Hi
On Mon, Nov 11, 2013 at 9:06 PM, Andreas Fenkart <afenk...@gmail.com> wrote:
> The am335x can't detect pending cirq in PM runtime suspend.
> This patch reconfigures dat1 as a GPIO before going to suspend.
> SDIO interrupts are detected with the GPIO, the GPIO will only wake
> the module from suspend, SDIO irq detection will still happen through the
> IP block.
>
> Idea of remuxing the pins by Tony Lindgren as well as the implementation
> of omap_hsmmc_pin_init.
>
> Signed-off-by: Andreas Fenkart <afenk...@gmail.com>
> ---
> .../devicetree/bindings/mmc/ti-omap-hsmmc.txt | 28 ++-
> drivers/mmc/host/omap_hsmmc.c | 189
> ++++++++++++++++++--
> include/linux/platform_data/mmc-omap.h | 4 +
> 3 files changed, 207 insertions(+), 14 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> index 1136e6b..146f3ad 100644
> --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
> @@ -21,8 +21,11 @@ ti,non-removable: non-removable slot (like eMMC)
> ti,needs-special-reset: Requires a special softreset sequence
> ti,needs-special-hs-handling: HSMMC IP needs special setting for handling
> High Speed
> ti,quirk-swakup-missing: SOC missing the swakeup line, will not detect
> -SDIO irq while in suspend. Fallback to polling. Affected chips are
> -am335x,
> +SDIO irq while in suspend. The workaround is to reconfigure the dat1 line as
> a
> +GPIO upon suspend. Beyond this option and the GPIO config, you also need to
> set
> +named pinctrl states "default", "active" and "idle ", see example below. The
> +MMC driver will then then toggle between default and idle during the runtime
> +Affected chips are am335x,
>
> ------
> | PRCM |
> @@ -49,3 +52,24 @@ Example:
> vmmc-supply = <&vmmc>; /* phandle to regulator node */
> ti,non-removable;
> };
> +
> +[am335x with with gpio for sdio irq]
> +
> + mmc1_cirq_pin: pinmux_cirq_pin {
> + pinctrl-single,pins = <
> + 0x0f8 0x3f /* MMC0_DAT1 as GPIO2_28 */
> + >;
> + };
> +
> + mmc1: mmc@48060000 {
> + ti,non-removable;
> + bus-width = <4>;
> + vmmc-supply = <&ldo2_reg>;
> + vmmc_aux-supply = <&vmmc>;
> + ti,quirk-swakeup-missing;
> + pinctrl-names = "default", "active", "idle";
> + pinctrl-0 = <&mmc1_pins>;
> + pinctrl-1 = <&mmc1_pins>;
> + pinctrl-2 = <&mmc1_cirq_pin>;
> + ti,cirq-gpio = <&gpio3 28 0>;
> + };
> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 6b0ec55..5a7fb4b 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -36,6 +36,7 @@
> #include <linux/mmc/core.h>
> #include <linux/mmc/mmc.h>
> #include <linux/io.h>
> +#include <linux/irq.h>
> #include <linux/gpio.h>
> #include <linux/regulator/consumer.h>
> #include <linux/pinctrl/consumer.h>
> @@ -213,11 +214,30 @@ struct omap_hsmmc_host {
> int req_in_progress;
> int flags;
> #define HSMMC_SDIO_IRQ_ENABLED (1 << 0) /* SDIO irq enabled */
> +#define HSMMC_SWAKEUP_QUIRK (1 << 1)
> +#define HSMMC_CIRQ_GPIO_FIRED (1 << 2)
>
> struct omap_hsmmc_next next_data;
> + struct pinctrl *pinctrl;
> + struct pinctrl_state *fixed, *active, *idle;
> struct omap_mmc_platform_data *pdata;
> };
>
> +static irqreturn_t omap_hsmmc_cirq(int irq, void *dev_id)
> +{
> + struct omap_hsmmc_host *host = dev_id;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&host->irq_lock, flags);
> + host->flags |= HSMMC_CIRQ_GPIO_FIRED;
> + disable_irq_nosync(mmc_slot(host).sdio_irq);
> + spin_unlock_irqrestore(&host->irq_lock, flags);
> +
> + pm_request_resume(host->dev); /* no use counter */
> +
> + return IRQ_HANDLED;
> +}
> +
> static int omap_hsmmc_card_detect(struct device *dev, int slot)
> {
> struct omap_hsmmc_host *host = dev_get_drvdata(dev);
> @@ -452,10 +472,25 @@ static int omap_hsmmc_gpio_init(struct
> omap_mmc_platform_data *pdata)
> } else
> pdata->slots[0].gpio_wp = -EINVAL;
>
> + if (gpio_is_valid(pdata->slots[0].gpio_cirq)) {
> + pdata->slots[0].sdio_irq =
> + gpio_to_irq(pdata->slots[0].gpio_cirq);
> + ret = gpio_request_one(pdata->slots[0].gpio_cirq,
> GPIOF_DIR_IN,
> + "sdio_cirq");
> + if (ret)
> + goto err_free_ro;
> +
> + } else {
> + pdata->slots[0].gpio_cirq = -EINVAL;
> + }
> +
> +
> return 0;
>
> +err_free_ro:
> + if (gpio_is_valid(pdata->slots[0].gpio_wp))
> err_free_wp:
> - gpio_free(pdata->slots[0].gpio_wp);
> + gpio_free(pdata->slots[0].gpio_wp);
> err_free_cd:
> if (gpio_is_valid(pdata->slots[0].switch_pin))
> err_free_sp:
> @@ -469,6 +504,69 @@ static void omap_hsmmc_gpio_free(struct
> omap_mmc_platform_data *pdata)
> gpio_free(pdata->slots[0].gpio_wp);
> if (gpio_is_valid(pdata->slots[0].switch_pin))
> gpio_free(pdata->slots[0].switch_pin);
> + if (gpio_is_valid(pdata->slots[0].gpio_cirq))
> + gpio_free(pdata->slots[0].gpio_cirq);
> +}
> +
> +static int omap_hsmmc_pin_init(struct omap_hsmmc_host *host)
> +{
> + int ret;
> +
> + host->pinctrl = devm_pinctrl_get(host->dev);
> + if (IS_ERR(host->pinctrl)) {
> + dev_dbg(host->dev, "no pinctrl handle\n");
> + ret = 0;
> + goto out;
> + }
> +
> + host->fixed = pinctrl_lookup_state(host->pinctrl,
> + PINCTRL_STATE_DEFAULT);
> + if (IS_ERR(host->fixed)) {
> + dev_dbg(host->dev,
> + "pins are not configured from the driver\n");
> + host->fixed = NULL;
> + ret = 0;
> + goto out;
> + }
> +
> + ret = pinctrl_select_state(host->pinctrl, host->fixed);
> + if (ret < 0)
> + goto err;
> +
> + /* For most cases we don't have wake-ups, and exit after this */
> + host->active = pinctrl_lookup_state(host->pinctrl, "active");
> + if (IS_ERR(host->active)) {
> + ret = PTR_ERR(host->active);
> + host->active = NULL;
> + return 0;
> + }
> +
> + host->idle = pinctrl_lookup_state(host->pinctrl,
> + PINCTRL_STATE_IDLE);
> + if (IS_ERR(host->idle)) {
> + ret = PTR_ERR(host->idle);
> + host->idle = NULL;
> + goto err;
> + }
> +
> + /* Let's make sure the active and idle states work */
> + ret = pinctrl_select_state(host->pinctrl, host->idle);
> + if (ret < 0)
> + goto err;
> +
> + ret = pinctrl_select_state(host->pinctrl, host->active);
> + if (ret < 0)
> + goto err;
> +
> + dev_info(mmc_dev(host->mmc), "pins configured for wake-up events\n");
> +
> + return 0;
> +
> +err:
> + dev_err(mmc_dev(host->mmc), "pins configuration error: %i\n", ret);
> +
> +out:
> + return ret;
> }
>
> /*
> @@ -1791,6 +1889,7 @@ static struct omap_mmc_platform_data
> *of_get_hsmmc_pdata(struct device *dev)
> pdata->nr_slots = 1;
> pdata->slots[0].switch_pin = cd_gpio;
> pdata->slots[0].gpio_wp = wp_gpio;
> + pdata->slots[0].gpio_cirq = of_get_named_gpio(np, "ti,cirq-gpio", 0);
>
> if (of_find_property(np, "ti,non-removable", NULL)) {
> pdata->slots[0].nonremovable = true;
> @@ -1837,7 +1936,6 @@ static int omap_hsmmc_probe(struct platform_device
> *pdev)
> const struct of_device_id *match;
> dma_cap_mask_t mask;
> unsigned tx_req, rx_req;
> - struct pinctrl *pinctrl;
>
> match = of_match_device(of_match_ptr(omap_mmc_of_match), &pdev->dev);
> if (match) {
> @@ -2068,10 +2166,22 @@ static int omap_hsmmc_probe(struct platform_device
> *pdev)
>
> omap_hsmmc_disable_irq(host);
>
> - pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
> - if (IS_ERR(pinctrl))
> - dev_warn(&pdev->dev,
> - "pins are not configured from the driver\n");
> + ret = omap_hsmmc_pin_init(host);
> + if (ret)
> + goto err_pinctrl_state;
> +
> + if ((mmc_slot(host).sdio_irq)) {
> + /* prevent auto-enabling of IRQ */
> + irq_set_status_flags(mmc_slot(host).sdio_irq, IRQ_NOAUTOEN);
> + ret = request_irq(mmc_slot(host).sdio_irq, omap_hsmmc_cirq,
> + IRQF_TRIGGER_LOW | IRQF_ONESHOT,
> + mmc_hostname(mmc), host);
> + if (ret) {
> + dev_dbg(mmc_dev(host->mmc),
> + "Unable to grab MMC SDIO IRQ\n");
> + goto err_irq_sdio;
> + }
> + }
>
> /*
> * For now, only support SDIO interrupt if we are booted with
> @@ -2084,8 +2194,14 @@ static int omap_hsmmc_probe(struct platform_device
> *pdev)
> mmc->caps |= MMC_CAP_SDIO_IRQ;
> if (of_find_property(host->dev->of_node,
> "ti,quirk-swakeup-missing", NULL)) {
> - /* no wakeup from deeper power states, use polling */
> - mmc->caps &= ~MMC_CAP_SDIO_IRQ;
> + /* use GPIO to wakeup from deeper power states */
> + if (!host->idle || !mmc_slot(host).sdio_irq) {
> + dev_err(mmc_dev(host->mmc),
> + "Missing GPIO config or pinctrl idle
> state\n");
> + goto err_irq_sdio;
> + }
> +
> + host->flags |= HSMMC_SWAKEUP_QUIRK;
> }
> }
>
> @@ -2113,7 +2229,13 @@ static int omap_hsmmc_probe(struct platform_device
> *pdev)
>
> err_slot_name:
> mmc_remove_host(mmc);
> - free_irq(mmc_slot(host).card_detect_irq, host);
> +err_irq_sdio:
> + if ((mmc_slot(host).sdio_irq))
> + free_irq(mmc_slot(host).sdio_irq, host);
> +err_pinctrl_state:
> + devm_pinctrl_put(host->pinctrl);
> + if ((mmc_slot(host).card_detect_irq))
> + free_irq(mmc_slot(host).card_detect_irq, host);
> err_irq_cd:
> if (host->use_reg)
> omap_hsmmc_reg_put(host);
> @@ -2158,13 +2280,15 @@ static int omap_hsmmc_remove(struct platform_device
> *pdev)
> if (host->pdata->cleanup)
> host->pdata->cleanup(&pdev->dev);
> free_irq(host->irq, host);
> + if ((mmc_slot(host).sdio_irq))
> + free_irq(mmc_slot(host).sdio_irq, host);
> if (mmc_slot(host).card_detect_irq)
> free_irq(mmc_slot(host).card_detect_irq, host);
> -
> if (host->tx_chan)
> dma_release_channel(host->tx_chan);
> if (host->rx_chan)
> dma_release_channel(host->rx_chan);
> + devm_pinctrl_put(host->pinctrl);
>
> pm_runtime_put_sync(host->dev);
> pm_runtime_disable(host->dev);
> @@ -2231,6 +2355,9 @@ static int omap_hsmmc_suspend(struct device *dev)
> OMAP_HSMMC_READ(host->base, HCTL) & ~SDBP);
> }
>
> + if (host->flags & HSMMC_SWAKEUP_QUIRK)
> + disable_irq(mmc_slot(host).sdio_irq);
> +
> if (host->dbclk)
> clk_disable_unprepare(host->dbclk);
>
> @@ -2268,6 +2395,9 @@ static int omap_hsmmc_resume(struct device *dev)
> if (ret == 0)
> host->suspended = 0;
>
> + if (host->flags & HSMMC_SWAKEUP_QUIRK)
> + enable_irq(mmc_slot(host).sdio_irq);
> +
> pm_runtime_mark_last_busy(host->dev);
> pm_runtime_put_autosuspend(host->dev);
>
> @@ -2285,23 +2415,58 @@ static int omap_hsmmc_resume(struct device *dev)
> static int omap_hsmmc_runtime_suspend(struct device *dev)
> {
> struct omap_hsmmc_host *host;
> + unsigned long flags;
> + int ret = 0;
>
> host = platform_get_drvdata(to_platform_device(dev));
> omap_hsmmc_context_save(host);
> dev_dbg(dev, "disabled\n");
>
> - return 0;
> + if (host->flags & HSMMC_SWAKEUP_QUIRK) {
> + OMAP_HSMMC_WRITE(host->base, ISE, 0);
> + OMAP_HSMMC_WRITE(host->base, IE, 0);
> + OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
> +
> + ret = pinctrl_select_state(host->pinctrl, host->idle);
> + if (ret < 0)
> + dev_warn(mmc_dev(host->mmc), "Unable to select idle
> pinmux\n");
> +
> + spin_lock_irqsave(&host->irq_lock, flags);
> + if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
> + enable_irq(mmc_slot(host).sdio_irq);
> + spin_unlock_irqrestore(&host->irq_lock, flags);
> + }
> +
> + return ret;
> }
>
> static int omap_hsmmc_runtime_resume(struct device *dev)
> {
> struct omap_hsmmc_host *host;
> + unsigned long flags;
> + int ret = 0;
>
> host = platform_get_drvdata(to_platform_device(dev));
> omap_hsmmc_context_restore(host);
> dev_dbg(dev, "enabled\n");
>
> - return 0;
> + if (host->flags & HSMMC_SWAKEUP_QUIRK) {
> + ret = pinctrl_select_state(host->pinctrl, host->active);
> + if (ret < 0)
> + dev_warn(mmc_dev(host->mmc), "Unable to select active
> pinmux\n");
> +
> + spin_lock_irqsave(&host->irq_lock, flags);
> + if (host->flags & HSMMC_SDIO_IRQ_ENABLED) {
> + if (!(host->flags & HSMMC_CIRQ_GPIO_FIRED))
> + disable_irq(mmc_slot(host).sdio_irq);
> + host->flags &= ~HSMMC_CIRQ_GPIO_FIRED;
> + OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
> + OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
> + OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
Can you move this out from the spinlock?
Michael
> + }
> + spin_unlock_irqrestore(&host->irq_lock, flags);
> + }
> + return ret;
> }
>
> static struct dev_pm_ops omap_hsmmc_dev_pm_ops = {
> diff --git a/include/linux/platform_data/mmc-omap.h
> b/include/linux/platform_data/mmc-omap.h
> index 2bf1b30..fd5fff5 100644
> --- a/include/linux/platform_data/mmc-omap.h
> +++ b/include/linux/platform_data/mmc-omap.h
> @@ -115,6 +115,7 @@ struct omap_mmc_platform_data {
>
> int switch_pin; /* gpio (card detect) */
> int gpio_wp; /* gpio (write protect) */
> + int gpio_cirq; /* gpio (card irq) */
>
> int (*set_bus_mode)(struct device *dev, int slot, int
> bus_mode);
> int (*set_power)(struct device *dev, int slot,
> @@ -145,6 +146,9 @@ struct omap_mmc_platform_data {
> int card_detect_irq;
> int (*card_detect)(struct device *dev, int slot);
>
> + /* SDIO IRQs */
> + int sdio_irq;
> +
> unsigned int ban_openended:1;
>
> } slots[OMAP_MMC_MAX_SLOTS];
> --
> 1.7.10.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
