Hi, Heiko.
Acked-by: Jaehoon Chung <jh80.ch...@samsung.com>
Best Regards,
Jaehoon Chung
On 09/30/2015 11:07 PM, Heiko Stuebner wrote:
> From: Alexandru M Stan <ams...@chromium.org>
>
> This algorithm will try 1 degree increments, since there's no way to tell
> what resolution the underlying phase code uses. As an added bonus, doing
> many tunings yields better results since some tests are run more than once
> (ex: if the underlying driver uses 45 degree increments, the tuning code
> will try the same angle more than once).
>
> It will then construct a list of good phase ranges (even ranges that cross
> 360/0), will pick the biggest range then it will set the sample_clk to the
> middle of that range.
>
> We do not touch ciu_drive (and by extension define default-drive-phase).
> Drive phase is mostly used to define minimum hold times, while one could
> write some code to determine what phase meets the minimum hold time (ex 10
> degrees) this will not work with the current clock phase framework (which
> floors angles, so we'll get 0 deg, and there's no way to know what
> resolution the floors happen at). We assume that the default drive angles
> set by the hardware are good enough.
>
> If a device has device specific code (like exynos) then that will still
> take precedence, otherwise this new code will execute. If the device wants
> to tune, but has no sample_clk defined we'll return EIO with an error
> message.
>
> Signed-off-by: Alexandru M Stan <ams...@chromium.org>
> Signed-off-by: Heiko Stuebner <he...@sntech.de>
> ---
> drivers/mmc/host/dw_mmc-rockchip.c | 162
> +++++++++++++++++++++++++++++++++++++
> 1 file changed, 162 insertions(+)
>
> diff --git a/drivers/mmc/host/dw_mmc-rockchip.c
> b/drivers/mmc/host/dw_mmc-rockchip.c
> index bc76aa2..4b3650f 100644
> --- a/drivers/mmc/host/dw_mmc-rockchip.c
> +++ b/drivers/mmc/host/dw_mmc-rockchip.c
> @@ -13,12 +13,19 @@
> #include <linux/mmc/host.h>
> #include <linux/mmc/dw_mmc.h>
> #include <linux/of_address.h>
> +#include <linux/slab.h>
>
> #include "dw_mmc.h"
> #include "dw_mmc-pltfm.h"
>
> #define RK3288_CLKGEN_DIV 2
>
> +struct dw_mci_rockchip_priv_data {
> + struct clk *drv_clk;
> + struct clk *sample_clk;
> + int default_sample_phase;
> +};
> +
> static void dw_mci_rockchip_prepare_command(struct dw_mci *host, u32 *cmdr)
> {
> *cmdr |= SDMMC_CMD_USE_HOLD_REG;
> @@ -33,6 +40,7 @@ static int dw_mci_rk3288_setup_clock(struct dw_mci *host)
>
> static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios)
> {
> + struct dw_mci_rockchip_priv_data *priv = host->priv;
> int ret;
> unsigned int cclkin;
> u32 bus_hz;
> @@ -66,6 +74,158 @@ static void dw_mci_rk3288_set_ios(struct dw_mci *host,
> struct mmc_ios *ios)
> /* force dw_mci_setup_bus() */
> host->current_speed = 0;
> }
> +
> + /* Make sure we use phases which we can enumerate with */
> + if (!IS_ERR(priv->sample_clk))
> + clk_set_phase(priv->sample_clk, priv->default_sample_phase);
> +}
> +
> +#define NUM_PHASES 360
> +#define TUNING_ITERATION_TO_PHASE(i) (DIV_ROUND_UP((i) * 360, NUM_PHASES))
> +
> +static int dw_mci_rk3288_execute_tuning(struct dw_mci_slot *slot)
> +{
> + struct dw_mci *host = slot->host;
> + struct dw_mci_rockchip_priv_data *priv = host->priv;
> + struct mmc_host *mmc = slot->mmc;
> + int ret = 0;
> + int i;
> + bool v, prev_v = 0, first_v;
> + struct range_t {
> + int start;
> + int end; /* inclusive */
> + };
> + struct range_t *ranges;
> + unsigned int range_count = 0;
> + int longest_range_len = -1;
> + int longest_range = -1;
> + int middle_phase;
> +
> + if (IS_ERR(priv->sample_clk)) {
> + dev_err(host->dev, "Tuning clock (sample_clk) not defined.\n");
> + return -EIO;
> + }
> +
> + ranges = kmalloc_array(NUM_PHASES / 2 + 1, sizeof(*ranges), GFP_KERNEL);
> + if (!ranges)
> + return -ENOMEM;
> +
> + /* Try each phase and extract good ranges */
> + for (i = 0; i < NUM_PHASES; ) {
> + clk_set_phase(priv->sample_clk, TUNING_ITERATION_TO_PHASE(i));
> +
> + v = !mmc_send_tuning(mmc);
> +
> + if (i == 0)
> + first_v = v;
> +
> + if ((!prev_v) && v) {
> + range_count++;
> + ranges[range_count-1].start = i;
> + }
> + if (v) {
> + ranges[range_count-1].end = i;
> + i++;
> + } else if (i == NUM_PHASES - 1) {
> + /* No extra skipping rules if we're at the end */
> + i++;
> + } else {
> + /*
> + * No need to check too close to an invalid
> + * one since testing bad phases is slow. Skip
> + * 20 degrees.
> + */
> + i += DIV_ROUND_UP(20 * NUM_PHASES, 360);
> +
> + /* Always test the last one */
> + if (i >= NUM_PHASES)
> + i = NUM_PHASES - 1;
> + }
> +
> + prev_v = v;
> + }
> +
> + if (range_count == 0) {
> + dev_warn(host->dev, "All phases bad!");
> + ret = -EIO;
> + goto free;
> + }
> +
> + /* wrap around case, merge the end points */
> + if ((range_count > 1) && first_v && v) {
> + ranges[0].start = ranges[range_count-1].start;
> + range_count--;
> + }
> +
> + if (ranges[0].start == 0 && ranges[0].end == NUM_PHASES - 1) {
> + clk_set_phase(priv->sample_clk, priv->default_sample_phase);
> + dev_info(host->dev, "All phases work, using default phase %d.",
> + priv->default_sample_phase);
> + goto free;
> + }
> +
> + /* Find the longest range */
> + for (i = 0; i < range_count; i++) {
> + int len = (ranges[i].end - ranges[i].start + 1);
> +
> + if (len < 0)
> + len += NUM_PHASES;
> +
> + if (longest_range_len < len) {
> + longest_range_len = len;
> + longest_range = i;
> + }
> +
> + dev_dbg(host->dev, "Good phase range %d-%d (%d len)\n",
> + TUNING_ITERATION_TO_PHASE(ranges[i].start),
> + TUNING_ITERATION_TO_PHASE(ranges[i].end),
> + len
> + );
> + }
> +
> + dev_dbg(host->dev, "Best phase range %d-%d (%d len)\n",
> + TUNING_ITERATION_TO_PHASE(ranges[longest_range].start),
> + TUNING_ITERATION_TO_PHASE(ranges[longest_range].end),
> + longest_range_len
> + );
> +
> + middle_phase = ranges[longest_range].start + longest_range_len / 2;
> + middle_phase %= NUM_PHASES;
> + dev_info(host->dev, "Successfully tuned phase to %d\n",
> + TUNING_ITERATION_TO_PHASE(middle_phase));
> +
> + clk_set_phase(priv->sample_clk,
> + TUNING_ITERATION_TO_PHASE(middle_phase));
> +
> +free:
> + kfree(ranges);
> + return ret;
> +}
> +
> +static int dw_mci_rk3288_parse_dt(struct dw_mci *host)
> +{
> + struct device_node *np = host->dev->of_node;
> + struct dw_mci_rockchip_priv_data *priv;
> +
> + priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + if (of_property_read_u32(np, "rockchip,default-sample-phase",
> + &priv->default_sample_phase))
> + priv->default_sample_phase = 0;
> +
> + priv->drv_clk = devm_clk_get(host->dev, "ciu-drive");
> + if (IS_ERR(priv->drv_clk))
> + dev_dbg(host->dev, "ciu_drv not available\n");
> +
> + priv->sample_clk = devm_clk_get(host->dev, "ciu-sample");
> + if (IS_ERR(priv->sample_clk))
> + dev_dbg(host->dev, "ciu_sample not available\n");
> +
> + host->priv = priv;
> +
> + return 0;
> }
>
> static int dw_mci_rockchip_init(struct dw_mci *host)
> @@ -95,6 +255,8 @@ static const struct dw_mci_drv_data rk3288_drv_data = {
> .caps = dw_mci_rk3288_dwmmc_caps,
> .prepare_command = dw_mci_rockchip_prepare_command,
> .set_ios = dw_mci_rk3288_set_ios,
> + .execute_tuning = dw_mci_rk3288_execute_tuning,
> + .parse_dt = dw_mci_rk3288_parse_dt,
> .setup_clock = dw_mci_rk3288_setup_clock,
> .init = dw_mci_rockchip_init,
> };
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
