled and FCLK kept on the whole time, I get 4Mb/sec
> > - with sd-irq enable, FCLK kept on, and the 5ms polling also
> > running, I get over 5Mb/sec!
> > Still much less than the 40Mb/sec that I would like to get...
> >
> (removing svenk...@ti.com)
>
> Hi,
>
> Can you check if you have bus-width property set ?
> bus-width = <4>;
>
>
Yes I do.
as well as the settings above I have:
vmmc-supply = <&vaux4>;
bus-width = <4>;
ti,non-removable;
cap-power-off-card;
vaux4 is from a twl4030 and powers the wifi chip.
'cap-power-off-card' I added support for myself to so the card would power
off when not in use.
Thanks,
NeilBrown
signature.asc
Description: PGP signature
